OPERATING YOUR THERMOSTAT
Choose the Fan Setting (Auto or On)
Set the FAN Switch to Auto or On.
Fan Auto is the most commonly selected setting and runs the fan only when the heating or cooling system is on.
Fan On runs the fan continuously for increased air circulation or to allow additional air cleaning.
Choose the System Setting
(Heat, Off, Cool, Auto)
Press the SYSTEM button to select:
Heat: Thermostat controls only the heating system.
Off: Heating and Cooling systems are off.
Cool: Thermostat controls only the cooling system.
Auto: Auto Changeover is used in areas where both heating and cooling may be required on the same day. AUTO allows the thermostat to automatically select heating or cooling depending on the indoor temperature and the selected heat and cool temperatures. When using AUTO, be sure to set the Cooling temperatures more than 1° Fahrenheit higher than the heating temperature.
Manual Operation for
Non-Programmable Thermostats
Press the SYSTEM button to select Heat or Cool and use the
or
buttons to adjust the temperature to your desired setting. After selecting your desired settings you can also press the SYSTEM button to select AUTO to allow the thermostat to automatically change between Heat and Cool.
IMPORTANT!
Manual Operation (Bypassing the Program) Programmable Thermostats
Press
or
and the HOLD button, then adjust the temperature wherever you like. This will override the pro- gram. The HOLD feature bypasses the program and allows you to adjust the temperature manually, as needed. What- ever temperature you set in HOLD will be maintained 24 hours a day, until you manually change the temperature or press Run Schedule to cancel HOLD and resume the programmed schedule.
Program Override (Temporary Override)
Press
or
buttons to adjust the temperature. This will override the temperature setting for a (default) four hour override period. The override period can be shortened by pressing
or lengthened by pressing 
. Program Override period can range from 15 minutes to 7 days.
Example: If you turn up the heat during the morning pro- gram, it will be automatically lowered later, when the tempo- rary hold period ends. To cancel the temporary setting at any time and return to the program, press Run Schedule.
If the SYSTEM button is pressed to select AUTO the thermostat will change to Heat or Cool, whichever ran last. If it switches to heat but you want cool, or it changes to cool but you want heat, press both
and
buttons simulta- neously to change to the other mode.
PROGRAMMING
Set Current Time and Day
1)Press Menu and then Set Time button once. The display will show the hour only.
2)Press and hold either the
or
key until you reach the correct hour and AM/PM designation (AM begins at midnight, PM begins at noon).
3)Press Set Time once again. The display window will show the minutes only.
4)Press and hold either the
or
key until you reach the correct minutes.
5)Press Set Time once again. The display will show the day of the week.
6)Press the
or
key until you reach the current day of the week.
7)Press Run Schedule once. The display will show the correct time and room temperature alternately.
Programming Tip: Copy Button
You may copy any daily program to another day or group of days by pressing the Copy button. In 7 day programming mode when the Copy button is pressed, the other 6 days of the week will flash. To copy the current program into the remaining six days, simply press the Copy button again. To copy the current program to another day of the week, press Advance Day to select the day and press Copy to paste the program. In 5/1/1 day programming mode the copy function is similar. The weekday
Fill in the blank schedule on the next page then:
Enter the Heating Program
1)Press the Menu button and then press Set Schedule. Press SYSTEM button to select "Heat" in the system switch area indicating the active mode being pro- grammed.
2)The top of the display will show the day(s) being pro- grammed. The time and set at temperature are also displayed. "Morning" will also be displayed to indicate the period.
3)Press
or
key to change the temperature to your selected temperature for the 1st heating period (Morning).
4)Press
or
key to adjust the start time for period.
5)The time will change in 15 minute increments.
6)After you have set the time and the temperature for the period to begin, press Set Schedule to advance to the next program period.
7)Repeat steps 2 through 6 until all of the program times and temperatures are set for all program periods on that day.
8)Press "Advance Day" to change to the next day and repeat steps 2 through 8.
9)When programming is complete and all of the times and temperatures match your desired heating schedule, press Run Schedule. The thermostat will now run your program.
Enter the Cooling Program
1)Press SYSTEM button to select "Cool" in the system switch area indicating the active mode being pro- grammed.
2)Follow Enter Heating Program instructions for entering cooling times and temperatures.
6