SECO-LARM USA SK-1123-FQ warranty Introduction, Dimensions Parts List, Delete User

ENFORCER FLUSH-MOUNT OUTDOOR ACCESS KEYPAD
TABLE OF CONTENTS
Introduction	2
Dimensions	2
Unique Features	3
Wiring – Basic Diagram	4
Specifications	5
Output 2 (NPN Transistor Open Collector)	6,7
Wiring – Example, with Connection to Lock Device and Alarm Arm/Disarm	7
User Code Worksheet	8,9
Wiring – 2 Keypads with Mantrap Interlock	10
Wiring – Auxiliary Accessories	11
Programming Notes	12
LED Indicators	12
Preparing to Program	13
Getting Started	13
User Programming	13
Installer Programming	14
Reprogram the Keypad (Select Data)	15
Reprogram the Keypad (Complete Data Refresh)	15
Delete User	15
Master Code Bypass (DAP jumper)	15
Quick Reference Guide	16

INTRODUCTION

The SK-1123-FQ is the ideal keypad for office, commercial, and home security installations. This self-contained security keypad has a built-in 5-Amp relay output and a 100mA transistor ground output for maximum flexibility when connecting to electronic door strikes, door alarms, door chimes, alarm control panels, or other security and access control applications. The outputs can be programmed for timed (1~999 seconds) or ON/OFF operation.

The SK-1123-FQ can be programmed for up to 100 4-digit to 8-digit user codes for the primary output, and up to 10 4-digit to 8-digit user codes for the secondary output. All programming and code information is stored in non-volatile EEPROM memory to protect the data in case of power loss.

DIMENSIONS						PARTS LIST
		5/8‖ (15mm)
			123/32‖
			(31mm)			Keypad x 1
						Diode x 1
						Security screw x 2
						Security wrench x 1
	43/4‖
				25/8	‖
	(120mm)
				(66.5mm)

31/8‖ (80mm) 115/16‖

(46mm)

ENFORCER FLUSH-MOUNT OUTDOOR ACCESS KEYPAD

REPROGRAM THE KEYPAD (SELECT DATA)

To change certain data in the keypad (such as to delete or change user codes), do the following:

1. Enter programming mode by keying in the master code and the key:

x x x x The keypad is now in the programming mode.

2.Use the programming instructions on page 13 and 14 to make desired changes to the keypad’s data.

3.Exit the programming mode by pressing the key.

REPROGRAM THE KEYPAD (COMPLETE DATA REFRESH)

Sometimes it may be necessary to completely erase all current data (except the master code) and input new data. An example of when this may be necessary is the sale of a protected building to a new owner. In such a situation, do the following:

1.Enter the programming mode by keying in the master code and the key, then enter the refresh code, 8 9 0 1 and the # key:

x	x	x	x		The keypad is now in the programming mode.
					All old data is cleared and the keypad is ready for new data.
8	9	0	1	#

Note: The master code does NOT change.

2.Use the programming instructions on pages 13 and 14 to enter the keypad’s data.

3.Exit the programming mode by pressing the key.

DELETE USER

To delete a user who no longer has authority to enter the protected area:

1. Enter program mode by keying in the master code and the						key:
	x	x	x	x	The keypad is now in the programming mode.

2. Enter the output #, user ID number, and the # key.

To delete user ID 05 from output #1, press	1	0	5	#
To delete user ID 1 from output #2, press	2		1	#
3. Exit the programming mode by pressing the		key.

MASTER CODE BYPASS (DAP JUMPER)

If the master code has been forgotten or does not work, use the DAP (direct access to program) jumper to override the forgotten code and permit direct entry into the programming mode as follows:

1.Disconnect the power supply.

2.Move the DAP jumper from OFF to ON.

3.Reconnect the power supply. The keypad will start beeping.

4.Move the DAP jumper back to the OFF position. The keypad will stop beeping as soon as the jumper is removed.

5.Key in a new master code as follows:

Option*		Key in New Code					Confirm		Exit
	0		x	x	x	x		#

*Zero ―0‖ is for new master code only; see page 13 and 14 for other options.

Note: DAP reset does not change any previously configured settings. DAP will only give direct access to programming by bypassing the master code requirement.

Page 2 SECO-LARM® U.S.A., Inc. SECO-LARM® U.S.A., Inc. Page 15