Desa W32LS2 installation instructions Leg Assembly, Header Assembly, Mantel Top Assembly

Page 2

Leg Assembly

1.Lay right side panel (#2) face down on a soft surface to avoid marking finish. Attach four brackets with 1/2" screws to right side panel (#2) leaving screws slightly loose. Face brackets out toward tongued side (see Figure 1). Place right front leg over right side (#2) matching groove in leg to tongue on side, as shown in Figure 1. Align threaded holes with brackets on side. Start four 1/2" screws through brackets. Align bottom of side and leg assembly so they are flush with each other. Hold these pieces securely while tightening (but not over tightening) screws.

2.Assemble left side (#4) and left leg (#5) as described in step 1.

3.Attach 6 brackets to base (#1) at threaded hole locations using 1/2" screws leaving screws loose. Face brackets toward outside.

 

 

Bracket

Groove in

 

 

Leg Front

 

 

 

 

 

Leg Front (#3)

 

1

1/4" Screw

 

1/2" Screw

with Washer

 

 

 

Corbel

 

 

4.Place right side/leg assembly on base and align threaded holes with brackets. Start 1/2" screws through brackets into threaded holes in side/leg assembly. Back of side/ leg assembly should be flush with back of base. Assure alignment is correct and spaces are at a minimum and tighten leaving screws slightly loose.

5.Assemble left side/leg assembly to base (#1) following step #4.

Header Assembly

1.Start two 1 1/4" screws with washers through header as- sembly block (#8) into threaded inserts on right side of mantel. Repeat for left side (see Figure 3).

2.With arrow pointing up, place header (#6) into position on top of leg assemblies and against header assembly block (#8) (see Figure 3). Start two 1 1/4" screws with washers through header assembly blocks (#8) into threaded in- serts in header. Hold header in proper alignment with leg assemblies and tighten, leaving screws slightly loose.

1 1/4" Screw with Washer

Header (#6)

Header

Assembly

Block (#8)

Leg Side (#2)

Tongue on

Leg Side

Figure 1 - Leg Assemblies (right side shown)

Right

Side/Leg

Assembly

Base (#1)

Bracket

1/2" Screw

Figure 2 - Leg Assembly to Base

Header

 

Assembly

1 1/4" Screw

Block (#8)

with Washer

Figure 3 - Attaching Header

Mantel Top Assembly

Place mantel top (#7) on mantel assembly. Align back of top with back of sides. Using four 1 1/4" screws with washers, place two in each mantel side assembly (see Figure 4, page 3). With two 1 1/4" screws with washers, attach top to header. Make sure all pieces are aligned properly and tighten, leaving screws slightly loose.

www.desatech.com

121340-01B

Image 2
Contents Corbel Installation Assembling MantelMantel Top Assembly Leg AssemblyHeader Assembly Finishing Mantel Gas Fireplace InstallationFor Dimplex Fireplace Use Only Electric Fireplace Installation Assembling Perimeter Trim If Supplied with Gas FireplaceBase y repisa de chimenea para pared W32LS2 Ensamble de la cabecera Instalación de la ménsulaEnsamble de columna Sólo para usar con la chimenea eléctrica Dimplex Instalación de la chimenea a gasEnsamble superior de la repisa de chimenea Acabado de la repisa de chimeneaInstalación de chimenea eléctrica Figura 7 Armado del adornoImportant une étiquette avec un numéro de série se trouve Assemblage du manteau de foyerDurée dassemblage estimée 45 minutes Sur la base et alignez les trous filetés sur les équerres De fixation doivent faire face à lextérieurPlacez lassemblage du côté et du support latéral droits Faites passer les vis de 12 mm 1/2 po par les équerresPas les vis à fond Installation du foyer au gazAssemblage de la tablette du manteau de foyer Installation du foyer électrique Assemblage de la finition

W32LS2 specifications

Desa W32LS2 is a state-of-the-art heating system designed to provide efficient and reliable warmth for both residential and commercial spaces. This innovative device combines advanced technologies with user-friendly features, making it a preferred choice for many.

One of the standout features of the Desa W32LS2 is its powerful output capacity. With a heating capacity of 32,000 BTU, it can effectively warm medium to large rooms, ensuring a comfortable environment during the colder months. The system is equipped with a built-in thermostat that allows users to set their desired temperature, which helps maintain consistent heat levels throughout the space.

The Desa W32LS2 utilizes advanced infrared heating technology, which is known for its energy efficiency. Unlike traditional heating systems that warm the air, infrared heaters work by warming objects and people in the room directly. This results in faster heat distribution and less energy consumption, ultimately leading to lower utility bills.

Another significant characteristic of the Desa W32LS2 is its aesthetic design. The unit features a sleek and modern look that fits seamlessly into any decor. Its compact size makes it easy to place in various locations without taking up too much space. Additionally, the appliance is available in different finishes, allowing homeowners to choose a style that best matches their interiors.

Safety is a priority with the Desa W32LS2, which includes multiple safety features such as an automatic shut-off function. This safety mechanism ensures that the heater turns off if it overheats or tips over, providing peace of mind for users, especially in homes with children or pets.

The installation process of the Desa W32LS2 is straightforward and does not require professional assistance, making it accessible for the average homeowner. The user-friendly controls allow for easy adjustments to settings, ensuring that everyone can operate the heater without any complications.

In conclusion, the Desa W32LS2 stands out as a highly efficient and safe heating solution. Its powerful heating capacity, energy-saving infrared technology, aesthetic design, and user-friendly features make it an excellent option for anyone looking to enhance their indoor comfort during the winter months. With the right balance of functionality and style, the Desa W32LS2 is a valuable addition to any living or working space.