Desa W32KCSA Assembling metal trim, Fireplace Installation, Installing Fireplace with Flange

Page 4

Assembling metal trim

1.Remove packaging from three pieces of metal trim.

2.Locate two adjusting plates with set screws, and two shims in the hardware packet.

3.Align shim under adjusting plate as shown in Figure 11.

4.Slide one end of adjusting plate/shim in slot on mitered edge of top trim (see Figure 11).

5.Slide other end of adjusting plate/shim in slot on mitered edge of side trim (see Figure 11).

6.While firmly holding edges of trim together, tighten both set screws on the adjusting plate with slotted screwdriver.

7.Repeat steps 2 through 6 for other corner.

Set Screws

Slot

Adjusting

Top Trim

 

Plate

Mitered Edge

Shim

Side Trim

 

Slot

Figure 11 - Assembling Metal Trim

Fireplace Installation

1.Fireplace should be fully assembled. See Assembling Fireplace in fireplace owner’s manual.

2.Place mantel base close to installation location. See fire- place owner’s manual for installation clearances. Leave enough room to get behind mantel once fireplace and mantel assembly have been attached to base if installing a fireplace with flange.

3.Install gas line. See Connecting to Gas Supply in fireplace owner’s manual. Remember to leave access to the gas shutoff valve somewhere on the base or where it is ac- cessible to the user.

4.Check for leaks. See Checking Gas Connections in fire- place owner’s manual.

Screw

(Side view for clarity)

Shoulder

Screw

Gas Line

Access Hole

Assembled

Shoulder

Possible

Metal Trim

Shutoff Valve

Screws

 

Locations

 

 

 

Mantel Base

 

Figure 12 - Installing Fireplace with Flange

IMPORTANT: If your fireplace has a nailing flange see Installing Fireplace with Flange. If your fireplace does not have a nailing flange see Installing Fireplace without Flange, page 5.

Installing Fireplace with Flange

1.

Place mantel assembly on wood base and center left to

 

right having back of assembly flush with back of base.

 

Mark placement on base along inside front of mantel

 

assembly. Remove mantel assembly from base.

2.

Position fireplace on base, centering left to right between mark-

 

ings. Carefully position gas lines. IMPORTANT: Use caution

 

when positioning fireplace on base as base may scratch.

3.

With assistance, carefully place mantel over fireplace

 

(see Figure 12). Fireplace nailing flanges will be to inside

 

of mantel. Align mantel with markings made previously.

Bracket with 1/2"-3/4" Screws

Mantel Base

Bracket with 1/2"-3/4" Screws

Make sure back of mantel is flush with back of mantel

base. Adjust fireplace as necessary.

4. Attach mantel to base using 1 1/4" screws through pocket

holes. Using brackets and 1/2" or 3/4" screws from

bracket hardware kit, attach brackets to base and mantel

assembly using one bracket at each back corner of leg

sides and one on each leg front (see Figure 13).

5. Adjust fireplace so that it fits into mantel opening properly.

Figure 13 - Installing Brackets to Mantel Base

www.desatech.com

119794-01A

Image 4
Contents W32KCSA and W32KPA Wall Mantel and Base with Trim Assembling Mantel Assembling Mantel TopAttaching Mantel Top Assembly to Header/Leg Assembly Attach Side/Front Assembly to Mantel TopInstalling Fireplace with Flange Fireplace InstallationAssembling metal trim Installing Fireplace without Flange Attaching Fireplace to Mantel and Mantel Base07/06

W32KPA, W32KCSA specifications

Desa W32KPA and W32KCSA are innovative heating solutions designed to address the growing demand for efficient and environmentally-friendly climate control systems. These devices are particularly notable for their advanced technology and user-friendly features.

One of the main features of the Desa W32KPA and W32KCSA is their high energy efficiency. Both units utilize cutting-edge heating technologies that significantly reduce energy consumption compared to traditional heating methods. This not only leads to lower utility bills for consumers but also contributes to a smaller carbon footprint, making them an environmentally responsible choice.

The W32KPA model is designed for more versatile heating applications, suitable for residential use, while the W32KCSA is tailored for larger spaces requiring efficient climate control. The adaptability of these models makes them ideal for a variety of settings, from homes and offices to workshops and warehouses.

A standout characteristic of both models is their advanced control systems. They come equipped with programmable thermostats that allow users to set their desired temperatures and schedules, resulting in optimal comfort and energy savings. Remote access capabilities are also available, empowering users to adjust settings from their smartphones or tablets, ensuring that their spaces are always at the perfect temperature.

Safety is another critical element in the design of the Desa W32KPA and W32KCSA. These units are equipped with multiple safety features, including overheat protection and automatic shut-off mechanisms, ensuring peace of mind for users.

Durability is also a hallmark of these heating solutions. Built with high-quality materials, the W32KPA and W32KCSA are designed to withstand the rigors of daily use while providing reliable performance over time. This longevity makes them a cost-effective investment for consumers looking to enhance their heating systems without the worry of frequent replacements.

In summary, the Desa W32KPA and W32KCSA are exemplary heating solutions that blend efficiency, safety, and modern technology. With their unique features and robust performance, they stand out in the market as reliable options for anyone looking to enhance their indoor climate control while supporting sustainable practices. Whether for residential or larger commercial applications, these models exemplify the future of heating technology.