PEDESTAL/LEG KIT Installation

WARNING: DO NOT OPERATE YOUR QUADRA-FIRE STOVE BEFORE FULLY ASSEMBLING ALL COMPONENTS. BURNING YOUR STOVE WITHOUT A PEDESTAL OR LEG KIT ATTACHED WILL VOID YOUR WARRANTY, AND COULD PRESENT A SERIOUS SAFETY HAZARD.

PEDESTAL MODEL

1.Place protective pad or stove pallet on floor.

2.Lay body of stove on its back on protective pad or pallet.

3.Slide pedestal over adapter on bottom of stove

4.Line up holes in sides of pedestal with holes in adapter.

5.Bolt pedestal into place, and tighten securely.

6.Carefully stand stove up and place in desired location.

7.Slip wooden decorative strips onto pedestal edges.

8.Open door of stove and check to insure firebricks and ceramic blankets are in their proper locations (see page 22-23).

Pedestal

CONNECTION TO A METAL PREFABRICATED CHIMNEY

When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be followed precisely. You must also purchase (from the same manufacturer) and install the ceiling support package or wall pass-through and “T” section package, firestops (where needed), insulation shield, roof flashing, chimney cap, etc. Maintain the proper clearance to the structure as recommended by the manufacturer. This clearance is usually a minimum of 2” (50mm), although it may vary by manufacturer or for certain components.

There are basically two methods of metal chimney installation. One method is to install the chimney inside the residence through the ceiling and the roof (Figure 12). The other method is to install an exterior chimney that runs up the outside of the residence (Figure 13). The components illustrated may not look exactly like the system you purchase, but they demonstrate the basic components you will need for a proper and safe installation.

The chimney must be the required height above the roof or other obstruction for safety and proper draft operation. The chimney must be a minimum of 3’ (914mm) higher than the highest point where it passes through the roof, and at least 2’ (610mm) higher than the highest part of the roof or structure that is within 10’ (3048mm) of the chimney, measured horizontally (Figure 5).

REMEMBER: Follow the manufacturer’s installation instructions and maintain the manufacturer’s specified clearance distances.

LEG MODEL

1.Place protective pad or stove pallet on floor.

2.Lay body of stove on its back on protective pad or pallet.

3.Screw leg base to bottom of stove.

4.Slip washers onto bolts, then bolt legs onto leg base.

5.Carefully stand stove up and place in desired location.

6.Use leveling bolts on legs to stabilize and level stove.

7.Open door of stove and check to insure firebricks and ceramic blankets are in their proper locations (see page 22-23).

Leg base

Leg

FIGURE 12

INTERIOR CHIMNEY, RUNNING THROUGH CEILING AND ROOF

Page 16

Page 13

1900 specifications

The Quadra-Fire 1900 is a premier wood-burning stove that combines traditional craftsmanship with modern technology, delivering an exceptional heating experience for homes. Known for its efficiency and elegant design, the Quadra-Fire 1900 has become a popular choice among homeowners looking to enhance their living spaces with a reliable and effective heating solution.

One of the standout features of the Quadra-Fire 1900 is its remarkable efficiency. With a heating capacity of up to 2,400 square feet, it is ideal for larger spaces, ensuring that warmth is evenly distributed throughout the room. The stove utilizes advanced combustion technology to maximize heat output while minimizing emissions, meeting stringent environmental standards and ensuring a cleaner burn.

The Quadra-Fire 1900 is equipped with a unique four-point burn system that enhances combustion performance. This system works by introducing air at multiple entry points, allowing for a more thorough burn of the wood fuel. This results in higher efficiency and less creosote buildup in the chimney, which means less maintenance for homeowners. Additionally, the stove features an adjustable damper that allows users to control the airflow and temperature, tailoring the heat output to their specific needs.

Another highlight of the Quadra-Fire 1900 is its impressive build quality. Constructed from high-quality materials, the stove embodies durability and reliability. The firebox is designed to withstand high temperatures and is lined with firebrick, which aids in heat retention and contributes to the overall efficiency of the unit. The sleek, modern design of the stove makes it an attractive focal point in any room, available in a range of finishes to complement various home decors.

For ease of use, the Quadra-Fire 1900 is designed with a large, easy-to-load door that provides ample access for refueling. The large viewing window features a clean burn technology that allows users to enjoy the aesthetic appeal of the flames while ensuring optimal performance and cleanliness.

In terms of safety, the Quadra-Fire 1900 includes several features that ensure peace of mind. An integrated blower option can be added for enhanced heat circulation, ensuring that warmth reaches every corner of the room. The stove also meets all EPA guidelines, promoting not only efficiency but also safety.

Altogether, the Quadra-Fire 1900 is a powerful, efficient, and beautifully designed wood-burning stove, making it an ideal heating solution for discerning homeowners looking to combine functionality with style. With its advanced technologies and user-friendly features, it remains a top choice in the world of wood stoves.