Draper LCD Lift Video Projector dimensions Planning, Hanging Unit, As Soon as LCD Lift Arrives

Page 1

220 Volt Installation/Operating Instructions

LCD Lift Video Projector Lift

These Installation/Operating Instructions are available in the official language of the country where you purchase the product. Please contact your distributor to request a copy.

Vous pourriez demander les instructions d’installation et d’opération traduises dans la langue officielle du pays ou vous achetez le produit. Veuillez demander à votre distributeur.

Die Gebrauchsanweisung für Installation und Konstruktion sind in der offiziellen Sprache des Landes, indem Sie das Produkt gekauft haben, vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung.

Caution

➀Read instructions completely before proceeding.

➁Follow instructions carefully. Installation contrary to instructions

invalidates warranty.

➂Do not obstruct operation of doors or universal (fl at) closure with fi ngers

or any object. Serious injury or damage could result.

➃It is not uncommon to overheat the motor during initial installation when

setting limits. The motor is thermally protected and will stop working temporarily. DO NOT physically pull the unit down when this occurs. Once it has cooled to a safe temperature, it will begin operating again.

➄LCD Lift is designed to accommodate ceiling suspended equipment. Equipment should not be allowed to rest on doors during operation.

➅Unit must be installed level (use a carpenter’s level).

➆Perform Pre-Installation Testing Procedures before beginning installation.

➇ Unit operates on 220-240 V AC current.

Note: Unit has been thoroughly inspected and tested at factory and found to be operating properly prior to shipment.

Planning

➀Based on screen location and projector specifi cations, determine proper position for projector installation.

➁Confi rm that there is adequate space available above the ceiling: 49 cm for LCD Lift A; 62 cm for LCD Lift B.

NOTE: Add an additional 2 cm of ceiling space if using ceiling closure panel.

➂Arrange to provide service access to electrical control box.

➄Use the switch to move the traveling pan up and down. Removal of the access panel will allow the observation of this movement. The unit will stop automatically when it reaches the fully up or fully down position.

➅Cycle the unit in both directions until you are satisfi ed the unit is operating properly. If for any reason the unit does not seem to operate properly, call

Draper, Inc. 765/987-7999. Do not proceed with installation.

➆If the unit has been ordered with the remote control option, again verify operation of the unit by use of the hand held transmitter. If for any reason the unit does not seem to operate properly, call Draper, Inc., 765/987-7999.

Do not proceed with installation.

➇If the unit is operating satisfactorily, remove and discard the temporary plug.

➈Disconnect the switch at the terminal board (terminals #1, #3, and #7). Do not discard this switch. It is to be used as the wall switch.

➉Replace the cover on the electrical box and proceed with the installation, referring to instructions supplied.

Hanging Unit

The LCD Lift may be installed in a variety of ways. Typically, it is recessed above the ceiling and supported by four ½" (12.7 mm) threaded mounting rods. The bottom of the LCD Lift should be recessed approximately 4 cm above the fi nished ceiling. The threaded rods should pass through mounting holes supplied in each corner and be secured by nuts above and below (see Fig. 1). The unit should then be guy wired or blocked to prevent swinging. All installations should observe the following guidelines:

➀Installer must ensure that all fasteners and supports are of adequate strength to securely support LCD Lift and projector.

Caution: DO NOT hang from, "ride" or pull down on the unit. This could create a failure and cause damage and/or injury.

➁Fastening methods must be suitable for mounting surface, and anchored so vibrations or abusive pulling will not weaken installation.

➂Unit should be level, with weight shared more or less equally by all four threaded mounting rods.

➃Bottom of unit must be unobstructed after installation. 31 cm minimum clearance is required below LCD Lift A; 37 cm below LCD Lift B.

As Soon as LCD Lift Arrives:

➀Open carton and inspect for damage.

➁ Locate the following parts:

Continued on next page

A. The unit itself

 

B. Bomb bay doors or optional ceiling closure

LCD Lift Dimensions

C. Controls

 

D. Optional SMS Low Profi le Mount with Universal Bracket

 

➂Follow Pre-Installation Testing Procedure.

Pre-Installation Testing Instructions

 

A

 

 

 

 

 

A

 

 

C

 

 

 

 

C

This LCD Lift was extensively tested and in perfect condition when it left our

 

 

 

 

 

 

plant. To make sure that it arrived in the same condition, please use the following

 

 

 

 

 

 

 

 

procedure to test the unit prior to installation. Draper does not accept back charges

 

 

 

For 12.7 mm threaded rod

 

for labor. Make sure that this unit is operating satisfactorily before installation.

