Cadet UC102, UC101, UC072 warranty Installation Instructions, Part One

Page 2

READ ALL INSTRUCTIONS AND SAFETY INFORMATION

Installation Instructions

Part One

PLACEMENT: Read IMPORTANT INSTRUCTIONS for important safety requirements. For best results, install heater beneath a cabinet in the toe kick area. Install the Perfectoe (Model UC) horizontally. Do not install the UC heater in the floor. Headers and bracing are not necessary. Heater must be installed per the directions indicated on the lid. See clearance requirements for additional placement instructions. Install at least 6” from the inside corner and/or vertical adjacent surfaces.

CONTROLS: A thermostat is required. A Cadet electronic thermostat is recommended for ultimate control and comfort. Optional single or double pole field mount thermostat kits are also available.

IMPORTANT!

It is extremely important that you verify the electrical supply

wires are the same voltage as the heater (i.e. 120 volt heater to 120 volt power supply and 240 volt heater to 240 volt power supply). If replacing an existing heater, check the labels of the old heater and replace using the same voltage. Hooking a 240 volt heater to a 120 volt power supply will drastically reduce the heater’s output. Hooking a 120 volt heater to a 240 volt power supply will destroy the heater.

STEP 1 Turn the Electrical Power OFF

Turn the electrical power off at the electrical panel board (circuit breaker or fuse box) and lock or tag the panel board door to prevent someone from turning on power while you are working

on the heater.

STEP 2 Determine Area of Installation

The UC Series heater REQUIRES A MINIMUM distance of 6 inches from adjacent surfaces (See Figure 1). However, Cadet RECOMMENDS 12 inches from all adjacent surfaces for longer and cleaner performance. Heaters must be spaced at least 3 feet apart.

For installation in an existing wall/cabinet, cut a rough opening 14½ inches wide by 3½ inches high. Opening must be 8½ inches deep and

6 inches from adjacent wall.

Figure 1

WARNING! Vinyl floor manufacturers warn that some vinyl may discolor from temperatures in excess of 110° F. See your vinyl floor manufacturer for temperature specifications for your vinyl floor covering.

STEP 3 Route Supply Wires

For wall thermostat applications, route supply wire from circuit breaker to thermostat to rough opening. For models with an optional field mount thermostat kit, route supply wire from circuit breaker to rough opening. Allow enough wire to extend 12 inches beyond the opening. Place heater lid aside. Remove the knockout and attach the supply wire with a strain relief connector, leaving 6 inches wire lead for later use (See Figure 2).

STEP 4 Connect Supply Wires

Connect the supply ground wire to the green grounding pigtail provided (See Figure 2). Connect each supply wire to one heater wire with wire connectors. Note: All wire connections must be made inside the heater.

Figure 2

STEP 5 Mount the Heater

Reinstall heater lid and attach using four screws provided. Slide heater into opening. Fasten heater to cabinet with screws (not provided) going through the lower holes located on the flanges. Fasten grill to heater with screws provided going through the upper holes located on the flanges.

Connecting your heater to an incompatible power supply will void the warranty.

2

STEP 6 Turn the Electrical Power ON

Turn the electrical power back on at the electrical panel board (circuit breaker or fuse box).

Image 2
Contents Important Instructions Features & BenefitsOWNER’S Guide PerfectoeInstallation Instructions Part OneMaintenance Operation and MaintenanceHow to operate your heater Resetting the Manual Reset Temperature Limit ControlSymptom Problem Solution Troubleshooting ChartWarranty Parts and Service Reduce-Reuse-RecycleInstrucciones Importantes Guía Para EL PropietarioCaracterísticas y Beneficios Conserve Estas InstruccionesGarantía Instrucciones para la instalaciónParte Uno Advertencia Riesgo de electrocución Funcionamiento y mantenimientoParte dos Garantía Tabla de resolución de problemasSíntoma Problema Solution Estas Garantías no SON Pertinentes Para

UC102, UC072, UC101 specifications

The Cadet UC series, which includes models UC101, UC102, and UC072, represents a cutting-edge advancement in unmanned aerial vehicles (UAVs). These compact and versatile drones are designed for a variety of applications ranging from aerial photography and surveying to industrial inspections and environmental monitoring.

The UC101 is the entry-level model in the series, featuring a lightweight frame that enhances portability and ease of use. It is equipped with a high-resolution camera and advanced stabilization techniques that allow it to capture stunning images and videos even in challenging weather conditions. The UC101's flight time extends to approximately 30 minutes, thanks to its energy-efficient battery, which makes it suitable for various short-term missions.

On the other hand, the UC102 builds upon the foundation laid by the UC101, offering enhanced capabilities and features. One of the most notable improvements is its longer range, allowing operators to cover greater distances without losing connectivity. The UC102 is also outfitted with GPS capabilities, enabling precise navigation and automated flight paths. This feature is particularly useful for surveying and mapping applications. Additionally, the UC102 boasts superior obstacle avoidance technology, which provides an extra layer of safety during flights in complex environments.

The UC072 distinguishes itself as a high-performance model with specific features tailored for professional use. It has a robust build designed to withstand rigorous conditions, making it ideal for industrial inspections and emergency response scenarios. The UC072 incorporates real-time data transmission capabilities, allowing operators to monitor live feeds and access critical data seamlessly. Its advanced sensors provide high-resolution imagery, thermal imaging options, and LiDAR capabilities for creating detailed topographical maps.

All three models in the Cadet UC series share common characteristics, such as intuitive user interfaces and customizable flight settings. They are equipped with advanced communication technologies that facilitate real-time data exchange between the drone and the operator. Moreover, they support various payloads, enabling users to adapt the UAVs for specific missions.

Overall, the Cadet UC101, UC102, and UC072 collectively address diverse needs in the UAV market, making them popular choices for both hobbyists and professionals. With their innovative features and reliable performance, these drones are paving the way for more efficient and effective aerial applications.