Oreck UPRO14T warranty Installing Power Cord, Operating Instructions

2

Cord Strain Relief

Clamp

3

Cord Strain	M5 Thumbscrew
Relief

4.	Attach desired cleaning tool	7
	(dusting brush, upholstery
	brush or crevice tool).
5.	When finished cleaning,
	replace the tool and wand to
	their storage positions. Make
	sure the wand fits tightly
	into the base inlet so it will
	not leak.

Dust Bag Full Indicator

1. Your machine has a red bag

full indicator light located on

top of the unit next to the

power switch which will

Installing Power Cord

According to your preference, you can place the power cord on the machine in one of two ways:

1.Coil the cord (starting at the machine side to prevent cord from turning) and hang it on the upper cord hook.

2.Wrap cord around the upper and lower hooks.

Operating Instructions

NOTE: This machine is suitable for voltage for 120V AC / 60 Hz.

Pre Operation Checks

1.Check to ensure a dust bag is installed. Replace bag if needed.

2.Check brush area for any thread, string or debris that may be wrapped around the brush.

	come on when the airflow is
	obstructed indicating the dust bag is full.
2.	If the light comes on, switch off the machine, unplug the cord
	and check the dust bag. Replace the bag when it is full. See
	“Dust Bag Removal and Installation”.
3.	If the light comes on and the dust bag is not full there is an
	obstruction somewhere in the system.

Dust Bag Removal	8
and Installation

1. Open the bag housing by pushing on the door latch. Fold the ends of the dust bag together and carefully remove the bag. Dispose of bag (fig 8).

Vacuuming Carpet

1.Make sure the power switch is in the “OFF” position. Plug the power cord into an electrical outlet.

2.Adjust the carpet height adjustment to suit the carpet thickness you are going to clean (fig 4).

3.Turn the main power switch on. The vacuum fan motor will turn (fig 5).

4.While holding the handle, depress the yellow release pedal and lower the handle to a convenient operating position. When the handle is lowered the brush motor will start turning (fig 6).

5.Begin vacuuming.

Remote Vacuum

Wand Cleaning

1.Keep machine in a stable position, preferably an upright position.

2.Plug in the power cord and switch on the machine as described in the “Upright Carpet Vacuum Cleaning”.

3.Remove the wand by snapping it out of the retainer clip and pulling it from its inlet. The brush motor will stop automatically when the wand is removed (fig 7).

4

1

2

3

4

5

6

2.Always install a new dust bag directly after removing a full one.

3. To install the new dust bag, push the bag onto the inlet of the fan motor as far as it will go. Fold the top down

so it will not interfere with the door latch.

4.Close the door ensuring that it latches properly.

Operating Recommendations

This new ORECK XL Professional Grade Commercial Upright is one of the finest, fastest, and strongest units in its class. You’ll love the way it cleans, and it’s easy to use.

The following are a few simple suggestions regarding its operation:

1.When the disposable filter dust bag is full, REPLACE IT. When inserting a new disposable paper filter dust bag—FIRST PUFF OUT and OPEN THE BAG.

2.Inspect and clean the filter at the vacuum motor inlet weekly.

3.If at any time the vacuum cleaner does not pick up properly or makes an unusual noise, STOP OPERATION and service.

4.Although your upright will pick up pins, paper clips, and other small objects, it is recommended that these be removed from the floor before you vacuum. Failure to do so may result in permanent damage to the motor suction fan and its housing.

5.WARNING: Do not use your vacuum cleaner on damp or wet surfaces. This will cause damage to the vacuum cleaner and is dangerous to the user. Damage caused by use on wet or damp surfaces is not covered under warranty.

6.Change the disposable filter dust bag at least once a month— even if it is not full! The collected dust in the dust bag can cause odor, attract moisture, and can affect the efficiency of the cleaner.

7.Inspect brush for wear once a month. If brush strips no longer touch the carpet, replace brush.

8.DO NOT run the vacuum cleaner over the cord. The revolving brush could damage the cord.

5