Monessen Hearth HVFL18 manual Rock Wool and LOG Placement, Back Burner, Placing Rock Wool

Page 26

ROCK WOOL AND LOG PLACEMENT

Before you begin — This unit is supplied with four or five ceramic fiber logs. Do not handle these logs with your bare hands. Always wear gloves to prevent skin irritation from ceramic fibers. After handling the logs, wash your hands gently with soap and water to remove any traces of fibers.

WARNING

The positioning of the logs are critical to the safe and clean operation of this heater. Sooting and other problems may result if the logs are not properly and firmly positioned in the appliance. Never add additional logs or embellishments such as pine cones, vermiculite or rock wool to the heater. Only use the logs and EB-RW (rock wool) supplied with the unit.

Failure to position the parts in accordance with diagrams below or to use only parts specifically approved for this heater may result in property damage or personal injury.

PLACING ROCK WOOL

Starting on the second row of burner ports, place EB-RW (Rock Wool) in dime-size pieces on the second row of ports and going toward

back of front burner.

.

NOTE: Do not put EB-RW (Rock Wool) on first row of burner ports.

Dime-Size Rock Wool

WARNING

• Use only EB-RW provided with log set.

• Do not add additional rock wool.

 

 

• Place EB-RW (rock wool) on front burner

 

ports only. DO NOT PLACE EB-RW ON

 

BACK BURNER!

 

 

INSTALLING KENTUCKY STACK LOGS ON GRATE

1.Install back log (#1) on two pins located near the back of

base. Check log position and stability. See Figure 26.

First Row of Ports (Leave Open)

Figure 25 - Placing Rock Wool

Back Log #1

Pins

Figure 26 - Installing Back Log

26

59D1015

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Read and Save These Instructions What to do if YOU Smell GASContents Owner Important Safety InformationInstaller Never connect unit to private Make Sure YOU have Received ALL Parts What YOU will Need for InstallationGetting Started PROPANE/LPG Product Features and SpecificationsNatural GAS Thermal Generator Ignition ControlsPILOT/ODS Adequate Combustion and Ventilation AIR General Installation InformationCodes BTU/Hr = 151/2 x 12 x 8 x 1000 = 29760 BTU/Hr Fireplace and Hearth Dimensions Hearth Minimum DimensionPlacement in a Fireplace with a Restrictive Barrier Height of Restriction Minimum Depth of Fireplace/FireboxClearances and Height Requirements Sidewall and Ceiling ClearancesClearances and Height Requirements Measuring Heat Resistant Material for Mantel Clearances and Height Requirments ExampleExample Floor Clearance Minimum Clearance above Combustible FlooringBefore Installing the Appliance Installing Vented ApplicationsBefore Fully Installing the Unit Damper Stop InstallationPlacing and Securing Appliance Installing Vented ApplicationsAssembly Procedure Connecting the GAS Flexible Tube Manual Shutoff Gas Supply Inlet ValveChecking GAS Pressure Manual Control FigureOperate Electrical Wiring MILLI-VOLTConnecting Optional Wall Switch or Thermostat Connecting Remote Receiver Installing T-STAT Sensor Option Sold SeparatelyInstalling T-Stat Sensor to Hvfl Base With Screw Provided Complete MILLI-VOLT System Check Operation of Thermostat SensorChecking System Operation Back Burner Rock Wool and LOG PlacementInstalling Kentucky Stack Logs on Grate Placing Rock WoolLOG Placement See FigureInstalling Split Maple Logs on Grate Installing Back Log #1Installing Top Right Log #5 Checking the Pilot Flame Flame AppearancePlacing the Decorative Rock MILLI-VOLT Control and Thermostat ControlChecking the Burner Flame Operating InstructionsOperating Instructions What to do if YOU Smell GASManual Control Lighting Instructions MILLI-VOLT Control Lighting Instructions Operating Instructions and Cleaning and Servicing Cleaning and ServicingTroubleshooting Observed Problem Possible Cause RemedyODS/pilot lights, but flame Replacement Parts Burner AssemblyReplacement Parts List HVFL18 HVFL24Kentucky Stack Logs KSCL18 KSCL24 KSCL30Split Maple Logs SMRL18 SMRL24 SMRL30Carbon Monoxide Detector Requirements Special Requirements Basic Warranty Lifetime WarrantyFive Year Warranty

HVFL18 specifications

The Monessen Hearth HVFL18 represents a notable innovation in the realm of vent-free fireplaces, designed with both aesthetics and functionality in mind. This unit is an excellent choice for homeowners looking for an efficient heating solution that combines style and convenience in one compact design.

One of the standout features of the HVFL18 is its impressive heat output. This fireplace boasts a maximum of 18,000 BTUs, making it powerful enough to warm various room sizes effectively. The vent-free design allows for maximum efficiency, ensuring that all the heat generated stays within the living space. Additionally, this model uses natural gas or propane, providing flexibility for installation based on the homeowner's preferences and existing connections.

The aesthetic appeal of the Monessen Hearth HVFL18 cannot be overlooked. It is designed with a realistic flame appearance that mimics the look of a traditional wood fire. The unit comes with a variety of decorative front options, allowing homeowners to customize the overall look to fit their interior design. Whether you're aiming for a contemporary or more classic style, the HVFL18 can complement your home beautifully.

A key technology integrated into the HVFL18 is its advanced burner system. The system is designed to produce taller, flickering flames, enhancing the ambiance of a cozy fire. Along with this, the unit incorporates a built-in oxygen depletion sensor, which automatically shuts off the fireplace if oxygen levels in the room fall below a safe threshold, ensuring peace of mind for users.

Ease of use is another significant characteristic of the HVFL18. The fireplace features an intuitive electronic ignition system, which simplifies the process of starting the unit and allows for quick adjustments to the flame height. Homeowners will appreciate how easily they can obtain instant warmth with just the press of a button.

Furthermore, the Monessen Hearth HVFL18 is designed for easy installation. With no need for venting, it can be added to a variety of spaces in homes where traditional fireplaces might be impractical. The compact size makes it suitable for smaller rooms, while still delivering robust heating performance.

In conclusion, the Monessen Hearth HVFL18 combines exceptional heating power, aesthetic versatility, and state-of-the-art technology, making it a top choice for those seeking a stylish and efficient fireplace solution. Its blend of safety features, user-friendly operation, and attractive design ensures that it will enhance any home while providing warmth and comfort during colder months.
Top Page Image Contents