Samsung HT-WP30R/ELS manual On the back of the unit 2 to 3 times, Turn on the main unit

Page 8

Connecting Wireless Rear Speakers

GB

Resetting Wireless Communication

1Connect your pair of wireless rear speakers, (L) and (R), to the wireless receiver module.

2Connect the power cord of the wireless receiver module to the wall outlet and turn the power "ON".

• The Power Standby indicator will light up.

Reset the system if a communication failure occurs, or if the synchronizing signal indicator does not light up and the "REAR CHK" message blinks on the main unit's display.

Reset the system while the main unit and the wireless receiver module (SWA-2000) are in Power Standby mode.

Wireless Rear Speaker (R)

Wireless Rear Speaker (L)

GrayBlue

Back of Wireless receiver module

Caution

1 With the main unit turned off, press and hold the remote control's REMAIN button for 4 seconds.

•Press the button until the volume control indicator lights up blue. (The indicator will turn off in 1 second.)

2 With the wireless receiver module turned on, use a ball point pen or a pair of tweezers to press the RESET button

RESET Button

Back of Wireless receiver module

CONNECTIONS

•Do not connect the wireless rear speakers to the speaker outputs on the back of the main unit. Malfunction may result.

•The wireless receiving antenna is built into the wireless receiver module. Keep the unit away from water and moisture.

•For optimal listening performance, make sure that the area around the wireless receiver module location is clear of any obstructions.

To hang the wireless receiver module on the wall

on the back of the unit 2 to 3 times.

•The Standby/On LED on the front panel of the wireless receiver module blinks 3 times.

3 Turn on the main unit.

• The Link LED of the wireless receiver module is lit and the setup is finished.

• If Power Standby mode continues, repeat Steps 1 to 3 above.

1Separate wireless receiver module stand.

3 Fix the wireless receiver

Fit the speaker

module on the wall.

hole onto the screw

•

Fix the wireless receiver

on the wall to hang

(mount) the speaker.

module firmly to prevent it from falling.

13

2Fasten the screws (not supplied) on the wall.

Note

•Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too close to the main unit, some sound interruption may be heard due to interference.

•If you use a device such as a microwave oven, wireless LAN Card, Bluetooth equipment, or any other device that uses the same frequency (2.4GHz) near the system, some sound interruption may be heard due to interference.

•The transmission distance of radio wave is about 33 feet, but may vary depending on your operating environment. If a steel-concrete wall or metallic wall is between the main unit and the wireless receiver module, the system may not operate at all because the radio wave cannot penetrate metal.

Caution

•Sound will be heard from the wireless rear speakers in DVD 5.1-CH or Dolby Pro Logic II mode only.

•In 2-CH mode, no sound will be heard from the wireless rear speakers.

14

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Digital Home Cinema System Safety Warnings PrecautionsGB Class 1 Laser ProductContents Playable Discs Do not use the following types of discDisc Recording Format Copy ProtectionDescription Front Panel Rear PanelInsert Remote Batteries Range of Operation of the Remote ControlTuner button Cancel button Connecting the Speakers Module on the wall On the back of the unit 2 to 3 timesTurn on the main unit What is Progressive or Non-Interlaced Scanning? Method 1 Composite Video ............... Good QualityMethod 2 Scart ............... Better Quality Press Stop buttonCooling Fan FM antenna connectionAM antenna connection Press the Mode button until the TV indicator llights Disc terminologyGroups and tracks DVD-AUDIO Titles and chapters DVD-VIDEOSelecting the Video Format Disc PlaybackMP3-CD Playback Press Slide Mode button Jpeg File Playback JpegPress To skip to the next slide To view the previous or next image with 9 windows, pressDivX Playback USB devices that support USB Mass Storage Compatible DevicesTo stop playback, press the Stop button Fast/Slow Playback Skipping Scenes/SongsDisplaying Disc Information Checking the Remaining TimeRepeat Playback Step Function DVD VCD Angle Function DVDEZ View Function DVD Zoom Screen Enlarge Function GBDisplay 1Press Info button twicePress Info button Press Cursor Button to move to 1twice Using the Title Menu DVD Moving Directly to a Scene/SongSetting the Language Stop mode Press Menu buttonSelect ‘Language’ Then press Enter button Press Return button to return to the previous levelStop mode Adjusting the TV Aspect Ratio Screen SizePress Menu ButtonSetting the Password Enter the password Then press Enter buttonPress Menu button Then pressSetting the Wallpaper Jpeg DVD VCD Setting the WallpaperTo select one of the 3 wallpaper settings youve made Power will turn off and then back onSetting the Speaker Mode DVD Audio Disc Playback ModeSpeaker Setup, press the Enter button again DivX R registrationSetting the Delay Time Setting up the Speaker Delay TimeSetting Center Speaker Setting Rear Surround SpeakersSetting the Test Tone Stop or no discMode, press Menu buttonPress Sound Setting the Audio QualityPress Sound Edit button and then press Cursor AV Sync Setup Press DSP/EQ buttonPress PL II Effect button Dolby Pro Logic II ModePress PL II Mode Presetting Stations Listening to RadioPTY Program Type indication and PTY-SEARCH function What information can RDS signals provide?About RDS broadcasting To confirm the sleep timer setting, press Sleep button Convenient FunctionsPress Sleep button Press Dimmer buttonIndicator on the remote control flash When operating a TV with the remote controlPress the Mode button to make the TV Corresponding to your brand of TVBefore Calling for Service Symptom Check/RemedyDo not keep in direct sunlight Language Code ListCode Language Specifications Memo 1ch speaker system
Top Page Image Contents