First Alert FA168CP-CN Field Function, Programmable Values, System Setup, Zone Sounds and Timing

352*5$00,1*￿)250

Entry of a number other than one specified will give unpredictable results. Values shown in brackets are factory defaults.

Entries shown in dashed boxes indicate partition entries for FA168C only (not applicable for FA148CP).

Field	Function		Data Entries				Programmable Values
SYSTEM SETUP (		✱20–	✱29)
✱ 20	INSTALLER CODE						4 digits, 0–9
						[4112]
✱21	QUICK ARM ENABLE				[0,0]		0 = no; 1 = yes
			Part. 1	Part.2

✱22	RF JAM OPTION		[0]
✱23	FORCED BYPASS		[0,0]
		Part. 1 Part. 2

0 = no RF Jam detection; 1 = send RF Jam report

UL: must be 1 if wireless devices are used

0 = none UL: must be “0”

1 = bypass open zones

✱ 24	RF HOUSE ID CODE
		Part. 1	Part. 2	Common
✱26	CHIME BY ZONE		[0]
✱27	X–10 HOUSE CODE		[0]

00 = disable all wireless keypad usage

01–31 = using 5827, 5827BD or 5804BD keypad [00,00,00]

0	= no; 1	= yes (select zones to chime on zone list 3,
using *81 Menu mode)
0	= A; 1	= B, 2 = C, 3 = D, 4 = E, 5 = F, 6 = G,
7	= H, 8	= I, 9 = J, #10 = K, #11 = L, #12 = M, #13 = N,
	#14 = O, #15 = P UL: not for fire or UL installations

✱28	ACCESS CODE FOR
				[00]
	4285/4286 PHONE MODULE
		(Partition 1 only)
✱ 29	LONG RANGE RADIO OUTPUT		[0]
ZONE SOUNDS AND TIMING (		✱31 – ✱39)

00 = disable; 1st digit: enter 1–9; 2nd digit: enter # + 11 for "✱", or # + 12 for "#".

UL: must be “00” for UL Commercial Burg. installations

0 = disable; 1 = enable

✱31 ONE AUDIBLE ALARM PER ZONE

✱32 FIRE ALARMSOUNDER TIMEOUT

✱33 ALARM SOUNDER TIMEOUT

✱34 EXIT DELAY

[0]

[0]

[1]

[70,70]

0 = no UL: must be “0” ; 1 = yes

0 = sounder stops at timeout;

1 = no sounder timeout UL: must be “1” for fire install.

0 = none; 1 = 4 min; 2 = 8 min; 3 =12 min; 4 = 16 min; UL: minimum “1” (4 min.)

00–99 = seconds of exit delay time for each partition Common zones use same delay as partition 1.

Part. 1 Part. 2

✱35 ENTRY DELAY #1 (zone type 01)

✱36 ENTRY DELAY #2 (zone type 02)

✱37 AUDIBLE EXIT WARNING

✱38 CONFIRMATION OF ARMING DING

[30,30]

Part. 1 Part. 2

[60,60]

Part. 1 Part. 2

[1,1]

Part. 1 Part. 2

[0,0]

Part. 1 Part. 2

00–99 = seconds of entry delay #1 time for each partition; UL: 45 seconds max.

Common zones use same delay as partition 1.

00–99 = entry delay #2 time for each partition; UL: 60 seconds max.

Common zones use same delay as partition 1.

0 = no; 1 = yes

0 = no; 1 = yes (wired keypads and RF) 2 = yes, RF only

✱39	POWER UP IN PREVIOUS STATE			[1]
DIALER PROGRAMMING (		✱40 – ✱42)
Enter the number of digits shown. Do not fill unused spaces. Enter 0–9; #+11 for '
maximum digits entered, exit the field by pressing [			✶] and next desired field number.

0 = no; 1 = yes UL: must be “1”

✱'; #+12 for '#'; #+13 for a 2-second pause. If fewer than the

✱40 PABX ACCESS CODE

				Enter up to 6 digits. To clear entries from field, press			✱40 ✱ .
✱ 41	PRIMARY PHONE No.
		Enter up to 20	digits. To clear entries, press		✱41	✱ .
✱ 42	SECOND PHONE No.
		Enter up to 20	digits. To clear entries, press		✱42	✱ .

– 3 –