Troubleshooting, Reset Operation | White Rodgers 1F95-1280 guide

TROUBLESHOOTING

Reset Operation

Note: When thermostat is reset, installer conﬁ guration menu settings and programming will reset to factory settings.

If a voltage spike or static discharge blanks out the display or causes erratic thermostat operation, you can reset the thermo- stat by removing the wires from terminals R and C (do not short them together) and removing batteries for 2 minutes. After resetting the thermostat, replace the wires and batteries. If the thermostat has been reset and still does not function correctly contact your heating/cooling service person or place of purchase.

Note: Be sure to review the installer conﬁ guration menu settings.

To reset the programming, clock and conﬁguration settings, press the and and SYSTEM keys simultaneously. The thermostat should go blank and then all segments will be displayed momentarily.

Symptom	Possible Cause		Corrective Action

No Heat/No Cool/No Fan	1.	Blown fuse or tripped circuit breaker.	Replace fuse or reset breaker.
(common problems)	2.	Furnace power switch to OFF.	Turn switch to ON.
	3.	Furnace blower compartment door or	Replace door panel in proper position to engage safety
		panel loose or not properly installed.	interlock or door switch.
	4.	Loose connection to thermostat or system.	Tighten connections.

No Heat	1.	Pilot light not lit.	Re-light pilot.
	2.	Furnace Lock-Out Condition. Heat	Many furnaces have safety devices that shut down when
		may also be intermittent.	a lock-out condition occurs. If the heat works intermittently
			contact the furnace manufacturer or local HVAC service
			person for assistance.
	3.	Heating system requires service or	Diagnostic: Set SYSTEM Switch to HEAT and raise the
		thermostat requires replacement.	setpoint above room temperature. Within a few seconds
			the thermostat should make a soft click sound. This sound
			usually indicates the thermostat is operating properly. If
			the thermostat does not click, try the reset operation listed
			above. If the thermostat does not click after being reset
			contact your heating and cooling service person or place
			of purchase for a replacement. If the thermostat clicks,
			contact the furnace manufacturer or a HVAC service
			person to verify the heating is operating correctly.

No Cool	1.	Cooling system requires service or	Same as diagnostic for No Heat condition except set the
		thermostat requires replacement.	thermostat to COOL and lower the setpoint below the
			room temperature. There may be up to a ﬁ ve minute delay
			before the thermostat clicks in Cooling.

Heat, Cool or Fan	1.	Possible short in wiring.	Check each wire connection to verify they are not shorted
Runs Constantly	2.	Possible short in thermostat.	or touching together. No bare wire should stick out from
	3.	Possible short in heat/cool/fan system.	under terminal block. Try resetting the thermostat as de-
	4.	FAN Switch set to Fan ON.	scribed above. If the condition persists the manufacturer
			of your system or service person can instruct you on how
			to test the Heat/Cool system for correct operation. If the
			system operates correctly, replace the thermostat.

Thermostat Setting &	1.	Thermostat thermometer setting	The thermometer can be adjusted +/- 4 degrees. See
Thermostat Thermometer		requires adjustment.	Temperature Display Adjustment in the Conﬁ guration
Disagree			Menu section.

Furnace (Air Conditioner)	1.	The location of the thermostat and/or	Digital thermostats provide precise control and cycle
Cycles Too Fast or Too Slow		the size of the Heating System may	faster than older mechanical models. The system turns
(narrow or wide		be inﬂ uencing the cycle rate.	on and off more frequently but runs for a shorter time
temperature swing)			so there is no increase in energy use. If you would like
			an increased cycle time, choose SL for slow cycle in the
			Conﬁ guration menu, step 7 (heat) or 8 (cool). If an ac-
			ceptable cycle rate is not achieved, contact a local HVAC
			service person for additional suggestions.

Forgot Keypad			Press the menu key (key will disappear) and hold in for
Lockout Code			20 seconds. This unlocks the thermostat.

Blank display any or keypad	1. Voltage Spike or static discharge		Use the Reset Operation shown above.
not responding

"Call for Service" on display	Power applied to thermostat "L" terminal		Indicates the heat pump system is sending a signal (volt-
			age) to the thermostat terminal marked "L". It does not
			indicate a malfunction in the thermostat. The manufac-
			turer of the Heat Pump system can determine the likely
			cause of Call for Service on the thermostat by identifying
			the component in the system sending power to the "L"
			terminal.

1F95-1280 specifications

The White Rodgers 1F95-1280 is a sophisticated and versatile thermostat designed for modern households seeking enhanced climate control and energy efficiency. As a prominent product from White Rodgers, a brand known for its commitment to quality and innovation in the HVAC industry, the 1F95-1280 combines advanced technology with user-friendly features.

One of the standout characteristics of the White Rodgers 1F95-1280 is its digital touchscreen interface. This easy-to-navigate display allows users to effortlessly adjust their heating and cooling settings with a simple tap. The vibrant screen not only provides clear visibility but also displays pertinent information regarding current temperatures, setpoints, and system statuses, making it intuitive for users of all ages.

The thermostat is equipped with programmable scheduling capabilities, allowing homeowners to set tailored heating and cooling schedules based on their daily routines. This feature enables significant energy savings, as users can program the thermostat to automatically adjust temperatures when they are away from home or asleep. The flexibility of up to 4 programmable periods per day ensures optimal comfort while minimizing energy waste.

Connectivity is another key feature of the 1F95-1280. The thermostat supports Wi-Fi connectivity, enabling users to control their home's climate remotely via a smartphone app. This feature not only provides convenience but also the ability to monitor energy usage and make adjustments on the go, ensuring that the home is always at the desired temperature upon arrival.

In addition to its smart capabilities, the White Rodgers 1F95-1280 boasts compatibility with various heating and cooling systems, including gas, oil, and electric systems, making it a versatile choice for diverse home setups. The device also supports multistage heating and cooling, providing smooth operation in more complex HVAC systems.

Energy efficiency is prioritized with features like the energy-saving mode, which intelligently adjusts settings to reduce consumption without sacrificing comfort. The thermostat also comes equipped with a filter change reminder, helping maintain optimal system performance by ensuring that air filters are replaced regularly.

Overall, the White Rodgers 1F95-1280 is a comprehensive thermostat solution that combines advanced features, user-friendly design, and energy-saving technologies. Whether for those looking to upgrade their existing system or seeking a reliable way to enhance home comfort, the 1F95-1280 stands out as a leading choice in modern climate control.