Heat & Glo LifeStyle CF230E-B, CF260E-B owner manual As an Insert, Pre-installation Preparation

Page 10

B. As an Insert

Pre-installation Preparation

This insert and its components are tested and safe when in- stalled in accordance with this manual. Report to your dealer any parts damaged in shipment, particularly the condition of the glass. Do not install any heater with damaged, in- complete or substitute parts.

WARNING

Fire Risk

•Do not install or operate damaged heater.

•Do not modify heater.

•Installation other than as instructed by Hearth & Home Technologies Inc. is strictly prohibited.

•Do not operate the heater without fully assembling all components.

•Installation and/or use of any component part not approved by Hearth & Home Technologies.

Hearth & Home Technologies disclaims any responsibility for, and the warranty and agency listing will be voided by the above actions.

•A retaining method may be needed to secure the heater in place.

•Combustible facing material may be installed over the original combustible or noncombustible facing material on the solid fuel fi replace. The original specifi ed clearances of a factory-built fireplace must be maintained, with the exception of the hearth. Clearances on a masonry fi replace must be maintained at 12 in. from the opening for combustible projections over 1-1/2 in. Clearances for combustible projections under 1-1/2 in. must be maintained per NFPA 211. Plan the surround size accordingly. A front face must be used with the insert.

•The insert front face is tested and approved with this insert and may cover existing air circulation vents or grilles on the solid fuel fi replace it is installed into. Should the face not cover the entire ventilation grille surface, the grille should be left open.

•The solid fuel fi replace’s fl ue damper must be fully locked in the closed position or removed for installation.

Note: Decorative trim front faces have been tested and approved to cover existing air circulation vents or grills.

•The chimney must be capped.

•Install the insert without the front face and make all electrical connections.

Installation

•These inserts are designed for installations into solid fuel masonry or factory built noncombustible fi replaces that have been installed in accordance with the national, provincial, state or local building codes.

•You should seal off the area between the termination cap and the top of the existing chimney opening to avoid down drafts, moisture and/or cold air problems.

•Minimum fi replace opening requirements are shown in Figures 3.1 and 3.2 of this installation manual. The firebrick (refractory) can be removed from a factory built fi replace in order to gain minimum insert opening requirements.

•This insert requires no hearth extensions. Combustible material on the floor may be installed up to the insert. Do not obstruct the lower grill of the insert. The original fi replace cannot be returned to solid fuel in this condition.

•The metal fl oor of the solid fuel fi rebox may be removed to facilitate the installation of the insert. The side walls and top structure of the fi rebox may not be altered with the exception of removable baffl es and dampers. The original fi replace cannot be returned to solid fuel in this condition.

•Position, Level and Secure Insert

•Place the heater into position.

•Level the heater from side to side and from front to back. If necessary, use the leveling bolts included in the manual bag. Screw the bolts into the nuts installed in the bottom of the insert (see replacement parts diagram). Turn bolts in until the insert is level.

Note: The warning label above, located in the instruction package, must be affi xed to the lower back wall of the existing fi replace prior to installation of the insert.

Note: When the front is installed it will cover the gap between the heater and the framing, cabinet, finishing materials or existing fi replace.

10

Heat & Glo • CF230E-B & CF260E-B • 4038-894 Rev C • 11/05

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Models CF230E-B CF260E-B Electric Fireplace/Insert Homeowner Reference Information Listing Label Information/LocationTable of Contents Important Instructions Listing and Code ApprovalsCertification Fire RiskGetting Started Tools and Supplies NeededClearances Framing and ClearancesSelecting Heater Location Electrocution RiskModel # Heater LocationsFrame the Heater Framing the HeaterShock Risk InstallationAs a Fireplace Shock Risk Fire RiskPre-installation Preparation As an InsertDescription WiringAmps Watts 120/208/240Orange 3 PIN Install the Front Face AccessoriesInstall other Optional Accessories Finishing Material Finishing ChecklistFinishing MantelOperating Instructions Main Power SwitchThermostat Troubleshooting Guide TroubleshootingIssues Possible Causes Solutions Clean the Firebox Compartment Maintenance and ServiceAccess the Firebox Clean the Back Acrylic PanelMaintenance Task List When cleaning glass doorHeater Dimensions Reference MaterialsRemote Control Optional ComponentsCF230E-B CF260E-BService Parts CF230E-B, CF260E-BThermostat Control Assembly Hearth Assembly23/26 Log Assembly Description of Part CF230E-B CF260E-B QtyThis page intentionally left blank Warranty Limited WarrantyContact Information

CF260E-B, CF230E-B specifications

The Heat & Glo LifeStyle CF230E-B and CF260E-B are two exceptional gas fireplace models that embody modern design and cutting-edge technology, suited for contemporary living spaces. Both models deliver an efficient heating solution while enhancing the aesthetic appeal of any room.

One of the standout features of the CF230E-B and CF260E-B is their sleek, clean face design. This minimalist style allows for a seamless integration into various interior design schemes, making them perfect focal points for modern homes. The elegant ember bed radiates warmth and ambiance, creating a cozy atmosphere perfect for gatherings or relaxation.

Both models utilize advanced technology to ensure optimal performance. The IntelliFire Touch ignition system provides an easy-to-use, battery-operated solution for lighting the fireplace. This user-friendly feature not only simplifies operation but also enhances safety by eliminating the need for matches or lighter tools.

In terms of efficiency, the LifeStyle series promotes heat distribution technology that ensures consistent warmth throughout your living space. With adjustable heat settings, users have the flexibility to customize their comfort level while maintaining efficient energy use. The CF260E-B model, in particular, boasts a higher BTU output, making it a suitable choice for larger areas needing substantial heating.

The environmental impact is also a consideration with the LifeStyle fireplaces. Both models are designed to minimize emissions without compromising on performance. Their focus on efficiency aligns with the growing demand for eco-friendly heating solutions.

Another notable aspect of these fireplaces is the customizable flame and ember bed options. Users can choose from a variety of log sets, colors, and flame heights, allowing for personalized design and ambiance to match individual preferences.

Safety is paramount in the design of the CF230E-B and CF260E-B. They come equipped with a safety screen and a reliable shut-off valve to prevent overheating and ensure peace of mind, especially in homes with pets or children.

In summary, the Heat & Glo LifeStyle CF230E-B and CF260E-B models are a blend of aesthetic appeal, advanced technology, and eco-friendly performance. With their stylish designs, efficient heating capabilities, and user-friendly features, they stand out as exceptional choices for homeowners looking to enrich their spaces with warmth and elegance. Whether for intimate settings or larger gatherings, these fireplaces are poised to enhance comfort and sophistication in any home.
Top Page Image Contents