Vanguard Heating VMH3000TN Inspecting Burner, Pilot Flame Pattern, Burner Flame Pattern

Page 15

OWNER’S MANUAL

OPERATING

HEATER

Continued

THERMOSTAT

CONTROL OPERATION

The thermostatic control used on this heater differs from standard thermostats. Standard thermostats simply turn on and off the burner. The thermostat used on this heater senses the room temperature. The thermostat adjusts the amount of gas flow to the burner. This increases or de- creases the burner flame height. At times the room may exceed the set temperature. If so, the burner will shut off. The burner will cycle back on when room temperature drops below the set temperature.

The control knob can be set to any heat level between HI and LO.

Note: The thermostat sensing bulb mea- sures the temperature of air near the heater cabinet. This may not always agree with room temperature (depending on housing construction, installation loca- tion, room size, open air temperatures, etc.). Frequent use of your heater will let you determine your own comfort levels.

MANUAL LIGHTING

PROCEDURE

1.Remove front panel (see Figure 2, page 3).

2.Follow steps 1 through 5 under Light- ing Instructions, page 14.

3.With control knob pressed in, strike match. Hold match to pilot until pi- lot lights.

4.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow step 8 under Lighting Instruc- tions, page 14.

5.Replace front panel.

INSPECTING

BURNER

Check pilot flame pattern and burner flame pattern often.

PILOT FLAME PATTERN

Figure 25 shows a correct pilot flame pattern. Figure 26 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touch- ing the thermocouple. This will cause the thermocouple to cool. When the thermo- couple cools, the heater will shut down.

If pilot flame pattern is incorrect, as shown in Figure 26

•turn heater off (see To Turn Off Gas to Appliance, page 14)

•seeTroubleshooting, pages 16 through 18

Pilot Burner

Thermocouple

GOOD PILOT

GRH/OV 0

Figure 25 - Correct Pilot Flame Pattern

Pilot Burner

Thermocouple

BAD PILOT/LP

GRH/OV 008

Figure 26 - Incorrect Pilot Flame Pattern

BURNER FLAME PATTERN

Figure 27 shows a correct burner flame pattern. Figure 28 shows an incorrect burner flame pattern. The incorrect burner flame pattern shows yellow tipping of the flame. It also shows the flame higher than one inch above the log.

Note: When using the heater the first time, the flame will be yellow for approximately one hour until the log cures.

WARNING: If yellow tipping occurs, your heater could pro- duce increased levels of carbon monoxide. If burner flame pat- tern shows yellow tipping, follow instructions, bottom of this page.

NOTICE: Do not mistake orange flames with yellow tipping. Dirt or other fine particles enter the heater and burn causing brief patches of orange flame.

If burner flame pattern is incorrect, as shown in Figure 28

•turn heater off (see To Turn Off Gas to Appliance, page 14)

•seeTroubleshooting, pages 16 through 18

Top of Flame About

One Inch Above Logs

Figure 27 - Correct Burner Flame Pattern

Yellow Tipping

Figure 28 - Incorrect Burner Flame Pattern

104431

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualLocal Codes Safety InformationUnpacking AssemblyProduct Features Product IdentificationAssembling and Attaching Brass Trim Attaching Brass Front Trim to Front PanelConfined and Unconfined Space AIR for Combustion and VentilationProviding Adequate Ventilation Unusually Tight ConstructionAIR for Combustion Ventilation Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Locating Heater InstallationInstallation Items Check GAS TypeInstallation Options Thermostat Sensing BulbMounting Heater to Wall Placing Heater On Mounting Bracket Installing Bottom Mounting ScrewsMounting Heater on Optional Hearth Base Mounting Heater to Optional Hearth BaseSecuring Hearth Base to Floor Connecting to GAS Supply Mounting Heater to Optional MantelAssembling Mantel Pressure Testing Gas Supply Piping System Pressure Testing Heater Gas ConnectionsChecking GAS Connections To Turn OFF GAS To Appliance For Your Safety Read Before LightingOperating Heater Lighting InstructionsInspecting Burner Pilot Flame PatternBurner Flame Pattern Observed Problem Possible Cause Remedy TroubleshootingMaintenance, Gas leak. See Warning statement at Cleaning and Maintenance Replacement PartsService Hints VMH3000TN Illustrated Parts BREAKDOWN21KEY VMH3000TN Description QTY Parts ListTechnical Service SpecificationsPremier Mantel AccessoriesEquipment Shutoff Valve GA5010 FAN KitsInternational Warranty Information

VMH3000TN specifications

The Vanguard Heating VMH3000TN is a state-of-the-art heating solution designed to deliver efficient warmth and comfort in a variety of environments. Its innovative features and advanced technologies make it an ideal choice for both residential and commercial applications.

One of the standout features of the VMH3000TN is its powerful heating capacity. With a substantial output, this unit can quickly warm large spaces, ensuring that every corner of the room reaches a comfortable temperature. This makes it perfect for homes, offices, workshops, and other facilities that require reliable heat distribution.

The VMH3000TN comes equipped with advanced energy-efficient technology. It incorporates a high-performance heat exchanger that maximizes thermal efficiency, helping to reduce energy consumption and lower heating costs. This makes it an environmentally-friendly option for consumers looking to minimize their carbon footprint while enjoying the benefits of effective heating.

Another notable characteristic of the VMH3000TN is its user-friendly interface. The product features intuitive controls that allow users to customize their heating experience easily. With programmable settings, users can set specific heating schedules according to their lifestyle, ensuring that spaces are warm when needed without excessive energy use.

Safety is also a priority in the design of the VMH3000TN. It is equipped with multiple safety features, including overheat protection and a reliable thermostat. These systems work together to prevent potential hazards, giving users peace of mind while using the heater.

Durability and reliability are additional attributes of this model. Constructed with high-quality materials, the VMH3000TN is built to withstand the rigors of daily use. Its robust design ensures longevity, making it a worthwhile investment for those seeking a long-term heating solution.

The VMH3000TN is also designed with versatility in mind. Its sleek and compact design enables it to fit seamlessly into a variety of spaces and decor styles. It can be easily installed in homes, garages, or offices without taking up excessive space.

In summary, the Vanguard Heating VMH3000TN is a powerful, efficient, and reliable heating solution that caters to diverse heating needs. Its array of features, safety mechanisms, and user-friendly operation make it a top choice for consumers seeking effective climate control. Whether for personal comfort or professional use, the VMH3000TN promises to deliver warm and inviting spaces all winter long.
Top Page Image Contents