Jet Tools AFS-1000B Operating the TOOL. Learn the tool’s, Keep Guards in Place and in working

	WARNING
1.	FOR YOUR OWN SAFETY, READ	16. DISCONNECT TOOLS before servicing
	INSTRUCTION MANUAL BEFORE	and when filters.
	OPERATING THE TOOL. Learn the tool’s	17. USE RECOMMENDED ACCESSORIES.
	application and limitations as well as the	The use of accessories and attachments not
	specific hazards peculiar to it.	recommended by manufacturer may cause
2.	KEEP GUARDS IN PLACE and in working	hazards or risk of injury to persons.
	order.	18. AVOID ACCIDENTAL STARTING. Make
3.	ALWAYS WEAR EYE PROTECTION.	sure switch is in “OFF” position before
4.	GROUND ALL TOOLS. If tool is equipped	plugging in power cord.
	with three prong plug, it should be plugged	19. NEVER STAND ON TOOL. Serious injury
	into a three-hole electrical receptacle. If an	could occur if the tool is tipped or if the fan
	adapter is used to accommodate a two	blade is accidentally contacted.
	prong receptacle, the adapter lug must be	20. CHECK DAMAGED PARTS. Before further
	attached to a known ground. Never remove	use of the tool, a guard or other part that is
	the third prong.	damaged should be carefully checked to
5.	KEEP WORK AREA CLEAN. Cluttered	ensure that it will operate properly and
	areas and benches invite accidents.	perform its intended function-check for
6.	DON’T USE IN DANGEROUS	alignment of moving parts, binding of
	ENVIRONMENT. Don’t use power tools￿in	moving parts, breakage of parts, mounting,
	damp or wet locations, or expose them to	and any other conditions that may affect its
	rain. Keep work area well-lighted.	operation. A guard or other part that is
7.	KEEP CHILDREN AND VISITORS AWAY.	damaged should be properly repaired or
		replaced.
	All children and visitors should be kept a
		21. NEVER LEAVE TOOL RUNNING
	safe distance from work area.
8.	MAKE WORKSHOP CHILDPROOF. Use	UNATTENDED. TURN POWER OFF.
		Don’t leave tool until it comes to a complete
	padlocks, master switches, or remove
		stop.
	starter keys.
		22. DRUGS, ALCOHOL, MEDICATION. Do not
9.	DON’T FORCE TOOL. It will do the job
		operate tool while under the influence of
	better and be safer at the rate for which it
		drugs, alcohol or any medication.
	was designed.
		23. MAKE SURE TOOL IS DICONNECTED
10.	USE RIGHT TOOL. Don’t force tool or
		FROM POWER SUPPLY while motor is
	attachment to do a job for which it was not
		being mounted, connected or reconnected.
	designed.
		24. WARNING: Some dust created by power
11.	WEAR PROPER APPAREL. No loose
		sanding, sawing, grinding, drilling and other
	clothing, gloves, neckties, rings, bracelets,
		construction activities contains chemicals
	or other jewelry to get caught in moving
		known to cause cancer, birth defects or
	parts. Nonslip footwear is recommended.
		other reproductive harm. Some examples of
	Wear protective hair covering to contain long
		these chemicals are:
	hair.
		• Lead from lead based paint
12.	ALWAYS USE SAFETY GLASSES. Wear
		• crystalline silica from bricks and cement
	safety glasses (must comply with ANSI
	Z87.1). Everyday eyeglasses only have	and other masonry products, and
	impact resistant lenses; they are not safety	• arsenic and chromium from chemically-
	glasses. Also use face or dust mask if	treated lumber.
	cutting operation is dusty.	25. Your risk from those exposures varies,
13.	SECURE WORK. Use clamps or a vise to
		depending on how often you do this type of
	hold work when practical. It’s safer than	work. To reduce your exposure to these
	using your hands and frees both hands to	chemicals: work in a well ventilated area,
	operate tool.	and work with approved safety equipment,
14.	DON’T OVERREACH. Keep proper footing	such as those dust masks that are
	and balance at all times.	specifically designed to filter out microscopic
15.	MAINTAIN TOOLS IN TOP CONDITION.	particles
	Keep tools sharp and clean for best and
	safest performance. Follow instructions for
	lubricating and changing accessories.

3