Heath Zenith MSL360FWPB manual Wire the Light Control, Black to Black White to White

Page 3

Wire the Light Control

WARNING: Turn power off at circuit breaker or fuse.

❒Remove the existing light fixture.

❒Install mounting strap to junction box using screws appropriate for your junction box.

❒The plastic hanger can be used to hold the fixture while wiring. The small end of the plastic hanger can be threaded through the hole in the center of the cover plate. The small end then goes into one of the slots on the mounting strap.

❒Thread all fixture wires through the large holes in the gasket as shown.

❒Connect the junction box wires to the light fixture wires as shown. Twist together and secure with wire connectors.

Mount the Light Control

❒Align the light control cover plate and cover plate gasket. Secure with the mounting bolt.

❒Align the three slots in the decorative shell with the lamp holder pins. Push the shell in and then twist clockwise to lock. Repeat for other shell.

Shell Slot

❒Push the rubber plug firmly into place.

❒If a wet location junction box was not used, caulk the wall plate mounting surface with silicone weather sealant.

Black to Black

White to White

Gasket

Rubber Plug

Mounting

Bolt

To avoid water damage and electrical shock, keep lamp holders 30° below horizontal.

Connect any fixture ground wire(s) to the junction box ground wire.

Lock Nut Lens

Keep lamps at least 1" (2.5 cm) from both sensors.Do not allow the lamps to block either lens.

❒Adjust the lamp holders by loosening the lock nuts but do not rotate the lamp holders more than 180° from the factory setting. When screwing in the flood lamps, do not overtighten.

598-1351-01

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Features OperationRequirements Eave Mount InstallationMode Switching Summary Wall MountBlack to Black White to White Wire the Light ControlBottom of Sensor Test and AdjustmentSpecifications Turn on the circuit breaker and light switchSymptom Possible Cause Troubleshooting GuideFuncionamiento CaracterísticasRequisitos Instalacion Resumen de las modalidades del InterruptorMontaje en pared Montaje en alero Advertencia Desconecte la energía en el disyuntor Negro a negroBlanco a blanco Evite apuntar el control hacia Prueba Y AjusteParte de abajo del detector Prenda el cortacircuitos y el interruptor de luzGuia DE Investigacion DE Averias EspecificacionesGarantía Limitada a 2 Años Servicio TécnicoFonctionnement CaractéristiquesExigences Montage mural Montage sous Avant-toit Résumé du mode de commutationBlanc / blanc Noir / noir Câblage De La Commande ’ÉclairageÉviter de pointer l’appareil Essais ET RéglagesFiche Technique Bas du détecteurGuide DE Dépannage Service Technique

MSL360FWPB specifications

Heath Zenith MSL360FWPB is a versatile motion-sensor floodlight designed to provide enhanced security and illumination for residential and commercial properties. This robust lighting solution boasts a host of innovative features and technologies that set it apart in the outdoor lighting market.

One of the standout characteristics of the MSL360FWPB is its large detection zone. The floodlight is equipped with a motion sensor that detects movement up to 240 degrees, covering areas that are typically more vulnerable to intrusions. This extensive range allows homeowners to benefit from increased security, as the light activates whenever movement is sensed within the designated area.

Another significant feature is the adjustable timer and sensitivity settings. Users can customize how long the light stays on after it detects movement, with options that typically range from a few seconds to several minutes. Additionally, the sensitivity can be fine-tuned to ensure that the light activates only when desired, reducing the chance of false alarms caused by passing animals or environmental factors.

The MSL360FWPB is not just about functionality; it also includes energy-efficient technologies. Utilizing LED bulbs, this floodlight provides bright illumination while consuming significantly less power than traditional incandescent bulbs. This energy efficiency not only leads to lower utility bills but also contributes to a more sustainable living environment.

Durability is another key characteristic of this floodlight. The MSL360FWPB is constructed from high-quality materials designed to withstand various weather conditions. With a weather-resistant rating, it can endure rain, snow, and extreme temperatures, ensuring reliable performance year-round.

Installation is made easy with the MSL360FWPB, as it includes a mounting bracket and necessary hardware, allowing for quick and hassle-free setup. This user-friendly approach means that even those with limited DIY experience can enjoy the benefits of enhanced outdoor lighting.

Overall, the Heath Zenith MSL360FWPB is a feature-rich motion-sensor floodlight that combines security, energy efficiency, and durability. Its customizable settings, broad detection range, and robust construction make it a preferred choice for property owners looking to illuminate and secure their spaces effectively. Whether for enhancing safety or simply for improved visibility, this floodlight is a reliable solution for any outdoor lighting need.
Top Page Image Contents