Desa (V)TC36PE To Turn OFF GAS To Appliance, Optional Remote, Operation, Burner Flame Pattern

Page 24

24

OPERATING FIREPLACE

To Turn Off Gas To Appliance

Optional Remote Operation

Operating Optional Blower Accessory

INSPECTING BURNERS

Pilot Assembly

Burner Flame Pattern

OPERATING FIREPLACE

Continued

TO TURN OFF GAS

TO APPLIANCE

1.Turn off the wall switch.

2.Turn off all electric power to the appliance if service is to be performed.

3.Open lower louver panel.

4.Remove front hearth brick and control access panel.

5.Turn equipment shutoff valve clockwise to OFF. Do not force.

6.Close lower louver panel.

Pilot Burner

Sensing Rod

 

Ignitor

 

Figure 43 - Pilot

 

OPTIONAL REMOTE

OPERATION

 

Note: The WRC receiver and hand-held remote control kit

must be purchased separately (see Accessories, page 34). Follow

installation instructions on page 22.

 

1.Turn equipment shutoff valve to ON position. You can now turn the burner on and off with the hand-held remote control unit. IMPORTANT: Be sure to press the ON/OFF buttons on the hand-held remote control unit for up to 3 seconds to assure proper operation.

2.Press the ON/OFF button to turn the burner on and off.

OPERATING OPTIONAL

BLOWER ACCESSORY

Locate the blower controls by opening the lower louver panel on the fireplace. Blower controls are located on the left side of the switch bracket to the right just inside the louver panel.

The BK manual blowerand the BKTthermostatically-controlled blower have an ON setting and an OFF setting. The blower will only run when the switch is in the ON position. In the OFF position, the blower will not operate.

Note for BKT Only: If you are using BKT blower with optional thermostat (wall mounted or remote control) for the fireplace, your fireplace and blower will not turn on and off at the same time.The fireplace may run forseveral minutes before the blower turns on. After the heater modulates to the pilot position, the blower will continue to run. The blower will shut off after the firebox temperature decreases.

The blower helps distribute heated air from the fireplace. Peri- odically check the louvers of the firebox and remove any dust, dirt or other obstructions that will hinder the flow of air.

INSPECTING BURNERS Check pilot flame pattern and burner flame patterns often. PILOT ASSEMBLY

The pilot assembly is factory preset for the proper flame. Altera- tions may have occurred during shipping and handling. The pilot is located on the left hand side of the burner.

The flame must envelope 1/4" of top of the ignitor/sensor and grounding stem.

If your pilot assembly does not meet these requirements:

•Turn the adjustment screw marked PILOT clockwise to decrease or counterclockwise to increase the flame to proper size (see Figure 42, page 23). Do not remove the adjustment screw.

•see Troubleshooting, page 26

Pilot Burner

Sensing Rod

 

 

Ignitor/Sensor

Figure 44 - Correct Pilot Flame Pattern

BURNER FLAME PATTERN

Burner flames will be steady; not lifting or floating. Flame patterns will be different from unit to unit and will vary depending on instal- lation type and weather conditions.

If the vent configuration is installed incorrectly, the flames will lift or "ghost". This can be dangerous. Inspect the flames after instal- lation to ensure proper installation and performance.

Figure 45 shows a typical flame pattern. If burner flame pattern differs from that described:

•turn fireplace off (see To Turn Off Gas to Appliance)

