Enerco HS4040 Electrical, Thermostat & Location, Ventilation, Operations, Cleaning Information

Page 4

a separate regulator must be installed ahead of the heater. Refer to Figure 2 for maximum allowable pres- sure for stated model and gas.

See heater rating plate for minimum gas supply pres- sure “For the Purpose of Input Adjustment”

On a multiple heater installation it may be possible to use one large capacity regulator or an individual regula- tor for each heater. Nevertheless, it is recommended practice to make the entire pipe system a loop. Contact your local representative or the factory for proper gas pressure reducing design stage.

WARNING: DO NOT EXCEED ½ P.S.I. INLET PRES- SURE TO HEATERS SHOWN IN FIGURES 1 AND 2

6. ELECTRICAL

All external wiring must be in accordance with the existing electrical code. Use wiring diagram furnished with heater. Be sure electric supply characteristics match those called for on the name plate. The unit must be electrically grounded in accordance with the National Electrical Code, ANSI/NFPA70, latest revision. In Canada refer to Canadian electrical code CSA C22.1

7. THERMOSTAT & LOCATION

Make sure that the electrical characteristics of the thermostat match those of the heater controls. For best results thermostat should be positioned 5 ft. above floor where air can circulate freely around it. DO NOT MOUNT directly to cold-side wall, in direct drafts or directly beneath the infra-red heater.

8.VENTILATION

a.The minimum intake and exhaust air openings shall pro- vide for not less than 400 CFM for every 100,000 BTU input except that the infiltration area may be included in the intake area. The exhaust fan must be interlocked with the heater thermostat. If a power exhaust fan

is used, it should be controlled by the thermostat or humidistat

Figure 2

b.Where natural (gravity) ventilation is provided for exhaust, the openings must be distributed above the heaters (preferably at the peak of the roof) and the areas of openings shall not be less than 300 square inches for every 100,000 BTU input.

9. OPERATIONS

Upon completion of electrical wiring, gas piping and purging of gas lines to heaters, refer to the lighting instruction plate attached to heater for proper lighting procedure.

10. CLEANING INFORMATION

Blow out Venturi and burner face with compressed air (25# max. pressure); also clean orifices (see Figure 2 for correct size drill). For detailed maintenance and cleaning instructions contact your local representative or factory.

WARNING: GASKET BINDER MATERIAL USED IN THIS HEATER ASSEMBLY WILL TEMPORARILY EMIT AN ODOR AND/OR VAPOR. USE VENTILATION (a OR

b)AND THIS CONDITION WILL CLEAR UP IN APPROXI- MATELY 20 MINUTES AND WILL NOT REOCCUR.

WARNING: DO NOT ATTEMPT TO IGNITE THE PILOT BY HAND ON HEATERS EQUIPPED WITH AUTO- MATIC spark ignition.

WARNING: THE STATE OF CALIFORNIA REQUIRES THE FOLLOWING WARNING: COMBUSTION BY-PROD- UCTS PRODUCED WHEN USING THIS PRODUCT CON- TAIN CARBON MONOXIDE, A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS (OR OTHER REPRODUCTIVE HARM).

NOTE: USE LATEST EDITION FOR ALL ANSI STAN- DARD AND CANADIAN STANDARDS.

MODEL

BTU/HR. RATING

 

 

 

GAS SUPPLY PRESSURE (W.C.)

 

 

ORIFICE SIZE

 

 

 

 

 

 

 

 

 

 

 

 

GAS

 

MIN.

 

 

MAX.

 

MANIFOLD

NO.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NATURAL

PROPANE

NAT.

 

L.P.

 

NAT.

 

L.P.

 

NAT.

L.P.

NAT.

L.P.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4030

30,000

30,000

6.6”

 

11”

 

14”

 

14”

 

5.6”

10”

43

52

4040

40,000

40,000

6.8”

 

11”

 

14”

 

14”

 

5.8”

10”

37

49

8050

50,000

50,000

7.0”

 

11”

 

14”

 

14”

 

4.3”

10”

30

45

8060

60,000

60,000

7.0”

 

11”

 

14”

 

14”

 

5.8”

10”

29

43

8070

70,000

–

7.0”

 

–

 

14”

 

–

 

6.0”

–

28

–

9080

80,000

80,000

7.0”

 

11”

 

14”

 

14”

 

5.8”

10”

37

49

9090

90,000

90,000

7.0”

 

11”

 

14”

 

14”

 

5.0”

10”

32

47

9100S

100,000

100,000

7.0”

 

11”

 

14”

