Troubleshooting

It is rare that any of these problems occur but if they do here are some things to try.

HUM - Try a mains ground adapter if they are legal in your country. They are also called 3 pin to 2 pin adapters or "cheaters" and are available in hardware stores. There should be one ground in your system and only one. If two or more pieces of gear have 3 pin AC cables a ground loop can occur which will usually cause hum. The preamplifier is probably the best grounded single piece as it is the center of your system.

HISS - Throw the MUTE switch and listen. Did the hiss stop? If so, then the source of the hiss is UPSTREAM from the amplifiers, being generated by your preamps or source components. Some amount of hiss is to be expected from any gear that is amplifying. If the noise level stayed the same when you engaged the MUTE switch, and it is too hissy for you, then try replacing the 12AT7 input tube with a quieter one.

BALANCE - The two speakers sound different - It may be the CD or source and the way it was recorded. First try a different source. Next try swapping the inputs. MUTE your amps and swap left and right inputs. If it is the source, then the problem will "follow" the swap. Return them to normal (L=L). Power down the amps and next try swapping the speaker connections by putting the left speaker wire in the right terminals and right wires into the left terminals. If the problem switched sides then one monoblock is suspect; if the problem stayed on the same side it is probably a damaged or fatigued speaker.

NO SOUND, NO PILOT LIGHT, TUBES DARK- Check AC Mains fuse on back panel. Check AC power cord. Is the amp plugged into a working electrical outlet? (this has happened to everyone at least once).

NO SOUND , PILOT LIGHT ON, TUBES LIT- Check speaker connection and input connection (exchange with the other channel). Take a bias measurement- do all bias test points read zero volts? If so, the B+ fuse is blown. CAREFULLY INSPECT ALL OUTPUT TUBES BEFORE REPLACING FUSE. (See also "Replacing Tubes").

ONE OUTPUT TUBE WILL NOT BIAS- If the bias voltage one one tube will not adjust at all or reads zero volts, first replace the tube. If the reading still is way off or reads zero, turn the amplifier off. Set your multimeter to "ohms" instead of "DC volts". Now measure the bias test point- it should read approximately 10 ohms. If it reads very high or not at all, then the 10 ohm cathode resistor connected to the tube is burned open.This resistor is the final safety valve in case of a shorted output tube, and prevents damage to the rest of the amplifier should this occur. Replacing this resistor can be done by anyone with adequate soldering skills; we recommend contacting our service department here at the factory for specific instructions.

AMPLIFIERS specifications

Manley Labs, a renowned name in high-fidelity audio equipment, has established a reputation for its premium amplifiers, celebrated for their exceptional sound quality and innovative design. With a commitment to craftsmanship and the integration of cutting-edge technology, Manley amplifiers cater to audiophiles and professionals alike, delivering a listening experience that is both immersive and authentic.

One of the hallmark features of Manley amplifiers is their use of high-quality vacuum tubes in many of their models. The warmth and richness that tubes impart to the audio signal are particularly appealing to music lovers who seek a classic analog sound. Models like the Manley Stingray and the Manley 300B offer a distinctive tonal character, allowing musicians and listeners to experience the nuances of recordings as intended by the artists.

In addition to tube technology, Manley amplifiers frequently incorporate advanced solid-state circuitry, striking a balance between traditional warmth and modern reliability. The Manley Reference Amplifier exemplifies this hybrid approach, featuring a robust power supply and precision engineering that ensures a clean, dynamic sound. This versatility allows the amplifiers to perform beautifully in various listening environments, from home setups to professional studio applications.

Manley Labs is also notable for its attention to build quality. The amplifiers are crafted in the USA, utilizing high-grade components and rigorous quality control processes. This commitment to craftsmanship means that every unit is built to last, ensuring long-term reliability and performance. The aesthetic appeal of Manley amplifiers, with their distinctive vintage-inspired designs and premium finishes, further enhances their desirability.

Another key characteristic of Manley amplifiers is their versatility in handling various types of audio signals. Models like the Manley Neo-Classic 300B can accommodate both low-impedance and high-efficiency speakers, making them suitable for a wide range of setups. Additionally, features such as customized input and output transformers help to optimize the performance for different audio sources.

In conclusion, Manley Labs amplifiers embody a blend of vintage charm and contemporary engineering. Their proprietary tube designs, robust solid-state options, and unwavering quality make them a standout choice for anyone seeking an exceptional audio experience. Whether in a casual listening room or a high-end studio, Manley amplifiers promise to deliver richness, clarity, and a connection to the music that transcends the ordinary.