Marley Engineered Products Operating and Maintenance Instructions, Do not, Limited Warranty

Page 4

another heater, it is easier for the power supply connections to be made prior

to the installation of the heater(s) to the wall. If this is not possible, connections may be made through the opening in the junction boxes when the front cover(s)

is removed. See Figure 8.

UNE FOIS LES CONNEXIONS

EFFECTUÉES, REPOUSSEZ LES

CÂBLES DANS LA BOÎTE DE

JONCTION.

Figure 8. Wiring Through Junction Box Opening

5.Connecting power supply cables may be routed from heater to heater by drilling

a 1/2-inch (13mm) diameter hole in the end caps for the heaters that fit togeth- er. See Figure 9. To prevent possible damage to internal heater wiring, all drilling of end caps must be done with end caps removed from heater.

FRONT OF

HEATER

1/2" DIA. (13mm)

3"

(76mm)

115/32"

(37mm)

Figure 9. End Cap Drill Pattern

6.Wire heaters as shown in Wiring Diagram, Figure 10.

7.Replace the front covers and end caps according to “Installation of Single Unit”, Steps 12 and 13.

POWER SUPPLY

  

WIRING DIAGRAM

LIMIT

LIMIT

ELEMENT

ELEMENT

TWO HEATERS ON ONE SUPPLY

Figure 10. Dual Heater Wiring Connections

OPERATING AND MAINTENANCE INSTRUCTIONS

1.An integral or remote wall thermostat is recommended for each room. In very large rooms it is recommended that a low voltage thermostat with double or multiple circuit relays be used to provide the most comfortable results.

 

 

DO LOCATE

 

DO NOT

 

 

THERMOSTAT

 

LOCATE THERMOSTAT

A minimum of two feet

• Near televisions or

 

(61cm) from any

appliances that emit heat.

 

outside wall.

• Near drafts from an

Approximately five feet

open doorway.

 

(1,5m) from the floor,

• Where it would be struck

 

preferably on an inside

by direct rays of sunlight.

 

wall location.

 

 

2.After the baseboard system has been completely installed, all thermostats should be turned to LOW or NO HEAT setting. Then turn on breakers or install fuses. Wait 3 to 5 minutes and check to see that none of the heaters are oper- ating. If operating, disconnect power and check wiring. If none are operating then turn the thermostats to highest setting and wait 3 to 5 minutes. Check to see that all heaters are operating. Should any not be operating, disconnect power and check wiring.

3.Allow entire system to operate steadily for 1/2-hour. For a period of time after the heaters are put into operation, the owner may notice a “new smell” coming from the heaters. This is expected on new installations. Bringing heaters to full operation will eliminate this condition in a short period of time.

4.Select the setting for comfort on all thermostats.

5.To clean heater: Because of the convection heating principle which depends upon circulation of air through the finned element, dust particles will periodical-

ly be deposited between the fins and should be removed occasionally for max- imum efficiency of the heater. A vacuum cleaner with proper attachments can easily be worked along the top and bottom of the finned element to clear it of dust deposits.

NOTE: The painted finish of the heater may be cleaned with a slightly damp cloth if desired. Do not use wax cleaners or polishes as these waxes may vaporize when the heater is in operation and cause discoloration.

LIMITED WARRANTY

All products manufactured by Marley Engineered Products are warranted against defects in workmanship and materials for one year from date of installation, except heating elements which are warranted against defects in workmanship and materi- als for ten years from date of installation. This warranty does not apply to damage from accident, misuse, or alteration; nor where the connected voltage is more than 5% above the nameplate voltage; nor to equipment improperly installed or wired or maintained in violation of the product’s installation instructions. All claims for war- ranty work must be accompanied by proof of the date of installation.

