Monessen Hearth CSDV40SLP, CSDV40NDV, CSDV40SNV Installation for Horizontal TERMI- Nation, Purpose

Page 15

Venting installation

CSDV Series Direct Vent Gas Stove

INSTALLATION FOR HORIZONTAL TERMI- NATION

1. Determine the route your horizontal venting will take.

NOTE: The location of the horizontal vent termination on the exterior wall must meet all local and national building codes.

Snorkel terminations are available for terminations requir- ing a vertical rise on the exterior of the building. Figures 14 and 15. Follow the same installation procedures used for standard horizontal terminations. If installing the snorkel termination below grade (basement applications), you must provide proper drainage to prevent water from entering the snorkel termination. Figure 13. Do not back fill around the snorkel termination.

Snorkel

Figure 14 -

Snorkel Termination

12”

(305 mm)

Minimum

ST1137

Snorkel

Figure 15 -

Snorkel Termination with Drainage Pipe

12”

(305 mm) Minimum

Adequate

Drainage

ST1138

2.Rigid vent pipes and fittings have special twist-lock connections. Assemble the desired combination of pipe and elbows to the appliance adaptor with pipe seams oriented towards the wall or floor.

Twist-lock Procedure: The female ends of the pipes and fittings have three locking lugs (indentations). These lugs will slide straight into matching slots on the male end of adjacent pipes and fittings. Push the pipe sections together and twist one section clockwise approximately one-quarter turn until the sections are fully locked. Figure 16.

 

Female Locking

 

Lugs

NOTE: Horizontal runs

 

of vent pipe must be

 

supported every three

 

(3) feet (914 mm). Use

 

wall straps for this

Male Slots

purpose.

 

FP1953

Figure 16 -

Rigid Vent Pipe Connections

3.Attach vent pipe assembly to the stove. Set stove in front of its permanent location to insure minimum clear- ances. Mark the wall for a 9Z\x" (241 mm) square hole (for noncombustible material such as masonry block or concrete, a 7Z\x" [190 mm] diameter hole is acceptable). Figure 17. The center of the hole should line up with the center line of the horizontal rigid vent pipe. Cut a 9Z\x" x 9Z\x" (241 x 241 mm) square hole through combustible exterior wall (7Z\x" [190 mm] diameter hole if noncom- bustible). Frame as necessary. Figure 17

4.Apply a bead of non-hardening mastic around the outside edge of vent cap. Position the vent cap in the center of the 7Z\x" (190 mm) or 9Z\x" (241 mm) hole on the exterior wall with the word “UP” on the vent cap facing up. Insure proper clearance of 1" to combustibles is maintained. Attach the vent cap with four wood screws supplied. Figure 18

For vinyl siding, stucco, or wood exterior use vinyl siding standoffs between vent cap and exterior wall. The vinyl siding standoff prevents excessive heat from melting the vinyl siding material. Bolt the vent cap to the standoff. Apply non-hardening mastic around outside edge of the standoff instead of the vent cap assembly. Use wood screws pro- vided to attach the standoff. Figure 19

NOTE: Replace the wood screws with appropriate fasteners for stucco, brick, concrete, or other types of siding.

58D6056

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Models Direct Vent Gas StoveCongratulations Installation for Horizontal TerminationImportant Safety Information InstallerOwner Code Approval Important Safety InformationHigh Elevations Product featuresProduct Specifications Gas Specifications & Orifice SizeCSDV20 CSDV30 CSDV40 Stove dimensionsStove Location INSTALLATION InformationClearances to combustibles ClearancesHeight from Hearth Width Depth Model Clearances / Height RequirementsRemove Unit from Crate LogsInstallation Precautions Venting InstallationFor Horizontal Termination Venting installationInstallation Planning Installing a Vent System in AN Outside ChaseGeneral Venting Information Termination Location Canadian Installations1 US Installations2Shaded areas are acceptable Purpose Installation for Horizontal TERMI- NationHorizontal termination configuration examples Venting installationHorizontal Venting with Two 2 90 Elbows Horizontal VentingHorizontal Venting with Three 3 90 Elbows Installation for Vertical TERMINA- TionCathedral Ceiling Installation Flat Ceiling InstallationVenting with Three 3 90 Elbows Vertical Termination CONFIGURA- TionsSimpson Duravent GS 4 X 6B\, Black Pipe Venting with Two 2 90 ElbowsNumber Description Stove installation Installing gas piping to fireplace locationCheck gas type Natural Gas Electrical Wiring Remote Wall Mounted Switch Electrical InstallationLOG Placement Place CSDV20 logs in fireboxPlace rock wool ember material in firebox Place logs and rock wool ember material in firebox Place CSDV30 Logs in FireboxPlace Rock Wool Ember Material in Firebox Place CSDV40 Logs in FireboxWhat to do if YOU Smell GAS Operating InstructionsInitial lighting Leak testingMain burner switch Lighting the burnerPilot position Adjusting the AIR Shutter Venting System Cleaning and MaintenanceCleaning Glass Firebox CleaningGlass Replacement Observed Problem Possible Cause Remedy TroubleshootingReplacement Parts Description Qty Replacement PartsCSDV30 Replacement Parts CSDV30NV CSDV30PV Replacement PartsCSDV40 Replacement Parts CSDV40NV CSDV40PV Carbon Monoxide Detector Requirements If Warranty Service is Needed Mhsc

CSDV20SLP, CSDV40SLP, CSDV40NDV, CSDV20DLP, CSDV20DNV specifications

Monessen Hearth has established itself as a trusted name in the fireplace and heating industry, providing innovative and stylish solutions for residential warming needs. Among its esteemed lineup, the Monessen CSDV series offers a range of direct vent gas stoves that combine functionality with aesthetic appeal. The five notable models in this series are the CSDV40NDV, CSDV40DLP, CSDV20SNV, CSDV20DLP, and CSDV20SLP, each designed to cater to different preferences and needs while delivering exceptional performance.

The CSDV40NDV and CSDV40DLP are both 40-inch models that stand out for their impressive heating capacity and larger burn area. The CSDV40NDV features a stunning, traditional style including arched glass doors that enhance its elegance. The deep ceramic glass provides an expansive view of the flickering flames, while the optional blower increases efficiency by distributing heat throughout the room. The CSDV40DLP, on the other hand, offers a more contemporary design, integrating clean lines and modern aesthetics but still providing the same impressive heating capabilities.

Shifting focus to the CSDV20 models, the CSDV20SNV and CSDV20DLP are both 20-inch units, perfect for smaller spaces or for creating a cozy ambiance without overwhelming a room. The CSDV20SNV features a stylish traditional design with a sleek black finish and decorative detailing, while the CSDV20DLP offers a more modern take, showcasing clean lines and simplicity. Both models benefit from advanced technology that allows them to maintain consistent temperatures while efficiently utilizing fuel.

All models in the CSDV series feature Monessen's patented burner technology, which produces realistic flames and ensures efficient operation. With direct vent capabilities, these stoves safely vent combustion gases outside, making them a clean and safe option for homeowners. Additionally, they boast easy-to-use thermostatic controls that empower users to maintain their desired temperature effortlessly.

Energy efficiency is another hallmark of the CSDV range, with many units qualifying for efficiency rebates depending on local utilities. Overall, the Monessen Hearth CSDV series offers a compelling combination of style, efficiency, and advanced technology, making it an excellent choice for anyone looking to enhance their indoor space with a dependable heating solution.
Top Page Image Contents