Kenmore 153.336333 Draft Hood Installation, Vent Pipe System, Vent Pipe Size, Vent Connectors

Page 19

 

1 SQ. INCH PER

 

2000 BTUH

CONFINED

OUTLET

 

SPACE

 

 

OUTDOOR

 

AIR DUCTS

using the manufacturer’s instructions and local codes, rules, or regulations.

IMPORTANT: If you lack the necessary skills required to properly install this venting system, you should not proceed, but get help from a qualified technician.

Draft Hood Installation

SHEET METAL SCREWS (FOUR PROVIDED)

INLET

LEGS

DRAFT HOOD

1 SQ. INCH PER

2000 BTUH

ALL AIR FROM OUTDOORS USING HORIZONTAL DUCTS

FIGURE 16.

 

ALTERNATIVE

 

OPENING

 

LOCATION

CONFINED

1 SQ. INCH

PER 3000 BTUH

SPACE

 

ALL AIR FROM OUTDOORS - USING A SINGLE PERMANENT OPENING

FIGURE 17.

Vent Pipe System

This water heater uses a non-direct, single-pipe vent system to remove exhaust gases created by the burning of fossil fuels. Air for combustion is taken from the immediate water heater location or is ducted in from the outside (see “Combustion Air Supply and Ventilation”).

This water heater must be properly vented for the removal of exhaust gases to the outside atmosphere. Correct installation of the vent pipe system is mandatory for the proper and efficient operation of this water heater and is an important factor in the life of the unit.

The vent pipe must be installed according to all local and state codes or, in the absence of local and state codes, the “National Fuel Gas Code”, ANSI Z223.1(NFPA 54)-current edition. The vent pipe installation must not be obstructed so as to prevent the removal of exhaust gases to the outside atmosphere.

IMPORTANT: The use of vent dampers is not recommended by the manufacturer of this water heater. Although some vent dampers are certified by CSA International, this certification applies to the vent damper device only and does not mean they are certified for use on this water heater.

U.L. recognized fuel gas and carbon monoxide (CO) detectors are recommended in all applications and should be installed

LEGS

SLOT

SLOT

 

JACKET TOP

INSTALL THE DRAFT HOOD WITH

THE FOUR SCREWS PROVIDED.

FIGURE 18.

Align the legs of the draft hood with the slots provided. Insert the legs and secure the draft hood to the water heater’s top with the four screws provided as shown in Figure 18. Do not alter the draft hood in any way. If you are replacing an existing water heater, be sure to use the draft hood supplied with this water heater.

Vent Pipe Size

It is important that you follow the guidelines in these instructions for sizing a vent pipe system. If a transition to a larger vent size is required, the vent transition connection must be made at the draft hood outlet.

Vent Connectors

1.Type B, Double wall, U.L. Listed Vent Pipe.

2.Single wall Vent Pipe.

Maintain the manufacturer’s specified minimum clearance from combustible materials when using type B double wall vent pipe.

Vent connectors made of type B, double wall vent pipe material may pass through walls or partitions constructed of combustible material if the minimum listed clearance is maintained.

Maintain a six inch minimum clearance from all combustible materials when using single wall vent pipe.

IMPORTANT: Single wall vent pipe cannot be used for water heaters located in attics and may not pass through attic spaces, crawl spaces or any confined or inaccessible location. A single wall metal vent connector cannot pass through any interior wall.

When installing a vent connector, please note the following (See Figures 19-21):

•Install the vent connector avoiding unnecessary bends, which create resistance to the flow of vent gases.

•Install without dips or sags with an upward slope of at least 1/4-inch per foot.

•Joints must be fastened by sheet metal screws or other approved means. It must be supported to maintain clearances and prevent separation of joints and damage.

