Sierra Products B Model manual No TE W HEN Sanding the Face of the Brush do not, Assembly

Page 2
Figure 5

Removing the brush caps: Using a small flat blade screw driver rem ove one brush cap at a tim e. Care should be taken as the brush holder has a spring that forces to the brush onto the arm ature. This

spring may cause the cap to pop out unless held firm ly

(Figure 5).

Removing and dressing the brush: Rem ove the brush from the holder by lifting up

and sliding the brush and spring clear (Figure 5). Once the brush is clear hold the brush base and carefully take a couple of swipes across the brush face with fine sand paper (Figure 6).

Figure 6

NO TE: W HEN SANDING THE FACE OF THE BRUSH DO NOT

REMOVE ANY MATERIAL. W E ARE ONLY SCUFFING THE

 

 

SURFACE TO ALLOW FOR BETTER BRUSH CONTACT.

 

Reinstalling the brush: Insert the brush back into the holder. Hold the

 

term inal tab into the holder. Carefully insert the cap and turn with a

 

sm all flat bladed screw driver. Use care not to cross thread the cap.

 

Once the cap is threaded lightly tighten against term inal tab (Figure 7).

 

Repeat service on lower brush.

 

Assembly:

 

Reconnect motor

 

wires to red and

 

black term inals.

 

Check fan blade for

 

bent blades by

 

spinning by hand. If

 

blades are not

 

aligned carefully

Figure 7

bend back into

place.

Carefully reinstall upper rear panel (Figure 8).

 

 

Figure 8

After completing the installation of the rear panel and tightening all the phillips screws. Plug the heater back into AC power and test run by

running fan motor on “Fan” setting for 2 minutes and then running on “Clean” for 30 seconds. Open hopper lid and run unit through a beginning start up by pressing “Low” and allowing fan to ignitor and fan to start up. If all appears to activate reinstall unit.

Additional inform ation is available on line@ www.sierraproductsinc.net/pages/custom er_service

Technical Custom er Service - 909-399-3355x14

5061 Brooks St. Ste B Montclair, CA 91763

800-527-4790 Fax 1-909-399-3357

www.sierraproductsinc.net

P/N Fan Motor Brush Service 08 10/08

Page 1 Page 2
Image 2
Page 1 Page 2
Contents Overview Model Fan Motor Brush Service InstructionAccessing Motor for brush Blade FigureNo TE W HEN Sanding the Face of the Brush do not Repeat service on lower brushAssembly Remove ANY MATERIAL. W E are only Scuffing

B Model specifications

Sierra Products' B Model exemplifies innovation in the realm of high-performance machinery, merging advanced technologies with robust design to deliver unmatched efficiency and reliability in various industrial applications. This model is particularly renowned for its versatility, catering to a diverse array of sectors including manufacturing, construction, and agriculture.

One of the standout features of the B Model is its powerful engine, designed to provide exceptional torque and horsepower while maintaining fuel efficiency. The engine utilizes state-of-the-art fuel injection technology, ensuring optimal combustion and lower emissions, which aligns with contemporary environmental standards. This not only enhances performance but also reduces the operational costs associated with fuel consumption.

The B Model incorporates an advanced hydraulic system, offering unparalleled lifting capabilities and precision. This system allows operators to perform heavy lifting tasks with ease, making it a valuable asset in construction and heavy-duty applications. Additionally, the hydraulic components are engineered for durability, ensuring minimal maintenance downtime and extended service life.

Another significant characteristic of the B Model is its user-friendly interface. The control panel features intuitive controls and a clear display, allowing operators of all experience levels to quickly familiarize themselves with the machine’s functions. Enhanced safety features, including automatic shut-off mechanisms and emergency alarms, further position the B Model as a reliable choice for demanding environments.

The chassis of the B Model is built from high-strength materials that contribute to its ruggedness and stability. This robust construction is essential for operating in harsh conditions, making the B Model suitable for both indoor and outdoor use. Furthermore, its compact design ensures maneuverability in tight spaces, a crucial factor for many industrial and construction applications.

In terms of technology, the B Model is equipped with telematics capabilities, providing real-time monitoring of machine performance and health. This allows for proactive maintenance scheduling and minimizes unexpected breakdowns, significantly improving productivity.

In summary, Sierra Products' B Model stands out in the market due to its powerful engine, advanced hydraulic systems, user-friendly design, and robust construction. With its innovative technologies aimed at enhancing performance and efficiency, the B Model is a prime choice for industries looking to maximize productivity while ensuring safety and reliability.
Top Page Image Contents