Bosch Appliances DS924IPET specifications Overview, Specifications General, Mounting Procedure

DS924iPET (ITI # 60-511-02-95)

Learn Mode (LM) Wireless PIR Motion Sensor

Installation Instructions

1.0 Overview

The DS924iPET is a Passive Infrared (PIR) Motion Sensor designed to detect movement in the interior of a structure by sensing the Infrared energy emitted from the human body as it moves across the Sensor’s field of view. When motion is detected the unit sends an alarm signal to the Control Panel. The DS924iPET is a high performance PIR Motion Sensor which uses advanced signal processing to provide outstanding catch performance and unsurpassed false alarm immunity. The DS924iPET is designed to ignore a dog up to 40 pounds, two cats and small rodents.

2.0Specifications General

• Power is supplied by 3.6 VDC Lithium Battery. Saft LS14250 (0.85 AH, 1/2AA battery).

• Typical current draw is 12 micro-amps with LED disabled.

AVOID

Hot or cold air	Direct or
directed onto
	reflected
sensor
	sunlight

Figure 1

4.0Mounting Procedure

4.1Surface or Corner Mounting

For Pet Applications, surface or corner mount the detector. Do not use the optional swivel bracket.

• Typical battery life is 5 years.

• Operating temperature range of +32°F to +120°F (0°C to +49°C).

PIR Motion Sensor

• Coverage area 35 ft. by 35 ft.

• Internal coverage pointability +2° to -10° Vertical and ±10° Horizontal.

• Field selectable sensitivity options of Standard, Intermediate, or High.

IMPORTANT

6.5 Ft (2 M)

Don't point at stairs

NO

Don't point where pets can climb

NO

• Three minute transmitter lockout time after alarm extends battery life.

• Timed Walk Test Mode automatically disables LED after setup to extend battery life.

Mount the detector 6 1/2 feet (2 meters) above the floor

Figure 2

• Cover activated Tamper indication. Optional wall activated Tamper is included.

RF Transmitter

• Integral RF transmitter capable of transmitting at least 500 feet open air. (Actual acceptable transmitter range should be verified for each installation).

• Transmits low battery report (trouble) to the Control Panel.

• Transmits supervisory signal to the Control Panel every 64 minutes.

• Intended for use with listed compatible ITI Learn Mode control panels.

3.0 Installation Guidelines

Do

• Keep all sensors within 100 feet of the Control Panel. The 100 foot distance recommendation is given as a starting guideline. The LM PIR Transmitter has an open air range of at least 500 feet, but the installation environment may influence this range.

• Mount the sensor so there is a reference point (such as a wall) at the end of its detection pattern.

• Mount the sensor so that an intruder will most likely walk across the detection pattern.

• Mount the sensor 6.5 feet above the floor.

• Mount on an insulated outside wall facing in.

• Mount on a surface which is rigid and free from vibration.

Don’t

•Mount in direct sunlight.

•Aim at air conditioners, heat vents, wood stoves, fireplaces, intermittent heat sources, etc.

•Aim at solar heated walls or uninsulated metal walls.

•Aim at normally moving objects (ceiling fans, pets over 40 pounds, etc.).

•Mount the sensor where it can be exposed to moisture.

•Mount in locations where the temperature may be outside the sensor’s operating limits of +32°F to +120°F (0°C to +49°C).

•Mount in areas with large metallic surfaces (e.g. heating ducts) or electrical wiring which may inhibit the sensor’s RF signals from reaching the Control Panel.

•Mount in areas where the coverage may be blocked by any temporary items such as boxes or freight.

• Remove the sensor’s cover by gently inserting a screwdriver into the

notch at the bottom of the cover.					COVER
					HINGES
• Completely loosen the mounting
base locking screw.					10	5 0 5 10
• Remove the mounting plate from
the enclosure by prying it up
and out from the bottom.						LENS			LENS
• Punch out 2 appropriate holes									FRAME
					WALK TEST LED
in the mounting plate (for
surface or corner applications).				0				S
				4				I	SENSITIVITY PINS
			WALK TEST	8				H
Note: The wall tamper cannot				TEST
			SWITCH						VERTICAL ADJUST
			WALL TAMPER
be used when corner									SCREW
			BYPASS	TAMPER
			JUMPER				MOUNTING BASE
mounting.				SWITCH	COVER
								LOCKING
					LATCH			SCREW
• If the wall tamper function is				FRONT VIEW OF ENCLOSURE WITH COVER OFF
					Figure 3
required,	remove	the
rectangular knockout. Locate the small spring in the hardware kit. Hold
the PIR base so the battery is visible. Place the spring on the black plastic
shaft of the wall tamper switch just below the battery.
• Remove the wall tamper bypass jumper located next to the walk test
switch.
• Using the mounting plate as a template, mark the location of the required
holes on the mounting surface.
• For installation on drywall or plaster, drill a 1/8" pilot hole to determine if a
wall anchor is required.
• Secure the mounting plate to the wall with the #6 x 1" wood screws
provided.
	HINGE
	CORNER
SURFACE
		SURFACE
CORNER		CORNER
			FLUSH					CORNER
KNOCKOUT			MOUNT					MOUNT
FOR	TAB
WALL TAMPER

MOUNTING Figure 4