Lincoln Electric LA-9, LA-26V, LA-17V manual Safety

Page 2

i

SAFETY

i

WARNING

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel engine exhaust and some of its constituents are known to the State of California to cause can- cer, birth defects, and other reproductive harm.

The Above For Diesel Engines

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

The Above For Gasoline Engines

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box 351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

FOR ENGINE powered equipment.

1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running.

____________________________________________________

1.b.Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.

____________________________________________________

1.c. Do not add the fuel near an open flame welding arc or when the engine is running.

Stop the engine and allow it to cool before refueling to prevent spilled fuel from vaporiz- ing on contact with hot engine parts and igniting. Do not spill fuel when filling tank. If fuel is spilled, wipe it up and do not start engine until fumes have been eliminated.

____________________________________________________

1.d. Keep all equipment safety guards, covers and devices in position and in good repair.Keep hands, hair, clothing and tools away from V-belts, gears, fans and all other

moving parts when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safety guards to perform required maintenance. Remove guards only when necessary and replace them when the maintenance requiring their removal is complete. Always use the greatest care when working near moving parts.

___________________________________________________

1.f. Do not put your hands near the engine fan. Do not attempt to override the governor or idler by pushing on the throttle control rods while the engine is running.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while turning the engine or welding generator during maintenance work, disconnect the spark plug wires, distributor cap or magneto wire as appropriate.

1.h. To avoid scalding, do not remove the radiator pressure cap when the engine is hot.

ELECTRIC AND MAGNETIC FIELDS may be dangerous

2.a. Electric current flowing through any conductor causes localized Electric and Magnetic Fields (EMF). Welding current creates EMF fields around welding cables and welding machines

2.b. EMF fields may interfere with some pacemakers, and welders having a pacemaker should consult their physician before welding.

2.c. Exposure to EMF fields in welding may have other health effects which are now not known.

2.d. All welders should use the following procedures in order to minimize exposure to EMF fields from the welding circuit:

2.d.1. Route the electrode and work cables together - Secure them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and work cables. If the electrode cable is on your right side, the work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as possible to the area being welded.

2.d.5. Do not work next to welding power source.

Mar ‘95

LINCOLN

ELECTRIC

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Operating Manual Safety Electric Shock can kill Cylinder may explode if damaged Précautions DE Sûreté LA-9 Models AIR-COOLED AmpsTypical Current Ranges for Tungsten Electrodes LA-17, LA-17V Models AIR-COOLED 150 Amps Tungsten Gas Lens Electrode Collet Collet Body Diameter LA-26, LA-26V Models AIR-COOLED 200 Amps Typical Current Ranges for Tungsten Electrodes Connection Diagrams KP505 For LA-9, LA-17, LA-26 Atenção PrecaucionWarnung Warnung

LA-26V, LA-9, LA-26, LA-17, LA-17V specifications

Lincoln Electric is renowned for its innovative welding equipment, and among their extensive range of products are the welding and cutting helmets known as LA-26, LA-17, LA-9, LA-26V, and LA-17V. Each of these models is designed to meet the diverse needs of professional welders and hobbyists alike, providing excellent protection while enhancing the overall welding experience.

The LA-26 helmet features a high-performance auto-darkening filter that adjusts its shade according to the welding process. This model is characterized by a lightweight design for comfort during extended use, and it provides excellent coverage and visibility, making it particularly suitable for MIG, TIG, and Stick welding applications. Its adjustable sensitivity and delay settings allow users to customize their welding experience based on personal preference.

The LA-17 helmet is another top-tier option from Lincoln Electric. Designed with a broader viewing area, it ensures welders have a clear line of sight while maintaining safety standards. This model incorporates a fast-reacting auto-darkening filter that transitions quickly to a dark state, enhancing the user's ability to work on different welding tasks. Moreover, the LA-17 is designed with a robust and durable shell, making it ideal for tough working environments.

For those looking for a more portable option, the LA-9 model stands out with its compact design and user-friendly features. This helmet is particularly favored by hobbyists and DIY enthusiasts for its affordability and effectiveness. It offers a quick reaction time and a fixed shade, making it suitable for basic welding tasks.

The LA-26V and LA-17V models bring a significant technological advancement with their variable shade options. These helmets allow welders to adjust the darkness of the lens depending on the task at hand. The LA-26V provides a versatile range, catering to various welding processes and ensuring optimal vision and protection across different conditions. Likewise, the LA-17V offers enhanced eyeball protection and UV/IR filtering for professional-grade welding.

Each of these Lincoln Electric helmets embodies the brand’s commitment to safety, comfort, and performance, making them staples in both professional and recreational welding applications. With features that prioritize user satisfaction and high standards in weld quality, these helmets are essential tools for any welding task.
Top Page Image Contents