Procom ML200HBA, ML300HBA, ML200TBA, ML300TBA Installation, Installing Thermostat Sensing Bulb

Page 7

WARNING: Maintain the minimum clearances shown i n F i g u r e 4 . I f y o u c a n , provide greater clearances from floor, ceiling, and joining wall.

Figure 4 -Mounting Clearances As View From Front Of Heater

IMPORTANT: Vent-free heaters add moisture to the air. Although this is beneficial, installing heater in rooms without enough ventilation air may cause mildew to form from too much moisture. See Fresh Air for Combustion and Ventilation, pages 4 and 5.

INSTALLING THERMOSTAT SENSING BULB

For T-Stat Models Only

1.Pull out the sensing bulb from the two clips located in the shippng position according to the direction as shown by the arrow. There is no need to take out the two bulb clips.

2.Take out the bulb clip from the hardware package and insert it into the square hole and then insert the sensing bulb into the bulb clip (see Figure 5).

Figure 5 - Moving Thermostat Sensing Bulb

INSTALLATION

FASTENING HEATER TO WALL Mounting Bracket

The mounting bracket is located on back panel of heater (see Figure 6). It has been taped there for shipping. Remove mounting bracket from back panel.

Figure 6 -Mounting Bracket Location

Removing Lower Front Panel Of Heater

1.Remove two screws near bottom corners of lower front panel.

2.Pull bottom of lower front panel forward, then down (see Figure 7).

Figure 7 - Removing Lower Front Panel Of Heater

Methods For Attaching Mounting Bracket To Wall

Only use last hole on each end of mounting bracket to attach bracket to wall. These two holes are 16 inches apart from center. Attach mounting bracket to wall only in one of two ways:

1.Attaching to wall stud

2.Attaching to wall anchor

Attaching to Wall Stud: This method provides the strongest hold. Insert mounting screws through mounting bracket and into wall studs.

Attaching to Wall Anchor: This method allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry).

Decide which method better suits your needs. Either method will provide a secure hold for the mounting bracket.

Marking Screw Locations

1.Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is level.

WARNING: Maintain minimum clearances shown in Figure 8. If you can, provide greater clearances from floor and joining wall.

2. Mark screw locations on wall. (see Figure 8)

Note: Only mark last hole on each end of mounting bracket. Insert mounting screws through these holes only.

3.Remove tape and mounting bracket from wall.

5 8

Model ML300HBA ML300TBA

Model ML200HBA ML200TBA

Figure 8 - Mounting Bracket Clearances

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents ML200HBA ML200TBA ML300HBA ML300TBA OWNER’S Operation and Installation ManualFresh Air at once! Have P O R TA N T Read thisPropane/LP Gas Propane/LP gas Product Features Determining if you have a Confined or Unconfined Space Fresh AIR for Combustion VentilationProviding Adequate Ventilation Determining FRESH-AIR Flow for Heater LocationVentilation Air from Inside Building Ventilation AIRLocating Heater InstallationInstallation Needs Ventilation AIRInstalling Thermostat Sensing Bulb InstallationPlacing Heater On Mounting Bracket Installing Bottom Mounting ScrewsAttaching to Wall Anchor Method Important Do notImportant Install Connecting to GAS SupplyChecking GAS Connections Thermostat Models For Your Safety Read Before LightingOperating Your Heater Shutting Off Burner Only pilot stays lit NON-THERMOSTAT Models For Your Safety Read Before LightingManual Lighting Procedure Operating Your HeaterBurner Flame Pattern Cleaning ODS/PILOT and BurnerCleaning Burner Pilot AIR Inlet Hole Pilot Flame PatternObserved Problem Possible Cause Remedy TroubleshootingInlet gas pressure is too low Heater produces unwanted odors Burning vapors Specifications Thermostat Models ML200TBA ML300TBA Illustrated Parts BreakdownML200TBA, ML300TBA Parts List Thermostat ModelsNON-THERMOSTAT Models ML200HBA ML300HBA ODS/Pllot AssemblyKEY ML200HBA ML300HBA Description QTY Parts List ML200HBA ML300HBA

ML200HBA, ML300TBA, ML300HBA, ML200TBA specifications

The Procom ML300HBA, ML200TBA, ML300TBA, and ML200HBA are innovative solutions designed to meet the demands of modern data management and communication environments. Each model is tailored for specific applications, ensuring versatility, performance, and reliability across various sectors.

The Procom ML300HBA is particularly highlighted for its expansive bandwidth capabilities, making it essential for high-data-rate applications. With a user-friendly interface, it supports multiple connections, enabling streamlined data flow and minimizing latency. Its built-in redundancy features ensure that data integrity is maintained, even in challenging conditions. This device is ideal for environments where continuous operation is critical, such as broadcasting and telecommunications.

In contrast, the Procom ML200TBA offers a robust solution for applications that require high-frequency signal transmission. It provides a compact design without compromising performance. The ML200TBA is engineered with advanced noise reduction technologies, allowing it to maintain signal quality even in densely populated frequency environments. This model is particularly suitable for use in urban settings or areas with high electromagnetic interference.

The Procom ML300TBA combines the best features of the aforementioned models, offering broad bandwidth alongside high-frequency capabilities. This dual functionality makes it a standout choice for users needing flexibility in their communication systems. The ML300TBA is also equipped with sophisticated thermal management systems, ensuring optimal performance under varying environmental conditions.

Finally, the Procom ML200HBA emphasizes durability and high performance in harsh environments. Its rugged design means it can withstand adverse weather conditions, making it an excellent choice for outdoor applications. The focus on reliability ensures that users can depend on the ML200HBA for critical operations without the fear of signal loss or degradation.

In summary, the Procom ML300HBA, ML200TBA, ML300TBA, and ML200HBA are distinguished by their specific features and technologies. Each model caters to unique demands, providing exceptional performance, reliability, and flexibility that make them invaluable in today's high-stakes data environments. Whether for broadcasting, telecommunications, or rugged outdoor communications, Procom’s ML series stands ready to deliver superior performance and adaptability.
Top Page Image Contents