White Rodgers 1F95-1280 specifications Record the number you select for future use

INSTALLER/CONFIGURATION MENU

14.Select °F or °C Readout – Changes the display readout to Celsius or Fahrenheit as required.

15.Select Audio Prompting (Beeper) On or Off – Factory default setting is b, On. If you wish to turn off the beeper select OFF.

16.Select Daylight Saving Time Calculation – This feature will allow the thermostat to calculate the DST automati- cally and apply it to the Real Time Clock display. Default is On.

17 & 18. Select Automatic Schedule – This feature allows programming a “Comfort Temperature” into all program periods with the Auto Schedule key. When Heat AS (for Heat mode) or Cool AS (for Cool mode) is selected On, the Auto Schedule feature is ready to be set. Off indicates that the feature is not ready to be used or a “Comfort Temperature" is already set. See Auto Schedule in Programming section.

19.Select Cool Savings™: Cool Savings allows you to select a temperature offset (from 1-6 degrees). When the compressor runs for long periods, the thermostat will internally slowly/gradually adjust the room temperature display lower, subtracting a maximum of the number of degrees you select.

This energy saving feature is based on the principal that long compressor run times lower indoor humidity and make a slightly higher temperature feel comfortable. Cool Savings operates only when the compressor runs 20 minutes or longer, normally on the hottest summer days. When Cool Savings is operating the thermostat will fl ash "Cool Savings" to indicate it is slowly adjusting the display temperature lower.

20.Heat Temperature Limit Range – This feature adjusts the highest setpoint temperature for heat. The default setting is 99°F. It can be changed to a setting between 62°F and 98°F. Temperature Limit" icon will be displayed to the left of your setpoint temperature when using this feature. "Temperature Limit" icon will fl ash if an attempt is made to adjust the temperature beyond the range selected.

21.Cool Temperature Limit Range – This feature adjusts the lowest setpoint temperature for cool. The default setting is 45°F. It can be changed to a setting between 46°F and 82°F. "Temperature Limit" icon will be dis- played to the left of your setpoint temperature when using this feature. "Temperature Limit" icon will fl ash if an attempt is made to adjust the temperature beyond the range selected.

22.Keypad Lockout – This step allows you to select the

type of lockout or limited range security required. If no lockout or limited range security is required, press to advance the menu.

Three security settings are available in this menu item. Use the or keys to select the lockout desired. Lockout selections are:

"Keypad Lockout and L" = Total Lockout. Total Lockout locks all keys.

"Keypad Lockout and P" = Partial Lockout. Partial Lock- out allows only the or keys to operate within your set temperature limits.

"Temperature Limit/Keypad Lockout" prevents chang- ing the temperature limits in the Confi guration Menu.

After the type of lockout is selected, press .

Keypad Lockout Combination Number Selection Display will read "000" "Keypad Lockout".

Skip this step and continue through the remainder of the confi guration menu if you require an Air Filter Change out indicator or Humidifi er Pad Change out indicator by pressing the key to advance.

Return to this point when you are ready to start your selected lock-out and continue by:

Pressing or keys to select your keypad lockout combination number. Note: "000" is not a valid combina- tion choice.

Record the number you select for future use.

Press to exit the menu. The security feature you select will start in 10 seconds. The system key will remain active for 10 seconds to allow setting Heat, Off, Cool or Auto.

To unlock the keypad, press Menu, then press Installer Confi g. Display will show "000" and keypad lock. Enter the code used to lock the keypad and press .

23 & 24. Select Fast Second Stage, ON or OFF – Selecting FA ON forces additional heat stages to come on quickly when is used to raise the temperature a few degrees above the room. Select this setting if you want the heat to increase quickly when you manually raise the tempera- ture.

Selecting FA OFF allows the thermostat to calculate an optimal time to bring on additional stages of heat. When the is used to raise the setting above the room tem- perature additional heat stages may come on very quickly or very slowly (up to 30 minutes later) depending on recent system performance. Select this setting if you do not require the additional heat stages to come on quickly when you manually raise the setting and want to allow the thermostat to stage based on recent system performance.

The Fast Cool feature operates the cooling stages in the same manner as Fast Heat, On or Off when the tempera- ture is lowered below the room setting.

25.Select Remote Temperature Sensor – Allows one wired remote temperature sensor (indoor, F145-1328, or outdoor, F145-1378) be connected to it and indicates the measured temperature in clock digits. This item allows you to select the remote sensor and also confi gure it as indoor or outdoor temperature sensor. Factory default is off. Select Remote On and Remote in (for indoor) or Outdoor Remote.

Local Temperature Sensor Disable – This is applicable only when indoor remote temperature sensor is enabled.

Factory default is On LS. You can make it Off LS if de- sired by using or touch keys. Then, only the indoor remote temperature reading will be used for control.

26.Select Dual Fuel Feature With No Outdoor Sensor (dF) – This feature is applicable only in heat pump modes and with no outdoor sensor. When selected ON, the thermostat will use software logic to determine when to switch to gas heat and shut down the compressor.

7