Diagnostic Fault Code Storage and Retrieval

269434-UUM-A-0407

9 RED FLASHES: Indicates reversed line voltage polarity or grounding problem. Both heating and cooling operations will be affected. Check polarity at furnace and branch. Check furnace grounding. Check that flame probe is not shorted to chassis.

10 RED FLASHES: Gas valve energized with no call for heat. Check gas valve and gas valve wiring.

11 RED FLASHES: This indicates that a primary or auxiliary limit switch has opened its normally-closed contacts and has remained open for more than five minutes. This condition is usually caused by a failed blower motor or blower wheel.

12 RED FLASHES: This code indicates an open igniter circuit, which could be caused by a disconnected or loose wire or by a cracked or bro- ken igniter.

STEADY ON RED: Control failure. Replace control board.

60-MINUTE AUTOMATIC RESET FROM LOCKOUT: This control includes a “watchdog” type circuit that will reset from a lockout condition after 60 minutes. Operational faults 6,7,8 will be reset. This provides protection to an unoccupied structure if a temporary condition exists causing a furnace malfunction. An example would be a low incoming gas supply pressure preventing unit operation. When the gas pressure is restored, at some point the “watchdog” would restart the unit and pro- vide heat for the house.

NOTE: If a flame is detected the control flashes the LED for 1/8 of a second and then enters a flame stabilization period.

IGNITION CONTROL

Normal flame sense current is approximately

3.7 microamps DC (µa)

Low flame signal warning starts at 1.5 microamps.

Low flame signal control lockout point is

0.1 microamps DC (µa)

DIAGNOSTIC FAULT CODE STORAGE AND RETRIEVAL

The control in this furnace is equipped with memory that will store up to five error codes to allow a service technician to diagnose problems more easily. This memory will be retained even if power to the furnace is lost. This feature should only be used by a qualified service tech- nician.

The control stores up to five separate error codes. If more than five error codes have occurred since the last reset, only the five most recent will be retained. The furnace control board has a button, labeled "LAST ERROR" that is used to retrieve error codes. This function will only work if there are no active thermostat signals. So any call for heating, cooling or continuous fan must be terminated before attempting to retrieve error codes.

To retrieve the error codes, push the LAST ERROR button. The LED on the control will then flash the error codes that are in memory, starting with the most recent. There will be a two-second pause between each flash code. After the error codes have all been displayed, the LED will resume the normal slow green flash after a five second pause. To repeat the series of error codes, push the button again.

If there are no error codes in memory, the LED will flash two green flashes. To clear the memory, push the LAST ERROR button and hold it for more than five seconds. The LED will flash three green flashes when the memory has been cleared, then will resume the normal slow green flash after a five-second pause.

Thermostat Calling for Heat

(Seconds)

0 2

Fan on Delay 30 Seconds

THERMOSTAT

OFF

INDUCER

OFF

Thermostat Satisfied

OFF
15 Sec.	OFF
Post
Purge

IGNITOR OFF

MAIN VALVE

OFF

HUMIDIFIER

OFF

ELECTRONIC

AIR CLEANER

OFF

CIRCULATING

BLOWER OFF

OFF

60, 90, 120, 180 SEC. OFF Selectable Fan Off Delay

FIGURE 7: Furnace Control Event Schedule

Unitary Products Group

FL9s UP, FC9s Up, PS9 Up specifications

White Rodgers has long been synonymous with innovation in the HVAC industry, and its series of thermostats, including the FC9s Up, PS9 Up, and FL9s Up, exemplify this commitment to quality and technology. These programmable thermostats are designed to enhance energy efficiency, comfort, and control for both residential and commercial applications.

The FC9s Up is a standout in the lineup, featuring a user-friendly interface that makes it easy for homeowners to program their heating and cooling schedules. It supports multi-stage heating and cooling systems, allowing for precise temperature control across various zones. Its Smart Set technology enables the thermostat to learn users' habits over time, automatically adjusting to optimize energy use without sacrificing comfort. Furthermore, the FC9s Up is compatible with a range of home automation systems, offering seamless integration for tech-savvy users.

The PS9 Up brings another layer of versatility with its advanced sensor technology. This model is particularly notable for its responsive touch screen and intuitive controls. The PS9 Up is designed to monitor humidity levels, adjusting the operation of HVAC systems accordingly, which not only conserves energy but also enhances indoor air quality. Users can customize settings to align with their lifestyle, ensuring comfort throughout the day and night.

Lastly, the FL9s Up stands out with its robust features tailored for commercial applications. It provides advanced analytics that allow business owners to monitor and manage energy consumption effectively. The FL9s Up’s compatibility with various heating and cooling systems, including geothermal and radiant floor heating, makes it a versatile choice for larger or more complex environments. Moreover, its built-in Wi-Fi capability enables remote access via a smartphone or tablet, allowing users to control their systems from anywhere, ensuring optimal conditions even when they're away.

Together, the FC9s Up, PS9 Up, and FL9s Up represent the evolution of thermostat technology, backed by White Rodgers' decades of experience and commitment to efficiency. Each model offers unique features and capabilities tailored to different needs and environments, ultimately making temperature management more accessible and energy-efficient for users everywhere. Whether for residential or commercial applications, these thermostats set a high standard in the HVAC industry, driving energy savings and enhancing comfort with every use.