Heat & Glo LifeStyle CFX-Grand-B, FB-Grand manual Installing the Insert, Installing the Vent System

Page 14

Installing the Insert

Step 1. Installing the Vent System

Vent System Installation Precautions

Before starting installation of vent kits, the installer should read these instructions and the Vent Kit Instructions to ensure that a proper vent installation is completed.

Consult your local building codes before beginning the installation.

WARNING: THIS GAS INSERT AND VENT AS- ! SEMBLY MUST BE VENTED DIRECTLY TO THE OUTSIDE AND MUST NEVER BE ATTACHED TO A CHIMNEY SERVING A SEPARATE SOLID FUEL BURNING APPLIANCE. EACH GAS APPLIANCE MUST USE A SEPARATE VENT SYSTEM. COMMON VENT SYSTEMS ARE PROHIBITED.

Vent System Approvals

Models CFX-Grand-B, CFX-IN-B, FB-IN and FB-GRAND is approved with vent termination kits LINK-DV-30, LINK-DV- 30B, LINK-DV4-30 and LINK-DV4-30B. Approved vent sys- tem terminations are labeled for identification. 3-inch diam- eter listed flexible aluminum and stainless steel gas vent is used for both the incoming combustion air and exhaust vent pipes. NO OTHER VENTING SYSTEMS OR COM- PONENTS MAY BE USED. Detailed installation instruc- tions are included with each vent termination kit and should be used in conjunction with this manual.

Horizontal Venting

The vent system on this model CANNOT be terminated horizontally.

Vertical Venting

The vent pipes MUST be connected to the proper collars on the unit AND the exhaust vent pipe MUST be connected to the termination cap or the unit will not operate. The com- bustion air vent pipe CAN be connected to the termination cap (LINK -DV30, LINK -DV30B) or it can terminate inside the chimney (LINK-DV4-30, LINK-DV4-30B). The bottom opening of the chimney must be sealed around the vent pipes if the combustion air vent is NOT connected to the termination cap. See Figures 3 and 4.

NOTE: The minimum vertical rise (exhaust vent) is 14 feet and the maximum vertical rise is 40 feet. These dimensions are measured from the starting collars of the unit to the end

of the last section of vent pipe. See dimension V in Figure 4.

A vertical vent termination system installed on this model will include one (1) length of 3-inch flexible vent pipe for the combustion air, one (1) length of 3-inch flexible vent pipe for the exhaust air, one (1) pipe-to-cap adaptor, and one (1) SLK-991DA or SLK-980D Vertical Termination Cap.

NOTE: The damper of the masonry chimney may need to be removed to allow installation of the flexible-vent pipe.

This fireplace has been altered to accommodate an insert and should be inspected by a qualified person prior to re-use as a conventional fireplace.

NOTE: The above label, located in the instruction package, must be affixed to the existing fireplace prior to installation.

For zero clearance factory built woodburning fireplaces, the use of kit LINK-ZC-ADP in place of the standard square flashing will allow you to mount the adaptor and cap on metal pipe. Additionally, the use of kit FLASH-DAMP will seal off the damper opening when terminating the inlet air vent pipe just above the damper. These 2 kits are recommended for zero clearance, factory built woodburning fireplaces.

Connecting the Vent Pipe

Install the 3” flexible vent pipe(s) down through the chimney. Secure the end of the flexible vent pipe for exhaust to the provided 3’ section of stainless steel flexible vent pipe. A 3” collar is factory installed on one end for mating the two ends of flexible pipe.

WARNING: THE 3’ SECTION OF STAINLESS ! STEEL FLEXIBLE PIPE MUST BE ATTACHED DI- RECTLY TO THE EXHAUST COLLAR OF THE UNIT.

