Bias Procedure

The Manley 250 & 500 watt Amplifiers use a fixed bias system that requires very little attention. The term "bias" as used here refers to an externally adjustable voltage applied to each of the output tubes grids. This voltage sets the correct current draw for each output tube. Proper adjustment ensures the best sonic performance and longest tube life. We recommend that you check the bias upon initial receipt of the amps, and every 2 or 3 months thereafter.

For this procedure you will need a voltmeter (a hand held autoranging DMM digital multimeter is the easiest), a 3/32" allen key, and a small 1/8" flat screwdriver.

1.Using the 3/32" allen key, remove the two silver hex cap head screws which secure the black oval insert to the faceplate. On page 8, which shows the FRONT panel of the amplifier, you can see 10 red tip jacks plus the black ground point that are hiding underneath the oval insert.

2.To measure the current draw of each output tube place the POSITIVE meter probe into the first red tip jack. (If you read a negative reading reverse the meter probes, no harm will be done.) Set the meter to read 'millivolts' DC (direct current) Voltage. You'll be reading less than one volt.

3.Each of the ten output tubes can have its own bias adjusted by adjusting its own bias adjust potentiometer. Above the measurement tip jacks you can see each tube's blue bias adjust pot.

4.The first step to setting the bias is to turn on the amplifier in triode mode and ensure that there is zero signal input by engaging the Input MUTE switch. Also, you MUST leave your loudspeakers connected as these provide an ideal load on the output. DO NOT EVER OPERATE YOUR AMPLIFIER WITHOUT SPEAKERS CONNECTED! Leave the amplifier on long enough to ensure that the tubes have reached their stable current draw, at least 1/2 hour is recommended.

5.Place the meter probes in the first red tip jack to read output tube #1. Adjust the first bias trim pot slowly until you measure 275-285 mVDC (0.275V to 0.285VDC). Since you are measuring across a 10 ohm cathode resistor, this would correspond to a 27 to 28 mA current draw for each tube by Ohm's law. A reading of 0mV can indicate a failed tube, or an open cathode resistor. A reading of 0mV on ALL tubes (powered on condition) can mean the B+ fuse has blown. The cause of this should be investigated before simply putting a new fuse in. You probably lost a tube and it blew the fuse. Have a look at the tubes to see if something looks weird.

6.If an individual tube cannot be adjusted to at least 250mV, or it cannot be adjusted below 300mV, then you should replace that tube (also see "Troubleshooting").

7.Follow step five with the remaining tubes, switching to the next tube point and adjusting the next trim pot each time. After you have adjusted all the output tubes, recheck and repeat the procedure as they will drift a little bit during adjustment. Once they are all set, your amplifier should be in perfect operation. (BIAS IN TETRODE MODE SHOULD READ 270mV TO 310mV. THERE IS A MASTER BIAS ADJUSTMENT TRIMPOT INSIDE THE UNIT, THIS TRIMPOT IS FACTORY SET ).

AMPLIFIERS specifications

Manley Labs, a renowned name in high-fidelity audio equipment, has established a reputation for its premium amplifiers, celebrated for their exceptional sound quality and innovative design. With a commitment to craftsmanship and the integration of cutting-edge technology, Manley amplifiers cater to audiophiles and professionals alike, delivering a listening experience that is both immersive and authentic.

One of the hallmark features of Manley amplifiers is their use of high-quality vacuum tubes in many of their models. The warmth and richness that tubes impart to the audio signal are particularly appealing to music lovers who seek a classic analog sound. Models like the Manley Stingray and the Manley 300B offer a distinctive tonal character, allowing musicians and listeners to experience the nuances of recordings as intended by the artists.

In addition to tube technology, Manley amplifiers frequently incorporate advanced solid-state circuitry, striking a balance between traditional warmth and modern reliability. The Manley Reference Amplifier exemplifies this hybrid approach, featuring a robust power supply and precision engineering that ensures a clean, dynamic sound. This versatility allows the amplifiers to perform beautifully in various listening environments, from home setups to professional studio applications.

Manley Labs is also notable for its attention to build quality. The amplifiers are crafted in the USA, utilizing high-grade components and rigorous quality control processes. This commitment to craftsmanship means that every unit is built to last, ensuring long-term reliability and performance. The aesthetic appeal of Manley amplifiers, with their distinctive vintage-inspired designs and premium finishes, further enhances their desirability.

Another key characteristic of Manley amplifiers is their versatility in handling various types of audio signals. Models like the Manley Neo-Classic 300B can accommodate both low-impedance and high-efficiency speakers, making them suitable for a wide range of setups. Additionally, features such as customized input and output transformers help to optimize the performance for different audio sources.

In conclusion, Manley Labs amplifiers embody a blend of vintage charm and contemporary engineering. Their proprietary tube designs, robust solid-state options, and unwavering quality make them a standout choice for anyone seeking an exceptional audio experience. Whether in a casual listening room or a high-end studio, Manley amplifiers promise to deliver richness, clarity, and a connection to the music that transcends the ordinary.