Lennox Hearth 1003C operation manual Combustible Wall Clearances

Page 6

PLANNING YOUR INSTALLATION

COMBUSTIBLE WALL CLEARANCES

WARNING: IT IS VERY IMPORTANT THAT YOU OB- SERVE THE MINIMUM CLEARANCES.

There are listed clearances for your stove which were deter- mined in a Laboratory test using various "classes" of stove pipe or chimney. Minimums are first established for the stove itself and increased based on how much heat is transferred by each class of pipe.

NOTE: Manufactured (mobile) home installations require the use of a Type L-Vent Chimney connector only. Use of a single wall flue pipe connection is not permitted.

Manufactured (Mobile) Home Standard and Residential Reduced - Using 6” (152 mm) diameter Type L-Vent connector pipe (to the top of the stove) with listed factory-built 103HT chimney suitable for use with solid fuels or a code approved masonry chimney. Approved brands of factory built chimney are Dura-Vent, Security, Jake Evans and Metal Bestos.

MANUFACTURED (MOBILE) HOME INSTALLATIONS MUST BE EQUIPPED WITH A RAIN CAP AND SPARK ARRESTOR.

Clearances (inches / millimeters)

A. 14 / 356

C. 17

/ 432

E. 16 / 406

B. 25 / 635

D. 9 /

229

F. 8 / 203

Residential Standard (not approved for manufactured [mobile] homes) Using 6” (152 mm) diameter, single wall connector pipe with listed factory-built to the top of the stove.

Clearances (inches / millimeters)

 

A. 22 / 559

C. 25 / 635

E. 16 / 406

B. 25.5 / 648

D. 16 / 406

F. 15 / 381

Residential Note: Approved for 6” (152 mm) diameter, single wall, minimum 24 MSG black or blued steel con- nector pipe with listed factory-built 103HT chimney suitable for use with solid fuels or a code approved masonry chimney.

Manufactured (Mobile) Home Reduced and Residen- tial Reduced Using 6” (152 mm) diameter Type L-Vent connector pipe (to the top of the stove) with listed fac- tory-built 103HT chimney suitable for use with solid fuels or a code approved masonry chimney. Approved brands of factory built chimney are Dura-Vent, Security, Jake Evans and Metal Bestos. MANUFACTURED (MOBILE)

HOME INSTALLATIONS MUST BE EQUIPPED WITH A RAIN CAP AND SPARK ARRESTOR. Alcove size: 84” (213 cm) minimum height, 56” (143 cm) minimum width, and 24” (610 mm) maximum depth.

Clearances (inches / millimeters)

 

A. 11 / 280

C. 14.5

/ 369

E. 16 / 406

B. 25.5 / 648

D. 5.5 /

140

F. 5.5 / 140

Vent Height (all installations) - The pipe should extend 12 feet above the stove top, as a minimum, to achieve a stable draft.

Corner Installation

C

45°

F

Parallel Installation

A D

B

E

PAGE 6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents EPA Certified Catalytic Wood Burning Stove 775003M, Rev. P, 11/03Important Warnings Table of Contents Planning Your Installation Smoke DetectorsSelecting a Location Canada Requirements Floor ProtectionUSA Requirements Standard Parallel Hearth PAD ShownCombustible Wall Clearances Alcove Clearances Reduced Masonry Structure Clearance AlcoveProtected Wall Clearance Outside AIR InstallationAIR Intake Cover Stove Outside Air Floor Duct Floor ProtectorGrounding Stove Acceptable Connector Pipe for INSTALLA- TionsSecuring the Stove to the Floor Remove ASH Drawer ClipChimney Height Requirements Chimney InspectionVapor Barrier At Chimney Penetration 2’ by 10’ Rule for Vent TerminationDraft Test Procedure Draft RequirementsManufactured Mobile Home Standard Using 6 152 mm Diameter Type L-Vent Connector PipeResidential Standard Important NotesWall pass-through with a minimum 9 228.6 mm air space be Sides, to maintain the 9 228.6 mm air space. When fasteningMethod B 228.6 mm Clearance to Combustible Wall Member Inside wall of the Solid-Pak chimney. The inner endCare and OPERATI0N Care and Operation Fuel DoorGlass HOW to Start and Maintain a Fire BREAK-IN PeriodBypass Damper Control Catalytic Temperature ProbeRefueling Burn Recommended FuelMaintenance FuelDoor / Glass Gasket and ASH Drawer GAS- KET Replacing GlassCatalyst Replacement Side Cut-Away View of FireboxTroubleshooting Catalyst Substrate Cracking Catalyst PluggingCatalyst Deactivation Catalyst SubstrateOverfiring Caused From Improper Installation Overfiring DamageOverfiring Caused From Improper Operation Specifications Model 1003C Fire Box Size Cubic feetItem no Description Replacement Parts List Model 1003C Damper Assembly Catalytic Combustor System ComponentsBlower Kit BK-100 Outside Air Floor Duct OAFD-SStove-Stat Kit SSK Variable Speed Control, Dial-A-TempSAFETY/LISTING Label EPA Label Service and Maintenance LOG Ownership RecordsWest Taft Avenue Orange, CA
Top Page Image Contents