Sunrise Medical 93000 instruction manual Troubleshooting, Problem Correction

Page 13

 

 

 

T

r

o

u

b l

e

s

h o

o

t

i

n

g

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TROUBLESHOOTING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PROBLEM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CORRECTION

 

 

 

 

 

 

 

 

 

 

1.

Trolley moves substantially on its own when

1.

Are posts, straight? Use level (see assembly instructions step 11).

 

 

 

 

 

 

the Easytrack System is fully assembled.

2.

Are the rails secured to the posts? Press up on the rail to make sure that the rail is latched onto the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

post.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Is the ceiling level? An uneven ceiling will make the rail uneven. See "Requirements" section in

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

manual.

 

 

 

 

 

 

 

 

 

 

2.

Extended rail comes completely apart during

1.

Rail has been extended too quickly/forcefully. Rail was pulled past the locking device.

 

 

 

 

 

 

assembly.

2.

Check locking device inside rail (top of rail above the trolley) to make sure it is not damaged.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Replace trolley if damaged. See "Easytrack Kit Contents & Part Numbers" section of manual.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Put rail back together at a slight angle and slide together.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

Slowly extend rail out again to make sure locking device clicks into place.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.

Slowly compress rail again.

 

 

 

 

 

 

 

 

 

 

 

3.

Not able to push pin to assemble/disassem-

 

 

1. Is the post still tight against the ceiling? Release pressure on posts by unscrewing blue locking

 

 

 

 

 

 

ble post.

 

 

 

device. See Disassembly instructions step 11.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

Are you lifting the upper portion of the post slightly to release pressure? Raise upper portion of post

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

first and push the pin in. See Assembly instructions step 9 or Disassembly instructions step 12.

 

 

 

 

 

 

 

 

 

 

4.

Not able to tighten post enough to hide red

1.

Have you extended the post enough? Unscrew using the blue locking handle (see Disassembly

 

 

 

 

 

 

zone.

 

 

 

instruction step 10), slide post up one or more notches, then screw the upper portion of the post to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

tighten. See Assembly instructions step 10. If the post has been "unscrewed" to the maximum and

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

will not turn anymore, reverse direction to shorten the post several inches, then slide the post up

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

another notch. See Assembly instructions steps 9-10.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

Are you holding the bottom portion of the post firm while twisting the upper portion of the post

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

towards the right? See Assembly instructions step 10.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Is the blue locking handle up out of the lower portion of the post when turning the upper portion to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the right? See Assembly instructions step 10.

 

 

 

 

 

 

 

 

 

 

5.

Posts do not appear stable.

1.

Is red zone still visible? See Assembly instructions step 12 and Troubleshooting problem #4.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

Is neoprene (rubber) on either top plate or foot plate damaged or dirty? Clean both foot plate and

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ceiling plate with soap and warm water. Make sure they dry completely before reassembling post.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Replace foot plate(s) or top plate(s) if neoprene is damaged.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

Is ceiling clean? Clean ceiling and/or floor. See "Requirements" section of manual.

 

 

 

 

 

 

 

 

 

 

6.

Trolley does not roll in rail smoothly.

1.

Is rail clean? Clean rail with damp cloth.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

Is trolley centered in rail? Re-center trolley.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Is the trolley damaged? Replace trolley. See "Easytrack Kit Contents & Part Numbers".

 

 

 

 

 

 

 

 

 

 

7.

Pivoting rail does not slide all the way over

1.

Is the pivoting rail extended far enough beyond the other rail? Lengthen pivoting rail, by pulling fur-

 

 

 

 

 

 

to one or both sides.

 

 

 

ther.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

Is the pivoting post too far from the two standard post? If the pivoting rail can't reach the swivel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

trolley rail, you need to decrease this distance. Follow Disassembly instructions and reassemble the 3-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

post Easytrack. See Figure 3 for information on dimensions and layout.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Does the pivoting rail need to be more centered between the two standard posts (Figure 30)?

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pivoting post may need to be moved so it is more centered between the two standard posts. Follow

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Disassembly instructions and reassemble 3-post Easytrack.

 

 

 

 

 

 

 

 

 

 

8.

Pivoting rail seems to be at an angle and rail

1.

Is the ceiling level? See " Requirements" section of this manual for more information.

 

 

 

 

 

 

slides freely towards one direction.

2.

Is the pivoting rail properly attached to the pivoting post? See Figure 3make sure that the proper post

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

was used. The pivoting post and standard post are not the same.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Is the extendable rail with swivel trolley secured on the post? Push up on the rail to ensure it is

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

locked.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3-Post System

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Installation T r o d u c t i o n Table of ContentsP o r t a n t Important SafeguardsJoists Q u i r e m e n t sSheet rock Floor RequirementsBefore YOU Begin F o r e Y o u B e g i nS e m b l y o f 3 P o s t S y s t e m Assembly of 3-POST SystemEasytrack 3-POST System Click Bubble S e m b l y o f O s t S y s t e m Add the stopper to the top portion of the rail S a s s e m b l y o f 3 P o s t S y s t e m Disassembly of 3-POST SystemMaintenance SpecificationsI n t e n a n c e Problem Correction TroubleshootingS y t r a c k P r o d u c t s & a c c e s s o r i e s Easytrack Products & AccessoriesR a WarrantyLimitations and Exclusions Distributed by

93000 specifications

Sunrise Medical 93000 is a premier mobility solution designed to enhance the quality of life for individuals with limited mobility. This wheelchair model combines advanced engineering and user-centered design, resulting in an exceptional user experience.

One of the standout features of the Sunrise Medical 93000 is its lightweight aluminum frame. This material offers the perfect balance of durability and portability, making it easy for users to transport and maneuver. The adjustable armrests and footrests contribute to the personalized comfort of each user, allowing for optimal positioning and support.

Another significant characteristic is the wheelchair's modular design, which allows for easy customization. Users can easily modify the chair to fit their specific needs, whether that means adjusting seat height, changing wheel types, or adding accessories. This versatility makes the 93000 suitable for a broad range of users, from those requiring basic mobility aids to more demanding applications.

In terms of technology, the Sunrise Medical 93000 incorporates an innovative wheel and tire system that enhances grip and stability on various terrains. The lightweight wheels reduce overall weight without sacrificing performance, allowing users to navigate both indoor and outdoor environments with ease.

The chair also features advanced braking systems that ensure safety during use. The intuitive design allows for easy operation of the hand brakes, giving users confidence in their ability to control their mobility. Additionally, the wheelchair is equipped with puncture-resistant tires, ensuring longevity and reliability.

Comfort is a priority in the 93000 model, evident in its cushioned seat and backrest. The upholstery is designed to be breathable and easy to clean, promoting hygiene and comfort during extended use. Furthermore, the wheelchair comes with ergonomic designs that reduce pressure points and enhance user comfort.

Lastly, Sunrise Medical emphasizes user independence with the 93000 through its thoughtful design. The wheelchair is designed to be easily operated by the user themselves, fostering a sense of autonomy and confidence. This commitment to user-centric innovation truly makes the Sunrise Medical 93000 an exemplary choice for those seeking an effective and comfortable mobility solution.
Top Page Image Contents