The customer shall be responsible for all costs incurred in the removal or reinstal- lation of products, including labor costs, and shipping costs incurred to return prod- ucts to Marley Engineered Products Service Center.Within the limitations of this warranty, inoperative units should be returned to the nearest Marley authorized ser- vice center or the Marley Engineered Products Service Center, and we will repair

or replace, at our option, at no charge to you with return freight paid by Marley. It is agreed that such repair or replacement is the exclusive remedy available from Marley Engineered Products.

THE ABOVE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES

EXPRESSED OR IMPLIED. AND ALL IMPLIED WARRANTIES OF MER-

CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH

EXCEED THE AFORESAID EXPRESSED WARRANTIES ARE HEREBY DIS-

CLAIMED AND EXCLUDED FROM THIS AGREEMENT. MARLEY ENGINEERED

PRODUCTS SHALL NOT BE LIABLE FOR CONSEQUENTIAL DAMAGES ARIS-

ING WITH RESPECT TO THE PRODUCT, WHETHER BASED UPON NEGLI-

GENCE, TORT, STRICT LIABILITY, OR CONTRACT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

For the address of your nearest authorized service center, contact Marley Engineered Products, in Bennettsville, SC, at 1-800-642-4328. Merchandise returned to the factory must be accompanied by a return authorization and service identification tag, both available from Marley Engineered Products. When request-

ing return authorization, include all catalog numbers shown on the products.

SPX Corporation

470 Beauty Spot Rd. East

Bennettsville, SC 29512 USA

HOW TO ORDER REPAIR PARTS

In order to obtain any needed repair or replacement parts, warranty service or technical information, please contact Marley Engineered Products Service Center toll- free by calling 1-800-642-HEAT.

When ordering repair parts, always give the informa- tion listed as follows:

1.The Part Number

2.The Model Number

3.The Part Description

4.Date of Manufacture

SWO 315

5200-2083-00409/97

4

Image 4
Contents Model D Installation of Single Unit ExampleExample Clearances CM3Installation of Multiple Units Minimum CircuitOperating and Maintenance Instructions Limited WarrantyDo not Thermostat Locate Thermostat

D specifications

Marley Engineered Products D is a leading provider of advanced HVAC solutions, offering a range of products designed to improve indoor air quality and enhance energy efficiency. With a focus on innovative technologies and sustainable practices, Marley has established itself as a trusted name in the heating and cooling industry.

One of the standout features of Marley Engineered Products D is its commitment to energy efficiency. The company utilizes state-of-the-art technologies to ensure that its systems operate at optimal levels while minimizing energy consumption. This includes the use of variable speed motors and smart controls that adjust system operation based on real-time conditions. By implementing these technologies, Marley systems not only reduce energy costs for users but also contribute to the overall reduction of greenhouse gas emissions.

Another key characteristic of Marley Engineered Products D is its emphasis on reliability and durability. The products are engineered to withstand the demands of various environments, making them suitable for a wide range of applications, from residential to commercial settings. High-quality materials and rigorous testing processes ensure that the systems can perform effectively under challenging conditions, providing peace of mind to end-users.

Marley also places a strong focus on user-centric design, providing intuitive interfaces that make it easy for users to operate and manage their HVAC systems. This includes smart thermostat compatibility and mobile app integration, allowing users to control their systems remotely and receive real-time alerts for maintenance needs. Such features enhance user experience and promote proactive maintenance, further extending the lifespan of the equipment.

In addition to performance and efficiency, Marley Engineered Products D prioritizes indoor air quality. The company offers advanced filtration options that effectively capture allergens, dust, and other contaminants, ensuring that the air circulated within a space is clean and healthy. This is especially vital in today's climate, where air quality has become a significant concern for homeowners and businesses alike.

Overall, Marley Engineered Products D represents a blend of innovation, efficiency, and reliability. With its commitment to sustainable practices, user-friendly designs, and superior performance, Marley continues to lead the way in the HVAC industry, making it a preferred choice for those looking to enhance their indoor climate while reducing their environmental impact. As the demand for energy-efficient and effective heating and cooling solutions grows, Marley stands ready to meet the challenge with cutting-edge products that address the needs of modern consumers.