Samsung P001/XEH manual Installing the Hob, Regulations and compliance

Page 7

Installing the Hob

Important: Be sure the new appliance is installed and grounded only by qualified

EN

personnel.

 

Please observe this instruction. The warranty will not cover any damage that may

 

occur as a result of improper installation.

 

Technical data is provided at the end of this manual.

 

Regulations and compliance

This appliance meets the following standards:

EN 60 335 - 1 and EN 60 335 - 2 - 6, relating to the safety of electrical appliances for house- hold use and similar purposes;

EN 60350, or DIN 44546 / 44547 / 44548, relating to the operating features of electric cook- ers, hobs, ovens, and grills for household use;

EN 55014 - 2;

EN 55014;

EN 61000 - 3 - 2; and

EN 61000 - 3 - 3, relating to basic requirements for electromagnetic compatibility (EMC).

This appliance complies with the following EU Directives:

73 / 23 / EWG dated 19.02.1973 (Low Voltage Directive);

89 / 336 / EWG dated 03.05.1989 (EMC Directive including Amending Directive 92 / 31 / EWG); and

93 / 68 / EWG CE Labeling Directive.

Safety instructions for the installer

A device must be provided in the electrical installation that allows the appliance to be discon- nected from the mains at all poles with a contact opening width of at least 3 mm. Suitable isolation devices include line protecting cut - outs, fuses (screw type fuses are to be removed from the holder), earth leakage trips and contactors.

With respect to fire protection, this appliance corresponds to EN 60 335 - 2 - 6. This type of appliance may be installed with a high cupboard or wall on one side.

Drawers may not be fitted underneath the hob.

The installation must guarantee shock protection.

The kitchen unit in which the appliance is fitted must satisfy the stability requirements of DIN 68930.

For protection against moisture, all cut surfaces are to be sealed with a suitable sealant.

On tiled work surfaces, the joints in the area where the hob sits must be completely filled with grout.

On natural, artificial stone, or ceramic tops, the snap action springs must be bonded in place with a suitable artificial resin or mixed adhesive.

Ensure that the seal is correctly seated against the work surface without any gaps. Additional silicon sealant must not be applied; this would make removal more difficult when servicing.

The hob must be pressed out from below when removed.

5

Image 7
Contents Ceramic Glass Hob Page Contents Following symbols are used in the text Using This ManualElectrical safety SafetyChild safety Disposing of the packaging material EN Safety during useSafety when cleaning Disposal InstructionsSafety instructions for the installer Installing the HobRegulations and compliance EN Connecting to the mains power supply Installing into the countertop 100 Cooking zones and control panel Parts and FeaturesEN Components Key features of your appliance Residual heat indicator EN Safety shutoffOther reasons why a cooking zone will switch itself off Hob Use Initial cleaningUsing suitable cookware Before You BeginUsing the touch control sensors Temperature control Switching the appliance onSwitching a cooking zone off EN Switching the appliance offSwitching the child safety lock on Using the child safety lockSwitching the child safety lock off Locking and unlocking the control panel Suggested settings for cooking specific foodsLight Soiling Cleaning and CareStubborn Soiling To avoid damaging your appliance Problem DirtEN FAQs and troubleshooting Warranty and ServiceIs it a technical fault? ServiceWhen do you incur costs even during the warranty period? Cooking rings Technical DataPage Questions or Comments
Related manuals
Manual 12 pages 11.85 Kb Manual 12 pages 47.86 Kb Manual 28 pages 46.65 Kb Manual 28 pages 4.04 Kb Manual 12 pages 35.99 Kb