Kenmore I 53.329662 65 GALLON Anode Rod Inspection, Temperature-Pressure Relief Valve Operation

Page 18

NOTE:It is notnecessaryto adjusttheupperthermostat. However,ifit isadjustedabovethefactorysetpointof 120°F (49°C),it isrecommendedthatit notbesethigherthanthe lowerthermostatsetting.

Theupperandlowerthermostatsareadjustableifa different watertemperatureis desired.Readall warningsin the

"Temperature-Regulation"

section

before proceeding.

1.Turn "OFF" the electric power to the water heater at the junction box.

[

,, Before removing any access panels or servicing the water heater, make sure the electrical

supply to the water heater is turned "OFF".

,,Failure to do this could result in death, serious bodily injury, or property damage.

2.Take off the upper and/or lower access panel, insulation cap with handle.

3.The slotted adjustment (using a screwdriver) can be turned

clockwise ( f'_ ) to increase the temperature setting or counter clockwise ( _'_ ) to decrease the temperature setting.

4.Replace the insulation cap with handle and access panel.

5.Turn "ON" the power supply.

Anode Rod Inspection

Property Damage Hazard

• Avoid water heater damage.

. Inspection and replacement of anode as needed.

The anode rod is used to protect the tank from corrosion. Most

hot water tanks are equipped with an anode rod. The

submerged rod sacrifices itself to protect the tank. Instead of corroding the tank, water ions attack and eat away the anode rod. This does not affect the water's taste or color. The rod must be maintained to keep the tank in operating condition.

Anode deterioration depends on the water conductivity, not

necessarily water condition. A corroded or pitted anode rod

indicates high water conductivity and should be checked and/ or replaced more often than an anode rod that appears to be

intact. Replacement of a depleted anode rod can extend the

life of your water heater. Inspection should be conducted by calling Sears Service Center. At a minimum the anode(s) should be checked annually after the warranty period.

Temperature-Pressure Relief Valve Operation

The temperature-pressure relief valve must be manually operated at least once a year.

•Burn hazard

•Hotwater discharge.

•Keep clear of relief valve discharge outlet.

The temperature-pressure relief valve must be manually operated at least once a year. Caution should be taken to ensure that (1) no one is in front of or around the outlet of the

temperature-pressure relief valve discharge line, and (2) the water manually discharged will not cause any property damage or bodily injury. The water may be extremely hot.

TEMPERATURE_PRESSURE

DISCHARGE PiPE

FIGURE 28.

If after manually operating the valve, it fails to completely reset

and continues to release water, immediately close the cold water inlet to the water heater, follow the draining instructions,

and replace the temperature-pressure relief valve with a new

one.

Failure to install and maintain a new properly listed temperature-

pressure relief valve will release the manufacturer from any

claim which might result from excessive temperature or pressure.

If the temperature-pressure relief valve on the appliance weeps

or discharges periodically, this may be due to thermal

expansion. Your water heater may have a check valve installed in the water line or a water meter with a check valve. Consult

your local Sears Service Center for further information. Do not

plug the temperature-pressure relief valve.

Draining

. Burn hazard

•Hot water discharge.

•Keep hands clear of drain valve discharge.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Troubleshooting Parts List OperationSears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A Important Definitions Explosion Hazard Fire Hazard / Electric Shock HazardRepair Parts List Minimum TankMaximum Fuse GALS,PER HourTools Needed When Sweat Basic ToolsSoldering Removing the Old Water Heater Facts to Consider About Convertible Lower Element Facts to Consider About the LocationInsulation Blankets Property Damage HazardWater Piping Wate R H EaterElectric Listed Temperature-Pressure Relief Valve Valve and Pipe InsulationFilling the Water Heater Water Damage HazardAIR GAP Converting the Lower Element Convertible Lower Element sectionTerminal Cover from Fire and Explosion HazardFire and E×plosion Hazard ThermostatWiring WiringDiagramsseeWiring Diagrams section have been GreenWiring Diagrams Upper and Lower Thermostat Adjustments Temperature RegulationTemperature Settings Adjustable Upper ThermostatAnode Rod Inspection Temperature-Pressure Relief Valve OperationTemperaturepressure DrainingThermostat Removal/Replacement Element Cleaning/ReplacementUpper and Lower Thermostat with High Limit Upper and Lower Thermostat with High Limit Fire Hazard Electric Shock Hazard Lift OUT TAB to Unclip Terminal Cover From ThermostatDrain Valve Washer Replacement ServiceWasher Start Up Conditions ChartOperational Conditions ExpansionCorrosionprotectiveactionoftheanode Flammable hydrogen gases may be presentShut off system. See High Temperature Shut Off System Make sure the electrical supply to your water heater is onTheelementmaybeleakingatthetankfitting MakesuretheelectricsupplyhasbeenturnedOFF,andnever153.329264I 38GallonShortI Key153.329463 153.329363153.329462 153.329562Kenmore Power Mber TM Electric Water Heaters 3 4 5 6Page Page Year Limited Warranty on Water Heater Masterprotectionagreements
Top Page Image Contents