 

14”

 

5.0”

10”

31

46

9100

100,000

100,000

7.0”

 

11”

 

14”

 

14”

 

4.3”

10”

30

45

9120

120,000

120,000

7.0”

 

11”

 

14”

 

14”

 

5.8”

10”

29

43

9140

140,000

–

7.0”

 

–

 

14”

 

–

 

5.5”

–

28

–

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Enerco Group, Inc. Gas-Fired Infra-Red Space Heaters

4

Operating Instructions and Owner’s Manual

Page 3 Page 5
Image 4
Page 3 Page 5
Contents SHEATSTAR High-Intensity Infrared Heaters eld Contents Carbon Monoxide PoisoningGeneral Information SuspensionGAS Supply GAS PressureCleaning Information ElectricalThermostat & Location VentilationMeans of Proving Adequate Grounding Area Connection DiagramMaximum Combined Load 1.5 AMP Stock Description Req’d 00435 a Reflector Assembly 02523 a Description Req’d 00442 a Reflector Assembly 02524 a03397 P Venturi Orifice Br. N.GPage 9100S Nat. Gas Stock Description REQ’D Ignition Control #SP715ASWC Control ASSY. NDSP-5Replacement Parts List for Control System Suffix LA5 For Heat Star Series 4000COMB. GAS Valve PP NG NPTThermostat PP Heat Star Pilot BURNER-9000HTRTypical Wall Mount High Altitude Operation See for proper inlet pressuresRigid or flexible gas Pipe nipple Line to heaterThis page Intentionally Qualified Service Agency For Information Regarding ServiceEmail to techservice@enerco-mrheater.com Or direct from the factoryCaus EZQIntentionnellement Lancb Standard InstallationUtilisation YP E DistancesOntale Ationfix Hori NPP CommandeListe Ystmeè Liste CommandeYstmeè Liste Ystmeè Liste DE P Liste DE PNdsp Scriptide Référ NCE14639 1236606398 03421Central Support Venturi Collecteur 06396 Ajutage9100 05430 Ajutage Brûleur 9120 05429 AjutageVenturi 03421 Brûleur Réflecteur 00442Darticle Nº Venturi AjutageRaccordement Ndsp AV.CEtdegaz EN Opti onTerre Raccordement DE DiagrammeRemarque Comment CIRCUIT.6 YageRemarque UTILISATION.9ALIMENTATION.4 EN G a Z DISTANCES.2TA BLE DAN GERErtissementav ErtissementavMédiatement Dappareildecetype

HS8060, HS9120, HS9100S, HS4040 specifications

The Enerco HS9100S, HS9120, HS4040, and HS8060 are a range of high-performance space heaters designed to provide efficient heating solutions for various applications. Each model comes with specific features and technologies that cater to different heating needs while ensuring energy efficiency and user comfort.

The HS9100S is renowned for its robust build and powerful heating capacity. With a heat output of up to 9,000 BTUs, it effectively warms up spaces in a matter of moments. One of its standout features is the precise thermostat control that allows users to set their desired temperature easily. Additionally, the HS9100S has a safety shut-off system that activates in case of overheating, making it a dependable choice for homes and garages.

The HS9120 model builds on the features of the HS9100S while integrating advanced infrared technology. This unit not only heats the air but also warms objects and people in the room, creating a more comfortable environment. With a sleek design, the HS9120 is both practical and aesthetically pleasing. The adjustable heat settings provide versatility, enabling users to customize their heating experience based on different conditions.

The HS4040 is tailored for those seeking portability without sacrificing performance. Weighing significantly less than its counterparts, this model is easy to move between locations, making it ideal for workshops or outdoor use. The HS4040 features a built-in handle and compact design for enhanced mobility. Despite its smaller size, this unit delivers an output of up to 4,000 BTUs and includes a reliable safety feature to prevent accidental ignition.

Lastly, the HS8060 stands out for its user-friendly interface. It includes an LED display that provides real-time temperature readings, along with a remote control option for added convenience. The HS8060 model is equipped with energy-saving modes, allowing for reduced power consumption when heating is not required at full capacity. Its versatile design makes it suitable for any room, including living spaces and office areas.

In summary, the Enerco HS9100S, HS9120, HS4040, and HS8060 represent a commitment to quality and efficiency in portable heating solutions. Each model offers its unique set of features, making them suitable for a range of heating applications, ensuring warmth and comfort during cold months. With a focus on safety, efficiency, and user convenience, these units are excellent choices for anyone seeking reliable heating options.
Top Page Image Contents