Lennox Hearth MPE-36R warranty Pre-Installation

Page 5

Fireplace specifications

Cat. No. H1534

Model: MPE-36R

Description: Merit Plus Electric Fireplace, 36” Radiant

Shipping Weight: 90 lb.'s (41 KG) Packaging:

44-3/4” x19-1/2” x 34-1/4”

(1135 mm x 495 mm x 870 mm)

17.30cu. ft.

Power Requirements: (120 Volt, 60 Hz.)

Rated Wattage - 1600 Watts Amperage - 13.33 Amps

(240 Volt, 60 Hz.)

Rated Wattage - 3000 Watts Amperage - 12.5 Amps

Blower CFM: 83 CFM

(120 V): 5,461 BTU/HR

(240 V): 10,239 BTU/HR

Minimum Clearances to Combus- tibles

This appliance is a zero-clearance design and is approved to be framed in with combustible materials (up to the edge of the appliance). A drywall lip at the top of the fireplace and 4 nailing flanges on the sides of the appliance is provided to facilitate installation.

 

Clearances

 

 

 

Sides

 

0 inches - 0 mm

Floor

 

0 inches - 0 mm

 

 

 

Top

 

0 inches - 0 mm

Table 2

 

 

Mantel Clearance: Combustible and Non-com- bustible mantels may be installed at any height above the top of the face of fireplace.

Hearth Protection: A hearth is not mandatory, but it is recommended for aesthetic purposes. Secure the hearth extension to the floor to prevent possible shifting. Do no block the air- flow beneath the appliance (read the following WARNING).

PRE-INSTALLATION

Before You Start

Check appliance for any concealed damage.

Detailed Installation Steps

1.Complete the framing opening to the dimen- sions specified in Figure 2.

2.Prepare the connections to power source: 120 Volt Connections - Locate the power cord on the left side of the unit and connect it to the outlet installed during the framing (see Figure 2). Verify that the power to the receptacle is off.

Hard wired installation:

Ensure that there is a minimum of 8" of the service cable for connection to the junction box on the fireplace.

-Loosen four screws to remove the junction box cover plate.

-Disconnect and remove the 120 Volt power cord from the fireplace wires.

-Position the fireplace into the framed-in opening. Attach fireplace to frame using nailing flanges provided.

-Complete the wiring to the fireplace as shown on Page 10.

-Place all wire connectors inside the junction box.

-Attach junction box cover plate with four screws.

240 Volt Connections - Ensure that there is a minimum of 8" of the service cable for connection to the junction box on the fireplace.

-Loosen four screws to remove the junction box cover plate.

-Disconnect and remove the 120 Volt power cord from the fireplace wires.

-Position the fireplace into the framed-in opening. Attach fireplace to frame using nailing flanges provided.

-Complete the wiring to the fireplace as shown on Page 11.

-Place all wire connectors inside the junction box.

-Attach junction box cover plate with four screws.

The fireplace wires L1, L2, N, N1, N2 and G are attached to the rear of the junction box cable clamp for easy access.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

3.Wire a dedicated, properly fused circuit with an Amp rating for the appropriate voltage (120 V - 15 Amps or 240 V - 20 Amps). A dedicated circuit is required to prevent overloading a house circuit in cases of having multiple appliances on the same circuit. Use an outlet that is protected by a ground fault circuit interrupter where required by electrical code.

4.(If applicable) Make wall mount wall switch or wall thermostat connections as outlined on Pages 11 & 12.

5.Perform a function test. See Manual Control Panel Operation on Page 6 and Remote Control Operation on Page 7.

Electrical connections

Refer to the electrical diagrams on Pages 10

to 14.

WARNING

Electrical wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electrical shock and injury to individuals.

IMPORTANT

Any electrical re-wiring of this appliance must be done by a qualified electrician.

WARNING

Do not use this fireplace if any part of it has been underwater. Immediately call a qualified service technician to inspect the fireplace and replace any part of the electrical system which has been under water.

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Report # C1482763 Electric Fireplace 775,172M REV. G 04/2007Do not Block Airflow AT the Bottom AIR Intakes Important Safety and Warniing Information Congratulations Fireplace specifications Framing SpecificationsLeft Side Top ViewPRE-INSTALLATION Flame / Ember On/Off front most switch Manual control Panel Main Power On/Off rear most switchFinal Finishing BREAK-IN PeriodRemote Control Operation Cleaning the Glass Enclosure Panel optional kit MaintenanceHEATER/BLOWER Replacement PROCE- Dure Brick Panel Removal ProcedureAccess bulbs as follows Bulb Replacement ProcedureReplacing Light Bulbs Ember BedGround 120 v 1600 w Wiring Diagram 120 voltWiring 120 volt Ground Wiring 240 voltGround 240 v 3000 w GroundInside Outside Wall Thermostat & Wall Switch Wiring DiagramsOptional kits, see Inside OutsideWall Thermostat Wall Thermostat Wiring 24 VACBlack White White Left Side FireplaceRed Wire the wall switch prior to installing the fireplaceWall Switch Wiring 24 VAC Action Symptom Possible CausesCorrective Action Description Mpe-36r Cat. No Qty Replacement PartsReplacement Parts component diagrams Mpe-36r Wall Switch Kit Accessory ComponentsWall Thermostat Trim KitPage 775,172M REV.G 04/2007
Related manuals
Manual 18 pages 47.46 Kb

MPE-36R specifications

The Lennox Hearth MPE-36R is an innovative gas fireplace that exemplifies both modern aesthetics and cutting-edge technology. Designed to enhance any living space, this fireplace model combines efficiency and elegance, making it a popular choice among homeowners looking to create a cozy atmosphere.

One of the standout features of the MPE-36R is its realistic flame technology. The fireplace employs advanced burner technology that produces a beautiful, lifelike flame effect, simulating the flickering light and warmth of a traditional wood-burning fire. The adjustable flame height allows users to customize the ambiance to their preference, whether for a romantic evening or a lively gathering.

The MPE-36R also boasts a high-efficiency rating, ensuring that heat is effectively distributed throughout the room without wasting precious energy. It is designed with an insulated firebox, which aids in retaining heat and maximizing output. This efficiency not only contributes to lower energy bills but also makes it an environmentally friendly option for heating your home.

Another notable characteristic of the MPE-36R is its sleek design. The fireplace features a contemporary frame that can seamlessly blend into various interior styles, from modern to traditional. Optional aesthetic enhancements, such as decorative fire glass and logs, allow homeowners to personalize the look, making it a centerpiece in any room.

Incorporating smart technology, the MPE-36R can accommodate remote and Wi-Fi controls, ensuring that users can operate it effortlessly. This feature provides the convenience of adjusting the flames, heat settings, and even the timer from the comfort of their couch or via a smartphone app.

Safety is paramount, and the MPE-36R is equipped with several features to ensure peace of mind. The fireplace includes a safety shut-off system, which automatically turns off the unit in the event of a malfunction. Additionally, the glass front remains cool to the touch, significantly reducing the risk of burns, especially in homes with children or pets.

With its combination of exquisite design, efficiency, advanced technology, and safety features, the Lennox Hearth MPE-36R is a sophisticated choice for anyone looking to add warmth and style to their home. Perfect for both new constructions and renovations, it stands out as a leading option in the world of modern gas fireplaces.
Top Page Image Contents