Suggested Specifications

Large Volume Power Burner: Gas, Oil & Dual Fuel Commercial Water Heaters

TITANTM LV POWER GAS (MODELS TPG)

Water heater(s) shall be Model___________________as manufactured by State Water Heaters or an approved equal. Water heater(s) shall be of glass-lined design

and include a powered gas burner with electronic ﬂame safeguard, intermittent ignition, main and pilot automatic gas valves, redundant solenoid gas valve, gas pressure regulator, diaphragm air switch for proof of blower operation, and ﬂame inspection port. Maximum supply gas pressure to heater 13˝ W.C. Heater(s) shall have an input rating of ____________ and a recovery rating of ________ GPH at a temperature rise of 100°F with a minimum actual storage capacity of ________. Heater(s) shall

be equipped with _______ NPT water inlet and outlet openings, (2) 3˝ handhole cleanouts, shall have an ASME working pressure of 160 psi, and stamped National

Board, and listed by Underwriters Laboratories. Controls shall include: high temperature limit control (manual reset), upper and lower thermostats, combination temperature and pressure gauge, low water cutoff, ASME rated temperature relief valve, drain valve and draft regulator. Control compartment door shall be hinged for easy access. The heater(s) shall be equipped with multiple anodes for cathodic protection. The heater(s) shall be insulated with high-density foam insulation. Heater(s) must meet or exceed current ASHRAE/IES 90.1-1999 for recovery efﬁciency and standby loss. The outer jacket shall have a baked powder coat ﬁnish. All internal surfaces of the heater(s) exposed to water shall be glass-lined with an alkaline borosilicate, nickelous oxide composition that has been fused to steel by ﬁring at a temperature range of 1400°F to 1600°F. Heater(s) tank shall have a 3, 5, or 10 year limited warranty against corrosion as outlined in the written warranty. Professional start-up service to be included.

SUGGESTED SPECIFICATIONS

TITANTM LV POWER LOW NOX (MODELS TPX)

Water heater(s) shall be Model___________________as manufactured by State Water Heaters or an approved equal. Water heater(s) shall be of glass-lined design

be equipped with _______ NPT water inlet and outlet openings, (2) 3˝ handhole cleanouts, shall have an ASME working pressure of 160 psi, ASME stamped and listed

by Underwriters Laboratories. The water heater shall be approved for low NOx and meet or exceed California rule 1146.2. The unit shall provide modulating ﬁre for smooth system operation and precise temperature control. Controls shall include: high temperature limit control (manual reset), upper and lower thermostats, modulating control, combination temperature and pressure gauge, low water cutoff, ASME rated temperature relief valve, drain valve and draft regulator. Control compartment door shall be hinged for easy access. The heater(s) shall be equipped with multiple anodes for cathodic protection. The heater(s) shall be insulated with high-density foam insulation. Heater(s) must meet or exceed current ASHRAE/IES 90.1-1999 for recovery efﬁciency and standby loss. The outer jacket shall have a baked powder coat ﬁnish. All internal surfaces of the heater(s) exposed to water shall be glass-lined with an alkaline borosilicate, nickelous oxide composition that has been fused to steel by ﬁring at a temperature range of 1400°F to 1600°F. Heater(s) tank shall have a 3, 5, or 10 year limited warranty against corrosion as outlined in the written warranty. Professional start-up service to be included.

SUGGESTED SPECIFICATIONS

TITANTM LV POWER OIL AND DUAL FUEL (MODELS TPO AND TPD)

Water heater(s) shall be Model_____________________as manufactured by the State Water Heaters or an approved equal. Heater(s) shall have a minimum oil ﬁring

rate of_____gallons per hour, an input rating of____________BTU/HR. The heater(s) shall have a recovery rate of_____GPH at a 100°F rise and a storage capacity

of______gallons. The 160 psi design pressure tank shall be glass-lined with an alkaline borosilicate composition and fused to the steel by ﬁring at 1600°F. The heater(s)

shall be equipped with______NPT water inlet and outlet openings, (2) 3˝ handhole cleanouts, and carry a National Board stamping. The heater(s) shall be ASME and the

entire unit listed by Underwriters Laboratories. Controls shall include: high temperature limit control (manual reset), upper and lower thermostats, combination temperature and pressure gauge, low water cutoff, ASME rated temperature and pressure relief valve, and barometric draft regulator. Control compartment door shall be hinged for easy access and include cam locks for security. The heater(s) shall be equipped with multiple anodes for cathodic protection. The heater(s) shall be insulated with high-density foam insulation and meet or exceed current standard of ASHRAE 90.1-1999 for standby loss and recovery efﬁciency. The heater(s) shall include a drain valve and ﬂame observation port. The jacket shall be baked powder coat ﬁnish. Heater(s) vessel shall have a 3, 5 or 10 year limited warranty against failure as outlined in the written warranty.

The TPO models shall have a UL listed burner with two-stage pump, oil safety valve, electronic ﬂame safeguard, intermittent ignition and diaphragm air switch for proof of ﬂame operation.

The TPD models shall include a dual fuel burner with two-stage oil pump, oil safety valve, electronic ﬂame safeguard, intermittent ignition, diaphragm air switch, main and pilot automatic gas valves, gas pressure regulator and manual crossover switch.

In keeping with our policy of continuous product improvement, speciﬁcations are subject to change without prior notice.

COMMERCIAL 500 Lindahl Parkway, Ashland City, TN 37015 • www.statewaterheaters.com Printed in U.S.A.

The Expert’s Choice®

STPBGODF/1003

Oil & Dual Fuel Commercial Water Heaters, Gas specifications

State Industries has long been a trusted name in the water heating industry, providing innovative and efficient solutions for both residential and commercial applications. Among its impressive lineup, the gas, oil, and dual fuel commercial water heaters stand out for their exceptional performance, reliability, and versatility. These units are designed specifically to meet the demanding requirements of commercial establishments such as restaurants, hotels, and hospitals.

One of the standout features of State Industries’ commercial water heaters is their energy efficiency. Many models incorporate advanced insulation technologies, allowing for minimal heat loss and lower energy consumption. The use of high-efficiency burners and innovative heat exchanger designs boosts thermal efficiency, translating to significant savings in operational costs for businesses.

State’s gas water heaters are engineered to deliver robust performance with quick recovery rates, ensuring a constant supply of hot water. They utilize state-of-the-art combustion technology to provide reliable heating while adhering to stringent emissions regulations. The oil-fired models also present impressive performance characteristics, with high heat output and the ability to operate in regions where natural gas is not accessible.

The dual fuel commercial water heaters are particularly remarkable as they offer flexibility for users who want the option to switch between gas and oil fuel sources. This adaptability is a vital feature for businesses that may experience fluctuating fuel prices or supply constraints. Users can select the optimal fuel based on current market conditions or availability, ensuring continued operation and cost-effectiveness.

Among other characteristics, State Industries units are designed with longevity in mind. The tanks are often constructed from durable materials that withstand the rigors of commercial use. Additionally, many models are equipped with features such as anode rods to combat corrosion, further extending their lifespan.

Advanced control systems are another highlight, allowing for precise temperature management and easy monitoring. These intuitive controls increase operational efficiency and enhance user experience.

In conclusion, State Industries' gas, oil, and dual fuel commercial water heaters are an outstanding choice for businesses seeking reliable, efficient, and flexible water heating solutions. Their combination of advanced technology, energy efficiency, and robust construction ensures that they meet the diverse needs of the commercial sector. Whether for cooking, cleaning, or sanitation, these water heaters stand ready to deliver.

State Industries Gas warranty Suggested Specifications, State Water Heaters