Desa VC36N, VC36P, CGCDV36NR, CGCDV36PR Operating Fireplace, For Your Safety Read Before Lighting

FIREPLACE INSTALLATION

Installing Optional Brick Liner Models BL36DA(SA) and BL36DHA(SA)

OPERATING FIREPLACE

For Your Safety Read Before Lighting

Lighting Instructions

23

FIREPLACE INSTALLATION

Continued

INSTALLING BRICK LINER MODELS BL36DA(SA) AND BL36DHA(SA)

WARNING: If fireplace has been running, turn off unit. Let cool before installing brick liner.

You may purchase brick liner from your local retailer or see Ac- cessories, page 36.

CAUTION: Always handle brick panels with two hands. Do not force brick panels into place. Exces- sive force will break brick panels.

1.Remove top and bottom louvers to allow access to door latches.

2.Unlock door latches and open glass door. See Removing Glass Door, steps 1 and 2, page 22.

3.Carefully remove lava rock and ember material. Remove log/ grate assembly by unscrewing grate from plenum. The two logs under the grate are attached to burner. DO NOT attempt to remove.

4.Remove screws that attach plenum to burner to remove plenum.

5.Remove three screws from deflector shield on the inside top of firebox. Set shield and screws aside.

6.Install rear brick panel first. Rest bottom edge of panel on back edge of burner assembly (see Figure 43).

7.Install left side brick panel by sliding it between the burner assembly and the side of the firebox (see Figure 43).

8.Install the right brick panel using the same method described in step 6 for left brick panel.

9.Replace deflector shield using screws removed in step 4.

10.Using scews removed in step 4, replace plenum and attach to burner.

Left Side

Brick Panel

Rear Brick

Panel

Figure 43 - Installing Rear Brick Panel

11.Using screws removed in step 3, replace log/grate assembly. Be care- ful when replacing log/grate assembly not to chip logs on burner.

12.Install lava rock and glowing embers. See Installing Lava Rock and Glowing Embers, page 22.

13.Close glass door and lock latches on top and bottom of door and replace screen. See Removing Glass Door, steps 5 and 6 on page 22.

14.Close top and bottom louvers.

OPERATING FIREPLACE

FOR YOUR SAFETY READ

BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING

INSTRUCTIONS

1.STOP! Read the safety information above.

2.Open lower louver panel.

3.Turn off all electric power to the fireplace.

4.Push in gas control knob slightly and turn clockwise to “OFF”.

5.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information above. If you don't smell gas, go to the next step.

6.The pilot is located by the main burner and should not require accessing for lighting.

116200-01C www.desatech.com