Breckwell Breckwell Hearth Products LUXURY SERIES, P2700 owner manual Electrical Installation

Page 9

INSTALLATION

9

E.INSTALLATION THROUGH SIDE OF MASONRY CHIMNEY NOTE: Follow L-Vent chimney manufacturer’s instructions.

1.Position the stove, adhering to the clearances in Figures 1 & 2. Mark the center of the hole where the pipe is to pierce the masonry chimney.

2.It will be necessary to break out the masonry around the location of the pipe center mark. Use a 4-inch diameter hole for 3-inch pipe and 5-inch diameter hole for 4-inch pipe.

3.Measure and build chimney top plate. Cut out holes for chimney pipe, and if used the outside air pipe.

4.Install the tee on the bottom of the vertical pipe system and lower it down the chimney until the center branch of the tee is level with the center of the hole in the masonry, as shown in Figure 10.

5.Install and seal the top plate from step 3 with non-hardening mastic. Slip the storm collar over the pipe, and while holding the pipe at the proper elevation, affix the collar with a minimum of three ¼” stainless steel sheet metal screws. Seal all joints and seams around the collar.

6.Connect the horizontal pipe by pushing it through the hole in the masonry and lining it up with the branch in the tee. Push the pipe into the tee while twisting it to lock it into the tee.

7.If desired, once the horizontal pipe is in place, the space between the pipe and masonry may be filled with high-temperature grout.

8.Install the trim collar. An adjustable pipe length and adapter may be needed to finish the connection to the stove.

ELECTRICAL INSTALLATION

This stove is provided with a 6-foot grounded electrical cord extending from the rear of the stove. We recommend connecting to a good quality surge protector that is plugged into a standard three-prong, 120V, 60 Hz electrical outlet. Voltage variations can lead to serious performance problems. The Breckwell electrical system is designed for 120V AC with no more than 5% variation. Breckwell cannot accept responsibility for poor performance or damage due to inadequate voltage. If connected to an older, two-prong outlet, a separate ground wire should be run to a proper ground (refer this to a qualified technician). Always route the electrical cord so that it will not come in contact with any hot part of the stove.

SPECIAL MOBIL HOME REQUIREMENTS

WARNING: DO NOT INSTALL IN A SLEEPING ROOM.

For installation in a mobile home, an outside source of combustion air must be used

(See “COMBUSTION AIR SUPPLY”).

The P2700 must be grounded to the steel chassis of the home with 8 Ga. copper wire using a serrated or star washer to penetrate paint or protective coating to ensure grounding.

The P2700 must be securely fastened to the floor of the mobile home.

Refer to “VENTING” for proper exhaust configurations.

CAUTION: THE STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED.

FIGURE 9

FIGURE 10

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Luxury Series P2700 Fuel IntroductionSafety Precautions Table of Contents Specifications InstallationPreparation ClearancesWhen Outside AIR is not Used INSTALLATION9Combustion AIR Supply VentingP2700 Installation Equivalent Vent Length EVLHorizontally Through Wall refer to Figure Vertically Into Existing Chimney System Vertically with NEW Chimney System Refer to FigureElectrical Installation Special Mobil Home RequirementsSee Combustion AIR Supply Operation PRE-START-UP Check Proper FuelBuilding a Fire Hotrod Automatic FirestarterShutdown Procedure Breckwell Maintenance ToolSafety Features RE-STARTING a Warm StoveThermostat Installation Thermostat InstallationOptional Thermostat ∙ a Millivolt Thermostat is RequiredPlease Read this ASH Removal MaintenanceASH Disposal Vacuum USEBlowers CleaningRecommended Maintenance Schedule Chimney CleaningRemoval and Replacement of Broken Door Glass Daily Weekly Annually or per TonTroubleshooting Guide Stove Shuts OFF and the # 2 Light FlashesPossible Causes Stove Shuts OFF and the # 3 Light Flashes Possible Causes Possible Remedies Stove Feeds PELLETS, but will not IgniteSmoke Smell Coming Back Into the Home Convection Blower Shuts OFF and Comes Back onFuel feed light is on, you have a bad control board Troubleshooting Guide Heat Level Setting P2700 High Limit Switch Keeps TrippingSmoke Smell or Soot BUILD-UP Digital Circuit Board Timing RatesElectrical Diagram LOG Replacement PartsLifetime Limited Warranty
Related manuals
Manual 4 pages 6.56 Kb

Breckwell Hearth Products LUXURY SERIES, P2700 specifications

The Breckwell P2700 is a top-tier pellet stove from the esteemed Breckwell Hearth Products Luxury Series. This model is designed to offer not only efficient heating solutions but also to enhance your living space with its elegant design. The P2700 is ideal for homeowners seeking both functionality and aesthetic appeal in their heating equipment.

One of the standout features of the Breckwell P2700 is its high heat output capability, which allows it to efficiently heat larger areas. With a maximum output of up to 50,000 BTUs, this stove can easily warm rooms and open-concept spaces, making it perfect for residential environments. This robust performance is paired with adjustable heat settings, providing users with the ability to control the temperature according to their comfort levels.

The P2700 brings the latest technology to the forefront with its advanced electronic control system. This system features a programmable thermostat that allows homeowners to set specific heating schedules tailored to their lifestyles. Additionally, this model is equipped with a digital display that provides real-time information on the stove’s operation, including temperature settings and pellet feed rates.

Breckwell has also prioritized user convenience with the P2700. The integrated hopper can hold up to 60 pounds of pellets, which means less frequent refueling and uninterrupted heating sessions. The hopper is designed for easy access, and the unit features a convenient cleaning system to streamline maintenance. With a simple pull of a lever, users can remove ash and debris, ensuring that the stove operates at peak efficiency.

Another noteworthy characteristic of the Breckwell P2700 is its environmentally friendly design. Pellet stoves are known for producing low emissions compared to traditional wood-burning stoves, and the P2700 is no exception. It meets stringent EPA standards, making it a responsible choice for eco-conscious consumers.

The aesthetic appeal of the P2700 cannot be overlooked. With its sleek, modern design and choice of finishes, it seamlessly integrates into any décor. The large viewing window offers a captivating view of the flames, creating a warm, inviting ambiance in any room.

In summary, the Breckwell P2700, part of the Luxury Series, stands out as a powerful, efficient, and stylish heating option. With its high BTU output, advanced technology, user-friendly features, eco-friendly performance, and elegant design, it represents an exceptional choice for anyone looking to enhance their home’s comfort and warmth.
Top Page Image Contents