Fireplace Assembly

Inspire Electric Fireplace

Unpack the Appliance

The Inspire Electric Heater is supplied in two (2) car- tons. All instructions should be read before beginning installation.

Carton 1 contents

1, Electric heater main body

1, Remote control handset with battery 1, Mounting hanger

1, Mounting hardware kit [#12 x 1/2” long screws (6), wall anchors (6), #8 x 1/4” short screws (4)]

1, Installation instructions 1, Pebble pack

2, Insert panels

Carton 2 contents

1, Trim assembly w/ six (6) magnets

Appliance Mounting

The heater must be mounted to a suitable wall using the mounting hanger provided. Consider the minimum clearance dimensions referenced on Page 3 and 4 for the mounting location. The following steps are for one method that can be used at your own risk. A helper is recommended.

1.Become familiar with the mounting hanger and how it ﬁts to the rear of the electric heater main body. (Fig. 2)

Mounting Hanger

Wiring Diagram

FP1731

Fig. 2 Rear view of Inspire with mounting hanger in place.

2.Locate the heater main body on the wall and mark (erasable) either the bottom or top edge and one side for the heater location. If the heater is to be centered on the wall area, the side mark is not nec- essary. Set the heater main body down.

3.Mark a horizontal line 21¹⁄₈” (536 mm) from the lower line or 2¹⁄₄” (58 mm) from the upper line.

4.Measure half the width [16³⁄₈” (416 mm)] of the heater main body and mark a vertical line to cross the horizontal line. If the heater main body is to be centered on the wall area, mark a vertical center line to cross that horizontal line. Where the horizontal and vertical marks cross is the location of the upper center mounting hanger hole.

5.Use an appropriate level and mark and measure the locations for the remaining holes of the mounting hanger. Use the mounting hanger as a template.

6.Use the long screws provided to mount the hanger in place. A #3 Phillips screwdriver is recommended. Depending on the wall type, proper anchors have to be used. For your convenience, expansion anchors are provided. Be sure to check the anchors for suit- ability for the wall type.

7.Mount the heater main body to the hanger.

Heater Assembly

Before assembling the trim to the heater main body, arrange the pebbles onto the plastic front form (ember lava rock), to give the best decorative effect. Refer to front cover for example. If necessary, the side brackets for the plastic front form may need to be removed to ﬁt and reinstall.

Trim Assembly

Place the trim insert panels on either side of the trim and secure to the trim using the screws provided. (Two

(2) screws on either side)

1.Remove the protective plastic bag and place the trim on it to prevent any damage to the front while work- ing.

2.Peel off the protective plastic coating (if available) on the insert panel.

3.Place the insert panel on either side as shown in Figure 3. Secure each panel using two (2) short screws. The screws ﬁt into slots in the trim. A me- dium #2 Phillips screwdriver is recommended.

4.Double the six (6) magnets and place on the trim in three locations as shown in Figure 4.

10009472

ICVCTK01, ICVCTK02 specifications

Vermont Castings offers a range of high-performance gas fireplaces, and two notable models in their lineup are the ICVCTK02 and ICVCTK01. These models stand out for their blend of classic design, advanced technology, and powerful heating capabilities.

The ICVCTK02 and ICVCTK01 fireplace inserts share many features that make them popular choices among homeowners looking to enhance their living spaces with warmth and ambiance. One of the most prominent characteristics of these models is their elegant cast iron construction, which not only provides a timeless aesthetic but also contributes to efficient heat retention and distribution. The durable cast iron body helps maintain consistent temperatures, allowing for even heating throughout the room.

Both models are equipped with Vermont Castings' innovative burner technology, designed to provide a clean and efficient burn. This ensures that these fireplaces offer a higher heat output with lower emissions, making them an environmentally friendly choice. The advanced burner system also provides the option for both natural gas and propane fuel sources, catering to the preferences and availability of different households.

An important feature of the ICVCTK02 and ICVCTK01 is their impressive BTU output. These models are capable of producing a substantial amount of heat, making them well-suited for rooms of various sizes. The controlled heat output allows users to customize their heating experience, ensuring comfort during colder months.

Furthermore, the ICVCTK02 comes with the additional advantage of a multi-function remote control, allowing homeowners to adjust the flame height, control the blower speed, and set timers without having to leave their seats. The ICVCTK01, while slightly more basic in its controls, still offers easy access to user-friendly features that enhance the overall experience.

Both fireplace inserts also emphasize usability and safety. They feature a large viewing window that provides a great view of the beautiful flames, while the glass door keeps the fire contained and safe. Additionally, safety features include a heat-resistant glass and ventilation systems designed to reduce the risk of overheating.

In summary, the Vermont Castings ICVCTK02 and ICVCTK01 fireplace inserts combine elegance, efficiency, and modern technology. With their stunning cast iron design, advanced burner performance, and user-friendly features, these fireplaces are an excellent investment for creating a cozy and inviting atmosphere in any home.