B

D

 

(supplied by others)

 

 

Danger! The traveling pan can exert over 30 kg of force. Do not insert any

 

 

 

 

 

 

 

 

 

 

 

 

 

 

body parts or other objects into this unit while power is connected.

 

 

 

 

 

 

 

 

➀ Remove the unit from the outer carton.

 

 

14.3 mm dia.

 

 

 

 

➁ Remove the cover of the electrical box.

 

 

mounting holes

 

 

 

 

➂ Pre-wire supplied controls and make sure the switch is in the off position

 

 

 

 

 

 

 

 

and plug the unit into a 220V AC outlet. Caution: Do not touch any

 

 

 

 

 

 

 

 

exposed wires while the unit is plugged in.

 

 

 

 

 

 

 

 

➃ Inside the electrical box you will fi nd that a temporary plug has been

 

 

 

 

 

 

 

 

connected to the terminal board. Extend this plug from the box.

 

 

 

 

 

 

 

 

Replace the electrical box cover so that the cover is held loosely (so as not

 

 

 

 

 

 

 

 

to crush the wires) in place.

 

 

 

 

 

 

 

 

 

 

 

Bomb bay door assembly standard.

 

 

 

 

 

Flat ceiling closure panel available.

 

 

 

 

 

A

B

C

D

Travel

Lift

 

 

 

(cm)

(cm) (cm)

(cm)

(cm)

Capacity

 

 

LCD Lift A

60

45

46

28

29

30 kgs

 

 

LCD Lift B

73

57

58

41

42

30 kgs

Figure 1

 

 

 

 

 

 

 

If you encounter difficulties installing or servicing your LCD Lift, call

 

 

 

 

 

 

 

 

 

 

 

 

 

 

your dealer or Draper, Inc., Spiceland, Ind., (765) 987-7999; or fax

 

 

 

 

 

 

 

Copyright © 2008 Draper Inc. Form LCDLift220V_Inst08

Printed in U.S.A.

(765) 987-7142.

Page 1 Page 2
Image 1
Page 1 Page 2
Contents Pre-Installation Testing Instructions LCD Lift DimensionsPlanning Hanging UnitInstalling Bomb Bay Door Closure Installing Optional Ceiling ClosureElectrical Connections OperationDimensions of Traveling Pan Installing Projector Wiring Diagram-Single Station ControlSMS Low Profile with Universal Bracket 220V LCD Lift by Draper IR or RF Remote Control

LCD Lift Video Projector specifications

The Draper LCD Lift Video Projector is a premium solution designed to meet the needs of various environments, including conference rooms, lecture halls, and home theaters. This advanced projector boasts innovative technology and a range of features that elevate the viewing experience to a new level.

One of the standout features of the Draper LCD Lift is its ability to effortlessly integrate into any setting. The lift system allows the projector to be concealed within a ceiling or wall when not in use, maintaining the aesthetics of the room. With just the push of a button, the projector gracefully descends, ready to deliver stunning visuals. This elegant design not only saves space but also protects the projector from potential damage when it is not in operation.

In terms of performance, the Draper LCD Lift Video Projector utilizes cutting-edge LCD technology. This allows for vivid color reproduction, sharp contrast, and precise image clarity. With a native resolution that often exceeds Full HD, viewers can enjoy detailed images, making it ideal for showcasing presentations, videos, or high-resolution graphics. This is complemented by a high lumen output, ensuring that images remain bright and visible under various lighting conditions.

The projector also features advanced connectivity options, including HDMI, VGA, and USB ports, which allow seamless integration with computers, media players, and other devices. This versatility means that users can easily connect their preferred technology without the need for complicated setups. Additionally, the projector supports wireless connectivity options, enabling users to stream content directly from their devices, enhancing convenience and accessibility.

Another remarkable characteristic is the low noise operation, which ensures that the focus remains on the presentation without disruptive background noise. This makes it particularly suitable for environments where concentration is key, such as educational institutions or corporate meetings.

Overall, the Draper LCD Lift Video Projector embodies a commitment to quality and functionality, offering unique features that cater to both aesthetic and technical needs. Its combination of operational elegance, outstanding image quality, and versatility makes it a compelling choice for anyone seeking a reliable projection solution. Whether for professional use or personal enjoyment, this projector is designed to impress and deliver a superior viewing experience.
Top Page Image Contents