Mitsubishi Electronics 838 SERIES Lamp-Cartridge Replacement, Removing the Old Lamp Cartridge

Page 89

Appendices89

Appendix D: TV Care, continued

Lamp-Cartridge Replacement

Removing the Old Lamp Cartridge

1.Turn off TV power and unplug the TV. Allow the lamp to cool for at least one hour before proceed- ing.

2.After the lamp has cooled, remove the cover of the lamp compartment, located on the back of the TV.

Refer to figures 1 and 2. Use a #2 (medium) Phillips screwdriver to loosen the screw securing the cover. Keep the screw and cover for re-installation

3.With a medium Phillips screwdriver, loosen the two screws securing the lamp cartridge until they dis- engage from the mating threads. These are captive screws and cannot be separated from the lamp cartridge.

4.Fully open the bag supplied with the replacement lamp and set the opened bag aside.

5.Gently grasp the handle of the lamp cartridge and pull the old cartridge straight out. See figure 3.

CAUTION: Do not tilt or rotate the cartridge, as small glass fragments may fall out.

6.Without tilting or putting down the lamp cartridge, insert it into the opened bag. Close the bag while being careful not to let any glass particles fall out.

Installing the New Lamp Cartridge

1.Do not touch the glass parts of the new lamp car- tridge. Insert the new cartridge into the TV in the same orientation as the old cartridge. Push on the cartridge housing until it is fully seated.

2.Gently tighten the screws with the screwdriver.

AVOID OVERTIGHTENING!

3.Replace the plastic cover and retaining screws.

4.WASH YOUR HANDS THOROUGHLY, AS THIS LAMP CONTAINS MERCURY.

Figure 1

Figure 2

Figure 3

Use only replacement lamp part number 915B441001.

Disposal of the Old Lamp Cartridge

Contact your local authorities or the Electronic Indus- tries Alliance at www.eiae.org for lamp-disposal or recycling instructions. Do not dispose of the old lamp with common trash.

For assistance call 1(800) 332-2119

Image 89
Contents Series TV Model Stand Model Stand RequirementContents Lamp Replacement Installation and Operating NotesInternal Fans Children and TV ViewingOutdoor Antenna Grounding Replacement PartsSpecial Features of Your TV Installing the Remote Control Batteries Package ContentsTV Tips First-Time Power-OnBefore You Begin TV Controls Remote ControlPicture Tools Key and MenuTools SoundSystem Reset Status IndicatorTV Control Panel Panel-Lock ReleaseUsing the ANT Antenna Input Setting Up TV InputsSetting Up Inputs with Auto Input Sensing Memorizing Channels with Channel Scan For the ANT inputAbout Auto Input Sensing When You First Connect a DeviceAuto Input Sensing for Most Devices Tips on Auto SensingBasic TV Operation CancelSelecting an Input to Watch Watching Broadcast TVBasic Audio Controls Picture SettingsTV Care AssistanceFeature More TV FeaturesFormat Key and Picture Shape Input Selection menu Inputs Name menuDVI Video Connection Connecting a Computer to the TVHdmi Connection Computer Video Adjustments Using the TV with a Personal ComputerImage Resolution Distortion in Computer ImagesAuto Input Sensing Connection Types and Audio/Video QualityConnection Types Picture QualitySide Inputs Inputs and OutputsMain Connection Panel 2a. USB limited use Hdmi Inputs High-Definition Multimedia Interface2b. USB 838 Series LANHdmi Device IR-NetCommand Output9a. Audio Output 9b. AUDIO/SURROUND OutputSatellite Pb Pr Component Video DeviceDVI Video Device VCR or DVD Recorder to an Antenna or Wall Outlet Cable Antenna or Cable TV ServiceComposite Video Device VCR or other device with composite video outputDVD player ReceiverReceiver with Hdmi Output Supplemental Audio Connections Wireless SubwooferAdding a Subwoofer Subwoofer with Audio CableGo to Sound Global and set Center Channel to On Using the TV Speakers as a Center ChannelSetting the Sleep Timer Sleep TimerViewing or Changing the Sleep Timer FAV Favorite ChannelsUsing Custom Channel Banks Using ChannelView ListingsChannelView Channel Listings About ChannelViewAbout Channel Numbers Signal DefinitionsStatus Display Redirecting Audio Output Using an External Sound SystemControlling A/V Receiver Sound Volume Format Definitions Picture Shape and Display FormatsEffect of Mitsubishi Formats on Picture Types DVD Image Definitions3D Video Initial SetupEnhanced 3D Video Options Which Software Version Is in My TV?Enter Watching 3D VideoSide by Side Top/Bottom Screen split horizontally CheckerboardWatching Regular non-3D Video Original 3D Video OptionsEpilepsy 3D Safety RequirementsUSB Media Player Menu Camera Images and Music FilesUSB Source Devices 838 Series USB Media Setup Menu Using the Photos and Audio MenusKey For Photos or Audio Tracks Slideshow + Music --Slideshow only Music onlyPhotos and Motion Video as Composite Video Using an Audio-Only DeviceOptional Audio Cable Plug in firstPairing the TV with an Audio Playback Device Wireless Audio PlaybackResetting Bluetooth Pairing or Connection Tips for Wireless PlaybackSound Projector 838 Series Basic Manual SetupSound Projector Technology Before You BeginAdjusting Levels Adjusting Beam AnglesAdjusting an External Subwoofer How to Make Adjustments in the Custom MenuMicrophone Placement Auto SetupStart Auto Setup Initial PreparationSet Sound Global Analog Audio Out to Rear External Rear SpeakersTo TV audio Outputs Audio inputsEthernet Connection Home Network SetupStreamTV Internet Media @ # $ % * + = . space ? Wireless ConnectionKey Use for Troubleshooting Using StreamTV Internet MediaUsing Vudu Apps and Vudu Movies Getting Started with Vudu MoviesIntroduction to Home-Theater Control Source device connected directly to the TVPicture Main MenuPicture Picture+ Using PerfectColor Picture ResetUsing PerfecTint Picture PerfectPicture Mode SAP SoundSound Audio Sound Auto SP Sound GlobalSound SoundPro Center ChannelCaptions Setup Language SetupSetup Clock Setup TimerAdding/Deleting Channels Using the Channel Edit Menu Setup ChannelAnt Air Ant Cable Scan EditSetup Network Setup EnergyInputs Name InputsInputs Inputs ControlInputs Demo Inputs OrderLock TV-Y Lock ParentalLock TV Rating Movie Start Time/ Stop Time Lock Channel Lock TimeLock Panel Lock OtherImportant Note on NetCommand About NetCommand IR ControlIf You are Unable to Locate a Device’s IR Sensor PlacementIR Emitters NetCommand and Device-Specific Keys NetCommand SetupInitial NetCommand Setup Special Operation Description and Setup How to Use Adding or Removing Device Keys from NetCommand ControlControlling Most Device Types Special Operation MethodsOperating NetCommand-Controlled Devices Info NetCommand Specialized Device KeysControlling A/V Receiver Power Switching Audio to and from the A/V ReceiverControlling Other A/V Receiver Functions With Any Connection TypePower and Volume Setting Up A/V Receiver ControlSetup to Control A/V Receiver Power and Volume Before You BeginMore About Using an Hdmi Connection Automatic Audio/Video Switching Over an Hdmi ConnectionBefore You Begin Open the Inputs Learn menu Appendices Page Functions Available for Other A/V Devices Appendix a Programming the Remote ControlCode Verification Programming the Remote ControlAudio Lock Universal A/V Receiver Control Audio Amplifiers Audio AccessoriesVideo Accessories VCRs Satellite ReceiversAppendices81 Blu-ray and HD-DVD TAGBypassing the Parental Lock Mitsubishi Home Theater TVThis page intentionally left blank Enabling Hdmi Control of CEC Devices Appendix C Hdmi Control of CEC DevicesHdmi cable cannot support CEC Action Device does not have CEC compatibility ActionDescribed in Enabling Hdmi Control of CEC Hdmi Control of an Hdmi A/V Receiver and Connected DevicesResolving CEC Conflicts Using Hdmi ControlAppendix D TV Care Lamp-Cartridge ReplacementLamp To Order a New LampInstalling the New Lamp Cartridge Lamp-Cartridge ReplacementRemoving the Old Lamp Cartridge Disposal of the Old Lamp CartridgeCare of the Remote Control Cleaning RecommendationsTV Reset Comparison Guide Appendix E TroubleshootingService Picture Advanced menuChannel Edit menu instruc Affected by Picture ResetIf the New Device New Device Found screenVudu General TV Operation Symptom RemarksTV Channels Symptom Remarks Change Lamp Energy from Standard to Bright TV Power On/Off Symptom RemarksPicture Symptom Remarks Check that Digital Audio Output and/or AUDIO/SURROUND Sound Symptom RemarksSymptom Remarks Home Network Symptom RemarksNetCommand IR Control NetCommand-equipped models only Trademark and License Information Trademark and License InformationMitsubishi TV Software GNU General Public License 101 Acceptance Not Required for Having Copies GNU General Public License No Warranty Mitsubishi Home-Cinema Television Limited Warranty Warranty Index Index Page System Reset MDEAservice@mdea.com
Related manuals
Manual 40 pages 35.3 Kb

