Desa RGA 2-72 installation manual Testing Burner for Leaks, Adding PAN Material

Page 8

8

INSTALLATION

Continued

TESTING BURNER FOR LEAKS

1.Generously apply noncorrosive leak detection fluid to all connections.

WARNING: Never check for gas leaks with open flame.

2.Light the burner with the shutoff valve no more than half open and holding a match slightly in front of the pan (see Lighting Instructions, page 10).

3.Inspect all connections for bubbles, raw gas odor, or flame from any area other than the burner (leaks). If leaks are detected, shut off the gas valve immediately. Tighten, or reassemble the loose connection(s) using pipe joint compound until burner system is leak free.

4.When the burner is tested and leak free, observe the individual tongues of flame on the burner. Note: The burner design includes more ports on the outside of the bar. Make sure that all ports are clear and producing flame evenly across the burner. If any ports appear blocked, clear them by removing the burner manifold and reaming the ports with a modified paper clip or other suitable tool.

5.When finished testing, turn the gas shutoff valve OFF to ex- tinguish all flames.

ADDING PAN MATERIAL

1.Open the bag of ash bed material (vermiculite) and spread it evenly across the burner pan to the top. You may overflow the front and sides of the pan to cover the entire pan and connect- ing hardware. Do not cover GA9050A or GA9150A valve.

2.Open the glowing embers and evenly cover the ash bed material (vermiculite) in the burner pan.

INSTALLING THE GRATE AND LOGS

1.Place the grate over the burner pan where the two outer hori- zontal supports on the grate fit into the two pan positioning notches in the rear vertical edge of the pan.

Grate Steps

Grate

INSTALLATION

Testing Burner for Leaks

Adding Pan Material

Installing the Grate and Logs

2.Slide the two rear log grate steps over the two outer horizontal supports on the grate as shown in Figure 15.

3.Place the back log on the grate onto the grate steps (see Figure 16).

4.Place the front log(s) on the grate and slide forward against the front bars on the grate (see Figure 16).

5.Place the smaller top logs onto the bottom logs (see Figure 17). Leave as much open space between logs as possible to minimize flame impingement and sooting. Note: Logs may chip if they are handled roughly or if hit together while being placed.

Figure 16 - Installing Front and Back Logs (Number and style of your logs may vary)

Figure 15 - Installing Grate (Pan Material Not Shown)

Figure 17 - Placement of Top Logs

For more information, visit www.desatech.com

115043-01

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Brentwood What to do if YOU Smell GASTable of Contents Safety Information Local CodesUnpacking Product IdentificationInstallation Flue Opening SpecificationsVenting Specifications for Installation Installing Damper ClampInstallation Items Needed Hearth KIT Assembly and Installation Optional GA9050A ON/OFF Safety VALVE/ Pilot KIT AssemblyNatural Gas Installation Testing Burner for Leaks Adding PAN MaterialOperating Appliance Service Hints Technical ServiceReplacement Parts Cleaning MaintenanceTroubleshooting Observed Problem Possible CauseObserved Problem Possible Cause Remedy Troubleshooting Accessories Equipment Shutoff Valve GA5010Parts List and Illustrated Parts Breakdown Owners Registration Form Postage Required 115043-01 115043-01 Warranty Information Keep this Warranty

RGA 2-72 specifications

Desa RGA 2-72 is a notable residential development that epitomizes modern living through the integration of innovative technologies and sustainable features. This project is designed to cater to the diverse needs of families while promoting a sense of community and environmental responsibility.

One of the main features of Desa RGA 2-72 is its focus on eco-friendly living. The development incorporates green building materials and energy-efficient designs that minimize environmental impact. Each unit is equipped with solar panels, enabling residents to harness renewable energy, thus reducing reliance on traditional energy sources and lowering utility bills. This commitment to sustainability extends to rainwater harvesting systems, which help to conserve water and reduce waste.

The architectural design of Desa RGA 2-72 reflects contemporary aesthetics combined with functional layouts. The homes are designed with open-concept floor plans that maximize natural light and create spacious living environments. Large windows and high ceilings enhance the sense of space and openness, providing a comfortable and inviting atmosphere for residents.

Another key characteristic of this development is the incorporation of smart home technologies. Each unit comes equipped with smart thermostats, lighting controls, and security systems that can be easily managed through a mobile app. This automation not only enhances convenience but also contributes to energy savings, as residents can monitor and control their energy usage remotely.

Community amenities are also a significant aspect of Desa RGA 2-72. The development features landscaped green spaces, playgrounds for children, and recreational facilities designed to foster social interaction among residents. Walking and biking paths encourage outdoor activities, promoting a healthy lifestyle while strengthening community bonds.

Accessibility is another advantage of this development. Located near essential services, including schools, shops, and healthcare facilities, residents enjoy the convenience of urban living without sacrificing the tranquility of suburban life.

In conclusion, Desa RGA 2-72 stands out as a model for modern, eco-friendly residential living. With its focus on sustainability, smart technologies, and community-oriented design, it offers an attractive option for families seeking a harmonious blend of comfort, convenience, and environmental responsibility. This development not only meets the demands of contemporary living but also sets a standard for future residential projects.
Top Page Image Contents