Desa (V)T36ENA Fireplace Installation, Parts Lists for Venting Kits and Components

16	VENTING INSTALLATION INSTRUCTIONS
	Parts Lists for Venting Kits and Components
	FIREPLACE INSTALLATION
	Check Gas Type
	Installing Optional Blower Accessories

VENTING INSTALLATION INSTRUCTIONS

Continued

PARTS LISTS FOR VENTING KITS AND COMPONENTS

DESA Pipe & Vent Kits

Number Description

P47-6 6" Section Coaxial Pipe - Galvanized

P47-12 12" Section Coaxial Pipe - Galvanized

P47-24 24" Section Coaxial Pipe - Galvanized

P47-36 36" Section Coaxial Pipe - Galvanized

P47-48 48" Section Coaxial Pipe - Galvanized PA47-712 Adjustable 7"-12" Section Coaxial Pipe - Galvanized VKG-47 Ground Floor Vent Kit - Galvanized

Includes:45°Elbow,7"-12"AdjustablePipe,WallFirestop, Horizontal Square Termination, and 16 Screws

VKB-47 Basement Vent Kit - Galvanized

Includes: 45° Elbow, 7"-12" Adjustable Pipe, Wall Firestop, Horizontal Square Termination, 4' Pipe, 90° Elbow, and 20 Screws

VKS-47 Snorkel Kit - Galvanized

Includes: 45° Elbow, 7"-12" Adjustable Pipe, Wall Firestop, 36" Snorkel Termination, 4' Pipe, 90° Elbow, and 26 Screws

VKR-47 Roof Vent Kit - Galvanized

	Includes: 45° Elbow, 7"-12" Adjustable Pipe, Flue Re-
	strictor, Vertical High Wind Termination, 2' Pipe, 4' Pipe,
	Firestop Plate, Roof Flashing (0/12-6/12), and 26 Screws
VKC-47 Corner Vent Kit - Galvanized
	Includes: 45° Elbow, 7"-12" Adjustable Pipe, Hori-
	zontal Termination, 6" Pipe, 90° Elbow, Wall Firestop,
	and 18 Screws
HTK	Horizontal Round Termination Kit
	Includes: Round Termination, Wall Firestop, and 45° Elbow

DESA Elbows

Number Description

E47-45 45° Elbow - Galvanized

E47-90 90° Elbow - Galvanized

DESA Terminations

Number Description

HT-47 Horizontal Round Termination - Galvanized HTS-47 Horizontal Square Termination - Galvanized

VT-47 Vertical Round Termination - Galvanized

ST-47-14 14" Snorkel Termination - Galvanized

ST-47-36 36" Snorkel Termination - Galvanized

DESA Venting Accessories

Number	Description
SC-47	Storm Collar - Galvanized
WF-47	Wall Firestop - Galvanized
RF-47-6	Roof Flashing - 0 to 6/12 Pitch - Galvanized
RF-47-12	Roof Flashing - 6/12 to 12/12 Pitch - Galvanized
VR-47	Vertical Restrictor - Galvanized
S-47	Combustible Siding Standoff - Galvanized
WS-47	Wall Strap
FP-47	Firestop Plate

FIREPLACE INSTALLATION

CHECK GAS TYPE

Use proper gas type for the fireplace unit you are installing. If your gas supply is not correct, do not install fireplace. See retailer where you purchased the fireplace for proper fireplace according to your gas type or to purchase gas conversion kit (see Accessories, page 39).

INSTALLING OPTIONAL BLOWER

ACCESSORIES

NOTICE: If installing blower in an existing fireplace with gas connections, shut off gas supply and dis- connect heater from gas supply. Contact a qualified service person to do this.

WARNING: If there is a duplex electrical outlet installed in the right side of the bottom of the fireplace base area, be sure that the electrical power to the outlet is turned off before proceeding with blower installation. Failure to do this may result in serious injury.

Model BK Installation

Follow all instructions provided in the blower accessory kit.

1.Attach the power cord to the blower motor by firmly pushing the two female terminals at the end of the power cord onto the two spade terminals on the blower motor (see Figure 25, page 17).

2.Attach green ground wire from power cord to blower hous- ing using screw provided (see Figure 25, page 17). Tighten screws securely.

3.Place the blower against the lower rear wall of the firebox outer wrapper with the exhaust port directed upward. The blower will fit inside the back opening and be held in position against the back wall by the magnets (see Figure 25, page 17).

For..com

111251-01B