•The length of the vent connector cannot exceed 75% of the vertical vent height.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A Power Miser GAS Water HeaterSafety Precautions Safe INSTALLATION, USE and ServiceFire or Explosion Hazard Table of Contents Troubleshooting Guide Year Limited Warranty on Water Heater Product WarrantyImportant Information About This Water Heater Customer ResponsibilitiesJacket TOP Product SpecificationsMaterials Needed Materials and Basic Tools NeededVent Pipe Inner Door Typical InstallationImportant Information about this Water Heater Installation ChecklistRemoving the Old Water Heater Installation InstructionsSite Location Location RequirementsInsulation Blankets Clearances and AccessibilityGas Piping Filling the Water HeaterGAS Supply Gas RequirementsGas Pressure Gas Pressure TestingLP Gas Only Unconfined Space Combustion AIR Supply & VentilationAll Air from Inside the Building Louvers and Grilles All Air from OutdoorsVent Pipe Size Draft Hood InstallationVent Connectors Vent Pipe SystemVertical Exhaust Gas Vent Chimney ConnectionWater System Piping Piping InstallationClosed System/Thermal Expansion Temperature and Pressure Relief ValveLighting Instructions Operating Your Water HeaterEmergency Shut Down Water Temperature RegulationChecking the Draft Burner Flames110 Vent System Inspection Burner Inspection Service and AdjustmentTank Sediment Cleaning Burner CleaningDraining and Flushing Temperature-Pressure Relief Valve OperationHousekeeping Anode Rod InspectionService Maintenance of Your Water Heater Cleaning the Combustion Chamber and Flame-arrestor Replacing the Pilot/ Pilot Tube AssemblyPiezoelectric Igniter System Replacing the Manifold/Burner AssemblyRemoving the Gas Valve Testing the Igniter SystemFvir System Operational Checklist Removing and Replacing the Gas Control Valve/ThermostatStart Up Conditions Troubleshooting GuideCondensation Operational ConditionsLeakage Checkpoints Problem Possible Causes Corrective Action Troubleshooting ChartThermostat Fails to YES Pilot Light Troubleshooting FlowchartPage Model Numbers Key No. Part Description Parts Order ListPower Miser 6 GAS Water Heater Page Page MY-HOME1-800-469-4663 Get it fixed, at your home or ours

153.336482, 153.336372, 153.336333, 153.336433, 153.336472 specifications

The Kenmore series 153.336433, 153.336382, 153.336472, 153.336333, and 153.336482 represents a collection of top-tier appliances engineered to enhance home convenience and efficiency. Each model in this lineup boasts unique features, technologies, and characteristics, catering to diverse consumer needs.

First, the aesthetic appeal of the Kenmore appliances is paramount. Available in various finishes, including sleek stainless steel and classic white, they blend seamlessly into any kitchen decor, adding a touch of sophistication. The ergonomic design allows for easy operation and maintenance, ensuring that each appliance serves not just as a tool, but as a design statement.

One of the standout features across the models is their energy efficiency. Equipped with advanced energy-saving technologies, these appliances significantly reduce electricity and water consumption without compromising performance. The Energy Star certification on many models means consumers can enjoy substantial savings on utility bills while contributing to environmental sustainability.

Another key characteristic is the innovation in cooking technology. Many models incorporate smart technology that enables remote control and monitoring via smartphone applications. Users can preheat ovens, adjust settings, and track cooking times from anywhere in the home, ensuring perfectly cooked meals with minimal hassle.

The series also includes versatile cooking settings that cater to various culinary styles. Features such as convection cooking, steam assist, and multi-cooking modes enable users to experiment with a wide range of recipes. The user-friendly interface makes it simple to select the desired cooking method, ensuring that even novice cooks can prepare gourmet dishes effortlessly.

Safety features are a priority in the Kenmore range, with options like automatic shut-off, child safety locks, and temperature controls designed to prevent accidents in the kitchen. These appliances are built with durability in mind, utilizing high-quality materials that promise longevity and reliability.

In summary, the Kenmore models 153.336433, 153.336382, 153.336472, 153.336333, and 153.336482 combine style, efficiency, and innovation to elevate everyday cooking experiences. With their standout features and commitment to quality, these appliances are set to remain a popular choice for homeowners seeking to enhance their culinary endeavors. Whether you're renovating your kitchen or simply upgrading existing appliances, the Kenmore series offers unmatched performance and reliability.
Top Page Image Contents