Input Panel Layout, Output Panel Layout

POWER AMPLIFIER OWNER’S MANUAL

Input Panel Layout

❶ ❷ ❸ ❷ ❶ ❻ ❶ ❹ ❺

1.Gain Control – These controls are used to match the input sensitivity of the amplifier position to the particular source unit that you are using. The controls are factory set to 1Vrms.

2.Crossover Control Front and Rear – This switch turns the internal electronic high pass 18dB/Octave 85Hz crossovers on and off. If the switch is selecting HP, the crossover is on. When the switch is selects FR, the crossover is bypassed for a full range output. (Subwoofer is a fixed low pass 18dB/Octave 85Hz crossover)

3.RCA Input Jacks Front and Rear – RCA or type input jacks for use with source units that have RCA or Line Level Outputs. A source unit with a minimum output level of 200mV is required for proper operation.

4.Bass EQ – This equalization circuit is used to enhance the low frequency response of the vehicle’s interior. With up to 18 dB of boost and centered at 40Hz, the Bass EQ can be adjusted to meet your own personal taste.

5.RCA Input Jacks (Sub) – L + R inputs are supplied to simplify installation. The left and right inputs sum internally to form a single monaural channel. The left and right inputs are electronically isolated and will not affect the isolation of the other four channels. A source unit with a minimum output level of 200mV is required for proper operation.

6.EBC – The EBC, or Electronic Bass Control, allows a remote bass control to be adjusted from the dri- ver’s seat. If the optional EBC is installed, the bass level will be able to be adjusted to overcome noise and other interference.

Output Panel Layout

❶ ❷ ❹ ❸	❺ ❻	❼

1.Fuses – For convenience, all amplifiers utilize ATC type fuses. For continued protection in the event that a fuse blows, replace the fuse only with the same value.

Caution: The power fuses on the amp are for protecting the amp against overdrive. To protect the vehicle’s electrical system, an additional fuse is required within 18" of the battery on the 12V+ cable.

2.Power Terminal – This is the main power input for the amplifier and must be connected directly to the positive terminal of the car battery for the amplifier to operate properly. Use caution when running this cable through the car. Try to avoid the input RCA cables, antenna cabling, or other sensitive equipment as the large amount of current flowing through this cable can induce noise into your system. It is also very important to have a tight connection to ensure maximum performance.

3.Ground Terminal – A good quality ground is required for your Thunder Amplifier to operate at peak performance. A short length of cable the same gauge as your power cable should be used to attach the ground terminal directly to the chassis of the car. Always scrape or sand any painted surfaces to expose bare metal where the ground wire will attach.

4.Remote Terminal – All Thunder Amplifiers can be turned on by applying 12 volts to this terminal. Typically this voltage is supplied by a wire from the source unit marked “remote” or “electric antenna”.

5.Term Block Right Channel – The Right Rear + and Right Rear – terminals connect the right rear speaker to the right rear channel of the amplifier. Connect the + terminal of the speaker to the Right Rear + terminal of the amplifier and the – terminal of the speaker to the Right Rear – terminal of the amplifier. 2 ohm minimum impedance is allowed. Operation the same for front channels.

6.Term Block Left Channel – The Left Rear + and Left Rear – terminals connect the left rear speaker to the left rear channel of the amplifier. Connect the + terminal of the speaker to the left Rear + terminal of the amplifier and the – terminal of the speaker to the left Rear – terminal of the amplifier. 2 ohm minimum impedance is allowed. Operation the same for front channels.

7.Term Block Sub Channel – The sub + and sub - terminals connect the subwoofer to the dedicated sub- woofer channel of the amplifier. Connect the + terminal of the speaker to the sub + terminal of the amplifier and the – terminal of the speaker to the sub – terminal of the amplifier. 2 ohm minimum impedance is allowed.

8.Power LED (top of heatsink) - A lighted LED indicates that power has been applied to the amplifier. +12V from the battery to the +BATT terminal and +12V from a switched ignition or remote lead from a head unit. An unlighted LED indicates power has been removed or the amplifier has overheated. In the case of the overheat condition, the amplifier will turn back on after it cools down.

THUNDER895 specifications

MTX Audio has long been a staple in the world of car audio, and the THUNDER895 amplifier is a testament to the brand's commitment to delivering high-quality sound and performance. This powerful amplifier is designed to enhance the audio experience in your vehicle, providing exceptional clarity, power, and control over your sound system.

One of the most prominent features of the THUNDER895 is its substantial power output. With a maximum power rating of 800 watts, this amplifier is capable of driving multiple speakers and subwoofers without breaking a sweat. It is engineered with a Class D topology, which not only ensures high efficiency but also minimizes heat generation. This means you can enjoy impressive audio performance while keeping the internal components cool, leading to longer lifespan and reliability.

The THUNDER895 is equipped with advanced technologies that set it apart from its competitors. It features an adjustable low-pass crossover, which allows users to tune the amplifier to match their specific speaker setup. This level of customization results in a more harmonious audio experience, ensuring that every note is crisp and clear. Additionally, the amplifier includes a bass boost feature, enabling users to enhance low-frequency sounds for a more impactful listening experience.

An important characteristic of the THUNDER895 is its robust build quality. Constructed with high-grade materials and rigorous engineering standards, this amplifier is designed to withstand the rigors of daily use. Its compact design allows for flexible installation options, whether you prefer to mount it under your seat or in the trunk, ensuring that it can fit seamlessly into a variety of vehicle layouts.

Moreover, the THUNDER895 also boasts a built-in protection circuit that guards against overheating, short circuits, and overloading. This added layer of security ensures that your investment is protected while delivering consistent performance over time.

In terms of connectivity, the THUNDER895 includes a variety of input options, allowing for easy integration with existing audio systems. Whether you're looking to upgrade your current setup or build a new one from scratch, this amplifier offers versatility that caters to a wide range of audio preferences.

Overall, the MTX Audio THUNDER895 is a powerful, efficient, and durable amplifier that elevates any car audio system. Its combination of advanced technologies and user-friendly features makes it a top choice for audiophiles and casual listeners alike, ensuring that your music sounds as good as it was intended to be heard.