Heath Zenith SL-5710 manual Installation, Wall Mount Eave Mount, Mount the Light Control

Page 2

INSTALLATION

For easy installation, select an existing light with a wall switch for replacement.

Route the light control’s wires through the large gasket holes.

Twist the junction box wires and fixture wires together as shown. Secure with wire connectors.

Wall Mount

Eave Mount

For under eave installation, the sensor head must be rotated as shown in the next two steps for proper operation and to avoid the risk of electrical shock.

For eave mount only:

Mounting

Strap

Black to

Black

White to

White

Rubber

Plug

Mounting

Bolt

Gasket

screw joint.

Controls

Clamp Screw

 

Then rotate the sensor head clockwise 180° so the controls face down.

Controls

Junction box ground wire to green ground screw on fixture.

Mount the Light Control

Align the light control cover plate and cover plate gasket. Secure with the mounting bolt.

Push the rubber plug firmly into place.

If a wet location junction box was not used, caulk the wall plate mounting surface with silicone weather sealant.

Controls

If the sensor pops out of the ball joint, loosen the clamp screw and push the sensor back into the ball joint. Tighten the clamp screw when done.

Wire the Light Control

WARNING: Turn power off at circuit breaker or fuse.

Remove the existing light fixture.

Install the mounting strap as shown using two screws

Push Rubber Plug Firmly into Place.

To avoid water damage and electrical shock, keep lamp holders 30° below horizontal.

Lock Nut

Holes for Lamp

Cover Tabs

Keep lamps at least 1" (2.5 cm) from the Lens sensor. Do not allow the lamps to block the

lens.

that fit your junction box.

The plastic hanger can be used to hold the fixture

while wiring. The small end of the plastic hanger

can be threaded through the hole in the center of

the cover plate. The small end then goes into one

of the slots on the mounting strap.

Adjust the lamp holders by loosening the lock nuts but do not rotate the lamp holders more than 180° from the factory setting.When screwing in the lamps, do not overtighten.

Install the lamp covers. Align the tabs on the lamp covers with the holes on the lamp holders. Gently press lamp covers until the tabs snap into the holes on the lamp holders.

598-1120-04

Image 2
Contents Operation FeaturesMode Switching Summary Model SL-5710Wall Mount Eave Mount InstallationWire the Light Control Remove the existing light fixture Mount the Light ControlBottom of Sensor Test and AdjustmentSpecifications Maximum RangeTEN Year Limited Warranty Troubleshooting GuideNo Service Parts Available for this Product Symptom Possible CauseCaracterísticas FuncionamientoModelo SL-5710 RequisitosAdvertencia Desconecte la energía en el disyuntor InstalacionMontaje en pared Montaje en alero Negro a Blanco aParte de abajo del detector Prueba Y AjusteEspecificaciones Alcance Máximo Angulo de Cobertura MáximaNo hay piezas de servicio disponibles para este producto Guia DE Investigacion DE AveriasServicio Técnico Garantía Limitada a 10 AñosModèle SL-5710 Résumé du mode de commutationFonctionnement CaractéristiquesMontage sous Montage muralAvant-toit Bride de Montage Noir / Noir Blanc /BlancPortée maximale Angle de Fiche TechniqueBas du détecteur Le moins sensibleAucune pièce de rechange n’est disponible pour ce produit Service TechniqueGuide DE Dépannage Garantie Limitée DE 10 ANS

SL-5710 specifications

The Heath Zenith SL-5710 is an innovative motion-activated outdoor security light that showcases advanced technology designed to enhance home safety. This fixture is highly regarded for its robust features, making it an ideal choice for homeowners looking to secure their property while maintaining energy efficiency.

One of the standout features of the SL-5710 is its powerful motion sensor. With a detection range of up to 70 feet, the infrared sensor is capable of picking up movement within a wide arc. This ensures that it can effectively cover driveways, yards, and other outdoor spaces, providing peace of mind to homeowners. The sensitivity of the motion detection can be adjusted, allowing users to fine-tune the light’s responsiveness to their specific surroundings.

The SL-5710 is designed with an impressive brightness level, typically producing up to 1800 lumens. This powerful illumination is provided by energy-efficient LED bulbs, which not only provide bright light but also consume less energy compared to traditional lighting options. The use of LED technology means that the SL-5710 has a longer lifespan, reducing the need for frequent bulb replacements.

In terms of durability, the SL-5710 is built to withstand various weather conditions. The fixture boasts a rugged construction with an IP65 weatherproof rating, ensuring that it remains functional even in rain, snow, and extreme temperatures. This makes it an excellent choice for outdoor installation, providing reliable lighting regardless of the season.

The Heath Zenith SL-5710 also includes several user-friendly features, such as adjustable light duration settings. Users can set how long the light remains on after motion is detected, with options typically ranging from 10 seconds to several minutes. Additionally, the light can be set to operate in different modes, including a dusk-to-dawn feature that keeps the light on continuously after dark, enhancing security when needed most.

Installation of the SL-5710 is straightforward, with a mounting bracket that simplifies the process for homeowners. It can be mounted on walls, eaves, or poles, giving flexibility in choosing the ideal location for optimal coverage.

In summary, the Heath Zenith SL-5710 is a highly efficient and feature-rich outdoor security light. Its motion detection capabilities, energy-efficient LED illumination, durable design, and easy installation make it a go-to choice for enhancing home security while minimizing electrical costs. Whether it's for lighting up driveways, pathways, or outdoor entertaining areas, the SL-5710 stands out as a reliable and effective outdoor lighting solution.