Troubleshooting, Reset Operation | White Rodgers 1F97-1277 specification

TROUBLESHOOTING

Reset Operation

Note: When thermostat is reset, installer configuration menu settings and programming will reset to factory settings.

If a voltage spike or static discharge blanks out the display or causes erratic thermostat operation, you can reset the thermostat by removing the wires from terminals R and C (do not short them together) and removing batteries for 2 minutes. After resetting the thermostat, replace the wires and batteries. If the thermostat has been reset and still does not function correctly contact your heating/cooling service person or place of purchase.

Note: Be sure to review the installer configuration menu settings.

To reset the programming, clock and configuration settings, pressand and the SYSTEM button simultaneously. The thermostat should go blank and then all segments will be displayed momentarily.

Symptom	Possible Cause		Corrective Action

No Heat/No Cool/No Fan	1.	Blown fuse or tripped circuit breaker.	Replace fuse or reset breaker.
(common problems)	2.	Furnace power switch to OFF.	Turn switch to ON.
	3.	Furnace blower compartment door or	Replace door panel in proper position to engage safety
		panel loose or not properly installed.	interlock or door switch.
	4.	Loose connection to thermostat or system.	Tighten connections.

No Heat	1.	Pilot light not lit.	Re-light pilot.
	2.	Furnace Lock-Out Condition. Heat	Many furnaces have safety devices that shut down when a
		may also be intermittent.	lock-out condition occurs. If the heat works intermittently
			contact the furnace manufacturer or local HVAC service
			person for assistance.
	3.	Heating system requires service or	Diagnostic: Set SYSTEM Switch to HEAT and raise the
		thermostat requires replacement.	setpoint above room temperature. Within a few seconds
			the thermostat should make a soft click sound. This sound
			usually indicates the thermostat is operating properly. If
			the thermostat does not click, try the reset operation listed
			above. If the thermostat does not click after being reset
			contact your heating and cooling service person or place
			of purchase for a replacement. If the thermostat clicks,
			contact the furnace manufacturer or a HVAC service
			person to verify the heating is operating correctly.

No Cool	1.	Cooling system requires service or	Same as diagnostic for No Heat condition except set the
		thermostat requires replacement.	thermostat to COOL and lower the setpoint below the
			room temperature. There may be up to a five minute delay
			before the thermostat clicks in Cooling.

Heat, Cool or Fan	1.	Possible short in wiring.	Check each wire connection to verify they are not shorted
Runs Constantly	2.	Possible short in thermostat.	or touching together. No bare wire should stick out from
	3.	Possible short in heat/cool/fan system.	under terminal block. Try resetting the thermostat as
	4.	FAN Switch set to Fan ON.	described above. If the condition persists the manufacturer
			of your system or service person can instruct you on how
			to test the Heat/Cool system for correct operation. If the
			system operates correctly, replace the thermostat.

Thermostat Setting &	1.	Thermostat thermometer setting	The thermometer can be adjusted +/- 4 degrees. See
Thermostat Thermometer		requires adjustment.	Temperature Display Adjustment in the Configuration
Disagree			Menu section.

Furnace (Air Conditioner)	1.	The location of the thermostat and/or	Digital thermostats provide precise control and cycle faster
Cycles Too Fast or Too Slow		the size of the Heating System may	than older mechanical models. The system turns on and
(narrow or wide		be influencing the cycle rate.	off more frequently but runs for a shorter time so there is
temperature swing)			no increase in energy use. If you would like an increased
			cycle time, choose SL for slow cycle in the Configuration
			menu, step 6 (heat) or 7 (cool). If an acceptable cycle rate
			is not achieved, contact a local HVAC service person for
			additional suggestions.

Forgot Keypad			Press the menu button (button will disappear) and hold in
Lockout Code			for 20 seconds. This unlocks the thermostat.

White-Rodgers is a division of Emerson Electric Co.

The Emerson logo is a trademark and service mark of Emerson Electric Co.

HOMEOWNER HELP LINE: 1-800-284-2925

www.white-rodgers.com

1F97-1277 specifications

The White Rodgers 1F97-1277 is an advanced programmable thermostat designed for residential heating and cooling systems. This model exemplifies the perfect blend of functionality and user-friendliness, offering homeowners a reliable way to manage their indoor climate effectively.

One of the standout features of the 1F97-1277 is its intuitive interface. The large, easy-to-read LCD display allows users to quickly view and adjust settings without the frustration often associated with traditional thermostats. The screen includes backlighting, ensuring visibility even in low-light conditions.

The unit is programmable, providing users the flexibility to create customized heating and cooling schedules. With up to seven-day programming, homeowners can tailor their settings according to personal routines. This level of customization not only enhances comfort but also contributes to energy savings, as systems can be set to reduce heating or cooling when the home is unoccupied.

White Rodgers has integrated a variety of technologies into the 1F97-1277 to improve performance and user experience. The thermostat features an auto-changeover function, which allows it to seamlessly switch between heating and cooling modes depending on the indoor temperature. This functionality minimizes the need for manual adjustments, ensuring optimal comfort throughout the year.

Another important characteristic of this model is its compatibility with a range of HVAC systems. It supports single-stage and multi-stage heating and cooling systems, as well as heat pumps, making it a versatile choice for a variety of homes. The 1F97-1277 also includes FARS (Fresh Air Reduction System) technology, which monitors indoor air quality and adjusts operations to enhance ventilation.

Energy efficiency is further bolstered through the presence of smart recovery technology. This feature enables the thermostat to anticipate the time needed to reach the desired temperature, allowing the HVAC system to operate less while still maintaining comfort levels.

Overall, the White Rodgers 1F97-1277 represents a modern solution for temperature control. With its combination of user-friendly design, programmable capabilities, and advanced technologies, it stands out as an exceptional choice for anyone looking to improve home comfort while managing energy costs efficiently. The reliability and flexibility of this thermostat make it an invaluable tool for today’s homeowners.