838 SERIES specifications

The Mitsubishi Electronics 838 Series represents a significant advancement in the field of industrial automation and control systems. This series is specifically designed to meet the demands of modern manufacturing environments, boasting several cutting-edge features, technologies, and characteristics that enhance productivity, reliability, and ease of use.

One of the standout features of the 838 Series is its high-performance processing capabilities. Equipped with a powerful CPU, the series can execute complex control algorithms with minimal lag, making it ideal for real-time applications. The processing speed allows for quicker response times in automation tasks, which is critical in high-speed manufacturing lines.

The 838 Series integrates advanced communication technologies, supporting various industrial protocols such as EtherNet/IP, CC-Link IE Field, and MODBUS TCP. This flexibility facilitates seamless connectivity with different devices and systems, enabling streamlined communication in multi-vendor environments. The robust networking capabilities also enhance data exchange, allowing for more integrated and efficient operations across the factory floor.

Another significant aspect of the 838 Series is its user-friendly interface. The series includes an intuitive touchscreen display, which simplifies the monitoring and control of machinery and processes. Operators can easily access vital information, adjust parameters, and receive real-time feedback, significantly reducing the learning curve associated with complex systems.

In terms of durability, the Mitsubishi 838 Series is built to withstand the rigors of industrial environments. Its construction adheres to strict quality standards, ensuring high resistance to vibration, temperature fluctuations, and electrical noise. This reliability translates into reduced downtime and maintenance costs, making it a cost-effective solution for manufacturers.

Energy efficiency is another critical characteristic of the 838 Series. It incorporates advanced power management technologies that optimize energy consumption without compromising performance. This not only helps in lowering operational costs but also aligns with the growing emphasis on sustainable manufacturing practices.

Furthermore, the series includes integrated safety features that comply with international standards. These safety mechanisms prevent potential hazards, ensuring a secure working environment for operators while maintaining productivity.

In conclusion, the Mitsubishi Electronics 838 Series stands out as a versatile and powerful solution for modern industrial automation. Its combination of high performance, flexible communication, user-friendly design, durability, energy efficiency, and robust safety features make it a leading choice for industries seeking to enhance their automation processes while ensuring operational safety and efficiency.