•see Troubleshooting, page 26

Figure 45 - Typical Flame Pattern

www.desatech.com

116234-01B

Page 23 Page 25
Image 24
Page 23 Page 25
Contents For Your Safety For Your Safety What to do if YOU Smell GASTable of Contents Safety InformationSafety Information Product Identification Local CodesProduct Features PRE-INSTALLATION PreparationLocation and Space Requirements Clearances Framing and FinishingVent Specific venting clearancesLocation of Termination CAP Termination CAP AIR Supply Inlet GAS MeterVenting Installation Instructions Installation PrecautionsInstallation Planning Horizontal Termination InstallationMale Female Slots Locking Lugs CenterVent Cap Wood Screw Interior Wall Surface Firestop Vent CapHorizontal Vent PipeHorizontal Termination Configurations Recommended Applications Corner ground floor installation Over 12 horizontal pipeTermination is possible Venting with Two 90 Elbows Installation for Vertical Termination Flat Ceiling InstallationConnect a section of pipe and extend up through the hole Roof Flashing Wall Strap Elbow Ceiling FirestopVertical Termination Configurations Elbow Into inner collar fireplace as shownHigh Altitude Installation Venting Installation Fireplace Installation Check GAS TypeInstalling Optional Blower Accessory Desa 5/8 Pipe & Vent KitsFireplace Installation Model BKT InstallationBy turning knob fully counterclockwise before continuing Decal on the firebox bottom approximately 12 in frontInstalling GAS Piping to Fireplace Location Blower Wiring DiagramInstallation Items Needed Connecting Fireplace to GAS Supply Pressure Testing Gas Supply Piping SystemChecking GAS Connections Pressure Testing Fireplace Gas Connections REMOVING/REPLACING Glass DoorRemoving Louver Panels Bubbles forming show a leak. Correct all leaks at onceInstalling Lava Rock and Glowing Embers Cleaning Glass DoorRemoving Glass Door Installing Brick Liner Models BL36DASA and BL36DHASA Wall Switch InstallationOptional Remote Control Extension Cord IgnitionWiring Diagram Operating FireplaceLighting Instructions Equipment PilotOperating Optional Blower Accessory To Turn OFF GAS To ApplianceOptional Remote OperationCleaning Maintenance Glass DoorPilot and Burners LogsTroubleshooting Position BL36DHASA for log/grate removalImproper vent configuration Restrictions or obstructionReplacement Parts Service HintsTechnical Service Parts Under WarrantySpecifications Illustrated Parts Breakdown Models TC36NE, VTC36NE, TC36PE and VTC36PEParts List KEY Part Number TC36NE/PE VTC36NE/PE Description QTY19 18 KEY Part Number Description Accessories Brand ModelDate Purchased Serial Number Industrial Drive Box Bowling Green, KY 116234-01B Warranty Information Model Serial No Date PurchasedIndustrial Drive P.O. Box

(V)TC36NE, (V)TC36PE specifications

Desa (V)TC36NE and (V)TC36PE are advanced heating solutions designed to provide both efficiency and comfort in residential and commercial settings. These two models stand out for their innovative engineering, modern design, and user-friendly features, making them ideal choices for individuals seeking reliable temperature control.

The central feature of both models is their high-efficiency combustion systems, which optimize fuel usage to reduce environmental impact while saving on heating costs. The (V)TC36NE and (V)TC36PE are equipped with state-of-the-art burners that ensure complete combustion, resulting in clean emissions and enhanced performance. With an exceptional energy rating, these units contribute to a greener environment by minimizing the carbon footprint.

Another notable characteristic is the versatile installation options these units offer. The (V)TC36NE, designed for natural gas use, can be seamlessly integrated into existing heating systems, while the (V)TC36PE operates with propane, catering to a broader range of installation scenarios. This flexibility enables homeowners and businesses to select the model that best fits their fuel supply and heating needs.

Both models come with advanced controls that grant users precise temperature regulation. With smart technology integration, users can operate these heating units remotely via smartphone applications, allowing for personalized heating schedules and real-time monitoring. This feature not only enhances user convenience but also promotes energy efficiency by preventing energy waste.

The design of the (V)TC36NE and (V)TC36PE models is another highlight, showcasing a sleek and contemporary aesthetic that complements various interior decors. The units are constructed with durable materials, ensuring longevity and reliability even under demanding conditions. Furthermore, their quiet operation enhances the overall comfort of the environment, making these units suitable for bedrooms, offices, and other noise-sensitive areas.

In summary, the Desa (V)TC36NE and (V)TC36PE models merge innovative technology with practical design and efficiency. With their advanced combustion systems, versatile installations, smart controls, and stylish appearance, they offer an ideal heating solution for modern living spaces. Homeowners and businesses looking to enhance their heating performance while maintaining environmental consciousness can find a compatible option in these exceptional models.
Top Page Image Contents