Attach either 4’ or 30’ section of intake liner to the intake collar on the collar slide-plate using 3 screws. This assembly may be removed from the unit to aid installation. Slide insert into position, while pulling intake collar assembly towards the front of the unit. Slide the gas insert into place, and position any excess flexible vent pipe back up into the chimney. This assembly will be secured in place when the pull handle can be locked into position at locking brackets.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents What to do if you smell gas Models FB-GrandCFX-Grand-B Safety and Warning Information Table of Contents Service Parts Log Set AssemblyFB-GRAND GLA-FBGCFX-GRAND-B 14 4 Log Set Assembly FB-IN, CFX-IN-BFB-IN GLA-FBINCFX-IN-B U u uApprovals Codes Installation CodesHigh Altitude Installations Appliance CertificationIntroducing the Heat-N-Glo Gas Appliances Pre-install PreparationGetting Started Minimum Fireplace Size Height 25-3/4 654 22-1/2Diagram and dimension of all models Model DimensionsInstalling the Insert Installing the Vent SystemHorizontal Overhang Minimum Height from Roof to Lowest Discharge OpeningTermination Typical configuration of vent liners Gas Supply Line Positioning, Leveling, Securing the InsertGas Control System Connected to a Control Valve in a Millivolt SystemWall Switch Wiring the FireplaceFor Standing Pilot Ignition Wiring Appliance Requirements Gas Pressure RequirementsWith the J-BOX Fan Option FB-IN & FB-Grand onlyInstalling Logs and Ember Material Installing Trim SurroundsBefore Lighting the Appliance After the InstallationDouble-check for faulty components Lighting the ApplianceImportant Turn OFF the GAS Before Servicing Your Fireplace Appliance MaintenanceMaintaining and Servicing Your Appliance
Related manuals
Manual 41 pages 37.45 Kb

CFX-Grand-B, FB-Grand, CFX-IN-B, FB-IN specifications

Heat & Glo has long been recognized as a leader in the fireplace industry, offering innovative designs that merge function with luxury. Among their notable offerings are the LifeStyle CFX-Grand-B, CFX-IN-B, FB-IN, and FB-Grand models. Each of these fireplaces is engineered to elevate living spaces while providing efficient heating solutions.

The LifeStyle CFX-Grand-B is a contemporary masterpiece that prioritizes versatility and style. This model features a sleek, linear design that can be customized with various finishes, allowing it to seamlessly fit into any interior decor. A standout feature of the CFX-Grand-B is its innovative multi-sided design, enabling a stunning view from multiple angles. With advanced heat distribution technology, it ensures optimal warmth, demonstrating that elegance can coexist with practicality.

Next in line is the CFX-IN-B, which is perfect for those who want to create a focal point in their home without compromising space. This model boasts an impressive array of customizable options, including media choices like decorative stones and glass. The advanced IntelliFire technology allows for easy operation with a simple remote control or a smart home integration, ensuring comfort at the touch of a button. Additionally, the CFX-IN-B's clean aesthetic and efficient heating capabilities make it an excellent choice for modern living areas.

The FB-IN model caters to traditionalists while incorporating modern efficiencies. It features a classic design with large viewing areas, enabling an unobstructed view of the flames. This fireplace is equipped with a powerful blower system that enhances heat circulation throughout the room, allowing for a cozy atmosphere even during the coldest months. The FB-IN’s robust build quality ensures durability, making it a long-lasting addition to any home.

Lastly, the FB-Grand further exemplifies Heat & Glo’s commitment to luxury and performance. With a wider profile, this fireplace creates an expansive canvas for mesmerizing flames, ensuring it becomes the heart of any room. High-efficiency ratings mean it is not only visually appealing but also economical to operate. The FB-Grand integrates seamlessly with Heat & Glo's customizable framing options, allowing homeowners to design a fireplace that fits their unique style.

In conclusion, each of the Heat & Glo LifeStyle models offers distinct features and technological advancements that enhance home heating and aesthetics. They combine stylish design, efficient heating, and user-friendly technology, making them a top choice for those looking to add warmth and sophistication to their living spaces.
Top Page Image Contents