Operating Your Thermostat

Check Thermostat Operation

NOTE

To prevent static discharge problems, touch side of thermostat to release static build-up before touching any keys.

If at any time during testing your system does not operate properly, contact a qualified service person..

Fan Operation

If your system does not have a G terminal connection, skip to

Heating System.

1.Turn on power to system..

2.Press fan key to ON position.. The blower should begin to operate..

3.Press fan key to AUTO position.. The blower should stop immediately..

!CAUTION

Do not allow the compressor to run unless the com- pressor oil heaters have been operational for 6 hours and the system has not been operational for at least 5 minutes.

Heating

1.Press SYSTEM key to select HEAT.. If the auxiliary heating system has a standing pilot, be sure to light it..

2.Press to adjust thermostat setting to 1° above the room temperature.. The heat pump system should begin to oper- ate.. The display should show "System On".. However, if the system configuration is set to HP1 or HP2 and setpoint temperature display is flashing, the 5 minute compressor lockout feature is operating (see Configuration menu, item 11)..

3.Adjust temperature setting to 3° above room temperature.. If your system configuration is set at MS2, HP1 or HP2, the auxiliary heat system should begin to operate and the display will show "System On +2"..

4.Press to adjust the thermostat below room tempera- ture.. The heating system should stop operating..

Emergency Mode

Applies only to Heat Pump Systems

Emergency Heat (System EM Position) bypasses the Heat Pump to use the heat source wired to terminal W/E, W2 on the thermostat.. EM is typically used when compressor opera- tion is not desired, or you prefer back-up heat only..

1.Press SYSTEM key to select EM.. “EM Heat Mode” will flash on the display..

2.Press to adjust thermostat setting above room tem- perature.. The Emergency heating system will begin to operate.. The display will show “System On” flashing “EM Heat Mode” and “Heat” to indicate that the Emergency sys- tem is operating..

3.Adjust temperature setting to 3° above room temperature.. Any additional stages of auxiliary heat should begin to operate and the display will show "System On +2"..

4. Press to adjust the thermostat below room tempera- ture.. The heating system should stop operating..

!CAUTION

To prevent compressor and/or property damage, if the outdoor temperature is below 50°F, DO NOT operate the cooling system.

Cooling

1.Press SYSTEM to select COOL..

2.Press to adjust the thermostat setting below room tem- perature.. The blower should come on immediately on high speed, followed by cold air circulation.. The display should show "System On".. If the setpoint temperature display is flashing, the compressor lockout feature is operating (see Configuration menu, item 5)..

3.Adjust temperature setting to 3° below room temperature.. The second stage cooling should begin to operate and the display should show "System On +2"..

4.Press to adjust the temperature setting above room temperature.. The cooling system should stop operating..

Choose the Fan Setting (Auto or On)

Fan Auto is the most commonly selected setting and runs the fan only when the heating or cooling system is on..

Fan On selection runs the fan continuously for increased air circulation or to allow additional air cleaning..

Choose the System Setting

(Cool, Off, Heat, Em, Auto)

Press the SYSTEM key to select:

Cool: Thermostat controls only the cooling system..

Off: Heating and Cooling systems are off..

Heat: Thermostat controls only the heating system..

Em: Setting is available only when the thermostat is config- ured in HP1 or HP2 mode..

Auto: Auto Changeover is used in areas where both heating and cooling may be required on the same day.. AUTO allows the thermostat to automatically select heating or cooling depending on the indoor temperature and the selected heat and cool temperatures.. When using AUTO, be sure to set the Cooling temperatures more than 1° Fahrenheit higher than the heating temperature..

Manual Operation for

Non-Programmable Mode

Press the SYSTEM key to select Heat or Cool and use the or to adjust the temperature to your desired setting.. After selecting your desired settings you can also press the SYSTEM key to select AUTO to allow the thermostat to auto- matically change between Heat and Cool..

Manual Operation (Bypassing the Program) Programmable Mode

Manual operation will bypass the program and allow you to adjust the temperature as you desire.. The temperature you set in Hold will be maintained indefinitely.. Press or to

1F95-1280 specifications

The White Rodgers 1F95-1280 is a sophisticated and versatile thermostat designed for modern households seeking enhanced climate control and energy efficiency. As a prominent product from White Rodgers, a brand known for its commitment to quality and innovation in the HVAC industry, the 1F95-1280 combines advanced technology with user-friendly features.

One of the standout characteristics of the White Rodgers 1F95-1280 is its digital touchscreen interface. This easy-to-navigate display allows users to effortlessly adjust their heating and cooling settings with a simple tap. The vibrant screen not only provides clear visibility but also displays pertinent information regarding current temperatures, setpoints, and system statuses, making it intuitive for users of all ages.

The thermostat is equipped with programmable scheduling capabilities, allowing homeowners to set tailored heating and cooling schedules based on their daily routines. This feature enables significant energy savings, as users can program the thermostat to automatically adjust temperatures when they are away from home or asleep. The flexibility of up to 4 programmable periods per day ensures optimal comfort while minimizing energy waste.

Connectivity is another key feature of the 1F95-1280. The thermostat supports Wi-Fi connectivity, enabling users to control their home's climate remotely via a smartphone app. This feature not only provides convenience but also the ability to monitor energy usage and make adjustments on the go, ensuring that the home is always at the desired temperature upon arrival.

In addition to its smart capabilities, the White Rodgers 1F95-1280 boasts compatibility with various heating and cooling systems, including gas, oil, and electric systems, making it a versatile choice for diverse home setups. The device also supports multistage heating and cooling, providing smooth operation in more complex HVAC systems.

Energy efficiency is prioritized with features like the energy-saving mode, which intelligently adjusts settings to reduce consumption without sacrificing comfort. The thermostat also comes equipped with a filter change reminder, helping maintain optimal system performance by ensuring that air filters are replaced regularly.

Overall, the White Rodgers 1F95-1280 is a comprehensive thermostat solution that combines advanced features, user-friendly design, and energy-saving technologies. Whether for those looking to upgrade their existing system or seeking a reliable way to enhance home comfort, the 1F95-1280 stands out as a leading choice in modern climate control.