Desa VP2600E, VP1600E installation manual Observed Problem Possible Cause

Page 15

OWNER’S MANUAL

TROUBLESHOOTING

Continued

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

ODS/pilot lights but flame goes out when control knob is released

1.Control knob not fully pressed in

2.Control knob not pressed in long enough

3.Equipment shutoff valve not fully open

4.Thermocouple connection loose at con- trol valve

5.Pilot flame not touching thermocouple, which allows thermocouple to cool, causing pilot flame to go out. This prob- lem could be caused by one or both of the following:

A)Low gas pressure

B)Dirty or partially clogged ODS/pilot

6.Thermocouple damaged

7.Control valve damaged

8.Safety interlock system has been trig- gered (thermostat models only)

1.Press in control knob fully

2.After ODS/pilot lights, keep control knob pressed in 30 seconds

3.Fully open equipment shutoff valve

4.Hand tighten until snug, then tighten 1/4 turn more

5.A) Contact local propane/LP gas company B) Clean ODS/pilot (see Cleaning and Maintenance, page 13) or replace ODS/ pilot assembly

6.Replace thermocouple

7.Replace control valve

8.Wait one minute for safety interlock sys- tem to reset. Repeat ignition operation

Burner(s) does not light after ODS/pilot is lit

1.

Burner orifice(s) is clogged

1.

Clean burner orifice(s) (see Cleaning

 

 

 

 

and Maintenance, page 13) or replace

 

 

 

 

burner orifice(s)

 

2.

Burner orifice(s) diameter is too small

2.

Replace burner orifice(s)

 

3.

Inlet gas pressure is too low

3.

Contact local propane/LP gas company

 

 

 

 

 

Delayed ignition of burner(s)

1.

Manifold pressure is too low

1.

Contact local propane/LP gas company

 

2.

Burner orifice(s) is clogged

2.

Clean burner orifice(s) (see Cleaning

 

 

 

 

and Maintenance, page 13) or replace

 

 

 

 

burner orifice(s)

 

 

 

 

 

Burner backfiring during combustion

1.

Burner orifice(s) is clogged or damaged

1.

Clean burner orifice(s) (see Cleaning

 

 

 

 

and Maintenance, page 13) or replace

 

 

 

 

burner orifice(s)

 

2.

Burner damaged

2.

Replace burner

 

3.

Gas regulator defective

3.

Replace gas regulator

 

 

 

 

 

Burner plaque(s) does not glow

1.

Plaque damaged

1.

Replace burner

 

2.

Inlet gas pressure is too low

2.

Contact local propane/LP gas company

 

3.

Control knob set between locked posi-

3.

Turn control knob until it locks at de-

 

 

tions

 

sired setting

 

 

 

 

 

Slight smoke or odor during initial operation

1.

Residues from manufacturing processes

1.

Problem will stop after a few hours of

 

 

 

 

operation

Heater produces a clicking/ticking noise just after burner is lit or shut off

1.Metal expanding while heating or con- tracting while cooling

1.This is common with most heaters. If noise is excessive, contact qualified ser- vice person

White powder residue forming within burner box or on adjacent walls or furniture

1.When heated, vapors from furniture pol- ish, wax, carpet cleaner, etc., turn into white powder residue

www.desatech.com

1.Turn heater off when using furniture polish, wax, carpet cleaners, or simi- lar products

Continued

103351

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualInfrared PROPANE/LP GAS Heater Safety InformationUnpacking Product FeaturesProduct Identification Local CodesConfined and Unconfined Space AIR for Combustion and VentilationProviding Adequate Ventilation Unusually Tight ConstructionAIR for Combustion Ventilation Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Check GAS Type InstallationInstallation Items Locating HeaterMethods For Attaching Mounting Bracket To Wall Installing Heater to WallMounting Bracket Removing Front Panel Of HeaterInstalling Bottom Mounting Screws Attaching Mounting Bracket To WallPlacing Heater On Mounting Bracket Typical Inlet Pipe Diameters Connecting to GAS SupplyOperating Heater For Your Safety Read Before LightingPressure Testing Heater Gas Connections Pressure Testing Gas Supply Piping SystemTo Select Heating Level Lighting InstructionsInspecting Burner Cleaning and MaintenanceObserved Problem Possible Cause Remedy TroubleshootingObserved Problem Possible Cause Gas leak. See Warning statement at TopService Hints SpecificationsReplacement Parts Service Publications TechnicalVP1600E Illustrated Parts BreakdownKEY Part Number Description QTY Parts ListVP2600E Parts List Models VP1600E GA4000B Models VP2600E GA4010B AccessoriesEquipment Shutoff Valve GA5010 Floor Mounting Stand103351 Warranty Information

VP1600E, VP2600E specifications

The Desa VP2600E and VP1600E are advanced electric heaters renowned for their efficiency and technology. These models are designed to provide rapid and consistent warmth, making them ideal for both residential and commercial applications. Their sleek design and user-friendly features ensure they can fit seamlessly into any space while providing optimal comfort.

One of the standout features of the VP2600E and VP1600E is their advanced heating technology. Both heaters are equipped with high-performance heating elements that ensure quick heat-up times and even heat distribution. This means that users can benefit from immediate warmth as soon as the unit is turned on, eliminating long wait periods commonly associated with traditional heaters.

Energy efficiency is another significant characteristic of these models. The Desa VP series has been designed to operate at a high efficiency rate, which helps in reducing energy consumption and lowering utility bills. With their built-in thermostats, these heaters can automatically adjust their output based on the ambient temperature, ensuring that energy is not wasted while maintaining a consistent level of comfort.

Safety is a top priority in the design of the Desa VP2600E and VP1600E. Both models are incorporated with multiple safety features such as tip-over protection, overheat protection, and a built-in shut-off mechanism. These features enhance user confidence, making them safe for use in homes with children and pets.

In terms of versatility, both the VP2600E and VP1600E offer adjustable settings that allow users to customize their heating experience according to personal preferences. This includes various heat settings and fan speeds, making them suitable for different occasions and environmental conditions.

Portability is another critical aspect of these heaters. With their lightweight construction and built-in handles, they can be easily moved from room to room, providing warmth wherever it is needed the most. This flexibility is particularly beneficial during seasonal changes when different areas of a home or workspace require additional heating.

In summary, the Desa VP2600E and VP1600E heaters stand out for their combination of efficient heating technology, energy savings, safety features, and portability. These characteristics make them excellent choices for anyone looking to enhance their comfort while maintaining control over their energy consumption. Whether for a cozy living room or a chilly office environment, these heaters meet diverse heating needs with reliability and ease of use.
Top Page Image Contents