Samson 5476 manual Technical data

Page 99

Appendix

12.4 Technical data

Inputs

7 configurable inputs for sensors (Pt 100 and PTC or

 

 

Pt 100 and Pt 1000 or Pt 100 and NTC) or binary alarms

 

Sensor inputs

 

1 outdoor temperature input for sensor or current signal 4 (0) to 20 mA

 

 

 

 

1 flow temperature sensor input

 

Binary inputs

BE1 optionally for releasing a control circuit or external demand

 

 

BE5 configurable for storage tank thermostat

 

Other inputs

Pulse or current input for capacity or flow rate limitation

 

 

Remote control to correct the room temperature and select the operating mode

 

 

Alternatively, potentiometer input 1 to 2 kΩ or configurable for binary alarm

Outputs

Three-step signals: Load 250 V AC, max. 2 A, min. 10 mA

 

Control signal outputs

On-off signals: Load 250 V AC, max. 2 A, min. 10 mA

 

 

Varistor suppression 300 V

 

Binary outputs

Max. 4 outputs to control pumps,

 

 

load 250 V AC, max. 2 A, min. 10 mA, varistor suppression 300 V

 

 

2 reed relay outputs for controlling the speed of a circulation pump or for

 

 

fault indication, load max. 24 V, 100 mA

 

 

 

Interfaces

Serial RS-485 interface for connection to four-wire bus, protocol: Modbus

 

 

RTU, data format 8N1or serial RS-232-C interface for connection to a

 

 

modem; connection over RJ-12 jack

 

 

Option: Meter bus interface

Operating voltage

230 V AC (+ 10 %/–15 %), 48 to 62 Hz

 

 

Power supply failure: All parameter settings and configuration data are

 

 

stored in an EEPROM in the case of power failure

Power consumption

Approx. 3 VA

Temperature range

Operation: 0 to 40 °C (avoid long periods of heat) Storage: –20 to 60 °C

Degree and class of

IP 40 according to IEC 529 and II according to VDE 0106

protection

 

Degree of contamination

2 according to VDE 0110

Overvoltage category

II according to VDE 0110

Humidity rating

F according to VDE 40040

Noise immunity

According to EN 61000-6-1

Noise emission

According to EN 61000-6-3

Weight

Approx. 0.6 kg

 

 

 

EB 5476 EN 99

Page 98 Page 100
Image 99
Page 98 Page 100
Contents Mounting and Operating Instructions EB 5476 EN Disclaimer of liability Contents Contents Contents Operation Operating elementsOperating keys Operating switches Operating modes Closed DisplayDisplaying data Setting the controller time Heating circuit Setting the times-of-useStart Entering public holidays Entering vacation periods Correcting temperature set points Activating and deactivating functions Start-up Setting the system code numberDisplay shows Current system code number Blink Enter key number Changing parametersCalibrating sensors Resetting to default values Manual operation DHW SystemsSystem Anl Default settings FB13 = OFF Without RF FB20 = on 26 EB 5476 EN FB15 = ON, select CF FB15 = ON, select Solar FB21 = OFF Solar collector 32 EB 5476 EN FB15 = ON, select CF 34 EB 5476 EN Default settings FB13 = OFF Without RF FB20 = on FB15 = on Systems 38 EB 5476 EN FB15 = on Weather-compensated control Functions of the heating circuitGradient characteristic · 4-point characteristic 2 4-point characteristicUnderfloor heating Fixed set point controlOT deactivation value in reduced operation Summer modeRemote operation Delayed outdoor temperature adaptationOptimization Adaptation Flash adaptationPotentiometer input Pump management· DHW heating in a storage tank system Functions of the DHW circuit · DHW heating in a storage tank charging system DHW heating in the storage tank charging system52 EB 5476 EN DHW heating in instantaneous heating system Anl DHW heating with solar system Anl 2, 3, 4, 5 undParallel pump operation Anl 2, 3 Circulation pump operation during storage tank chargingCirculation over the heat exchanger Intermediate heating operation Anl 2, 3Priority circuit Anl 4, 5, 6, 7, 8 Reverse controlSet-back operation Thermal disinfection of the DHW storage tank Forced charging of the DHW storage tank Anl 2, 3, 5, 7, 8Return flow temperature limitation Frost protectionForced operation of the pumps FB21 = on Three-step control Condensate accumulation controlOn/off control Releasing a control circuit over the binary inputProcessing of external demand in RK1 Flow rate/capacity limitation Limitation using pulse inputLocking manual levels Limitation using 0/4 to 20 mA signalSetting a customized key number Operational faults Collective error alarmSensor failure Error status register Temperature monitoringCommunication CommunicationController with RS-232-C port · Pin assignment of RS-232 port left and RS-485 port right Controller with serial RS-485 interfaceDescription of communication parameters to be adjusted Modem time-out t0 Meter bus interfaceFlow rate and/or capacity limitation via meter bus Activating the meter busInstallation Appendix Memory module InstallationPanel mounting Electrical connection TWF Systems Anl 1 to Systems Anl 5 to 80 EB 5476 EN Appendix Function block list Parallel pump Setting only possible after entering key number UP1 Circulation over BA8 12.2 Parameter list 88 EB 5476 EN Maximum flow temperature Can only be set after entering the key number Min. return flow temperature System Anl 9, underfloor heating circuit Min. flow temperature 20 to 130 C 20 C DHW heating DHW heating OFF 20 to 90 C 50 C 20 to 130 C 120 C ST.-NR Sensor resistance tables Technical data Customer data Model code WMZ 2 FB29 = on Parameter settings Appendix Public holidays and vacations SLP Key number 1732 Appendix Index PTC Thermal disinfection EB 5476 EN 0000 Page EB 5476 EN

5476 specifications

The Samson 5476 is a high-performance microphone designed for professional audio applications, offering exceptional quality and versatility for various recording environments. Known for its robust build and advanced features, the 5476 is a reliable choice for musicians, broadcasters, and sound engineers.

One of the standout characteristics of the Samson 5476 is its cardioid polar pattern, which effectively isolates the sound source while minimizing background noise. This feature is especially beneficial in live performance settings or during studio recordings where external noise can be a challenge. The microphone’s frequency response ranges from 20 Hz to 20 kHz, making it suitable for capturing a wide variety of sound sources, from deep bass notes to crisp high frequencies.

The 5476 incorporates a dynamic transducer that enhances its durability and reliability, ensuring it can withstand the rigors of frequent use. The built-in shock mount system further reduces handling noise and vibrations, allowing for clearer audio capture. Additionally, the microphone is equipped with a built-in pop filter, which mitigates plosive sounds that can occur during vocal recordings.

This microphone also features a low impedance output, ensuring compatibility with a wide range of mixing consoles and recording interfaces. Users can easily connect the 5476 to XLR inputs, making it straightforward to integrate into any professional audio setup. The microphone’s high output level ensures excellent signal integrity, providing clean and precise audio reproduction.

Another notable technology in the Samson 5476 is its advanced capsule design, which helps to enhance the microphone's sensitivity and transient response. This results in natural-sounding audio, whether it’s used for vocals, instruments, or ambient sounds. The microphone’s construction also includes a durable metal body that can withstand the wear and tear of live performances and frequent handling.

In summary, the Samson 5476 is a versatile and reliable microphone that combines advanced technology with practical features suited for both studio and live environments. Its cardioid pattern, dynamic transducer, low impedance output, and robust build make it a valuable tool for any audio professional looking to achieve high-quality recordings. Whether for vocals, instruments, or broadcasting, the Samson 5476 delivers consistent performance and exceptional sound quality, making it a top choice in its class.
Top Page Image Contents