Holmes HASF1796RC warranty Assembly Instructions, Base / Pole Assembly, Fan Head Assembly

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1)	Read all instructions before using the appliance.
2)	To avoid fire or shock hazard, plug the appliance directly into a 120 V AC
	electrical outlet.
3)	Keep the cord out of heavy traffic areas. DO NOT let the cord hang over
	the edge of a table or counter. To avoid fire hazard, NEVER put the cord
	under rugs, near heat registers, radiator, stoves, or heaters.
4)	To protect against electrical hazards, DO NOT immerse in water or other
	liquids. Do not use near water.
5)	Close supervision is necessary when any appliance is used by or near
	children, or by disabled people.
6)	Always unplug the fan before moving it, putting on or taking off parts,
	cleaning, or whenever the fan is not in use. Be sure to pull by the plug
	and not the cord.
7)	Avoid contact with moving parts. DO NOT operate without fan grills prop-
	erly in place.
8)	DO NOT operate any appliance with a damaged cord or plug, if motor fan
	fails to rotate, after the appliance malfunctions, or if it has been dropped
	or damaged in any manner. Return appliance to manufacturer for
	examination, electrical or mechanical adjustment, or repair.
9)	DO NOT operate in the presence of explosive and/or flammable fumes.
10)	Use appliance only for intended household use as described in this
	manual. Any other use not recommended by the manufacturer may
	cause fire, electric shock, or injury to persons. The use of attachments not
	recommended or sold by The Holmes Group may cause hazards.
11)	DO NOT use outdoors.

ASSEMBLY INSTRUCTIONS

Base / Pole Assembly

Step 1: Push in the small tab on each foot extension and snap into base

Step 2: Remove the base collar from the base by turning counter-clockwise.

Step 3: Take the pole, with the solid end down, and insert it into the base. The hollow end of the pole (with the screw hole) will be facing up.

Step 4: Replace the height adjustment knob over the pole, slide it down

the pole, and secure it to the base by turning clockwise.

Fan Head Assembly

Step 1: Position the rear grill over the motor shaft, making certain the 2 notches at the top and bottom of the rear grill fit over the 2 prongs on the motor housing. Please make sure the rear grill fits securely against the motor housing.

Step 2: Secure the rear grill in its place using the rear grill mounting- ring. Turn this ring clockwise and tighten firmly.

Step 3: Slide the fan blade; with the hollowed interior of the blade fac- ing towards the rear grill firmly onto the motor shaft. Make sure the shaft protrudes from the front of the blade.

Step 4: Secure the fan blade onto the motor shaft by turning the fan blade cap in a counter-clockwise direction until it is firmly in place.

Step 5: Prepare the front grill by simply snapping the circular front grill logo plate in place.

Step 6: Center the front grill by aligning the Holmes logo so it is hori- zontal and parallel to the floor. Place the front grill on to the rear grill and snap into place. Tighten the securing screw at the bottom of the front grill.

12)	Always use on a dry, level surface.
13)	Keep unit away from heated surfaces and open flames.
14)	WARNING: To reduce the risk of fire or electric shock, DO NOT use this fan
	with any solid-state speed control device.
15)	DO NOT attempt to repair or adjust any electrical or mechanical functions
	on this unit. Doing so will void your warranty. The inside of the unit con-
	tains no user serviceable parts. All servicing should be performed by
	qualified personnel only.

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC (Alternating Current) PLUG (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact qualified personnel to install the proper outlet.

DO NOT DEFEAT THE SAFETY PURPOSE OF THIS

POLARIZED PLUG IN ANY WAY

A B C D

A.LOGO PLATE

B.FRONT GRILL

C.FAN BLADE CAP

D.FAN BLADE

E.REAR-GRILL MOUNTING RING

F.REAR GRILL

G.MOTOR SHAFT

H.MOTOR HOUSING

I.OSCILLATION KNOB

J.NECK

K.TILT-ADJUSTMENT KNOB

L.1TOUCH™ FRONT HOUSING

M.1TOUCH™ REAR HOUSING

N.THUMBSCEW

O.POLE

P.HEIGHT ADJUSTMENT KNOB

		G	H
			I
			J
			K
E			N
U	F		M
		L
	O		T
		P
		Q	S

Q. BASE R

R.FEET (4)

S.POWER CORD

T.REMOTE CONTROL

U. SECURITY SCREW FIGURE 1