Vermont Casting EWF30 installation instructions Chimney System, Replacing the Door Gaskets

Page 23

1.Remove the existing fiberglass gasket by grasping an end and pulling firmly.

2.Use a wire brush or the tip of a screwdriver to clean the channel of any remaining cement or bits of gas- ket.

3.Apply a thin bead of fireplace cement to the newly- cleaned groove.

4.Pack a new gasket into the groove. Wait until you have placed all but a couple inches from the end before you trim the end to an exact fit.

5.Place door back on fireplace, latch door and keep closed for 1/2 hour to insure cement has set.

Replacing the Door Gaskets

Remove the door by lifting it straight up off its hinge pins. Lay it face down on a padded surface.

Follow steps 1-4 as described above.

Replace Damaged Door Glass Immediately

Do not operate the fireplace with damaged glass door. Use the following procedure for glass replacement.

NOTE: Replace glass only with the replacement glass made for this unit, available from your authorized dealer.

•Remove the door and loosen the retaining clips which hold the glass to the door frame. Remove clips. Use caution when handling broken glass.

•Examine the gasket that seals the glass to the door frame. Replace if necessary with gasket obtained from your local Vermont Castings’ Authorized Dealer. See the directions for gasket replacement on Page 23.

•Check the flat surface of the door frame, and clear away debris if necessary.

•Install the new glass.

•Secure the clips, being careful not to overtighten. Be sure the glass is firmly seated against the gasket.

•Replace door.

Vermont Castings EWF30

The Chimney System

A Clean Chimney System is

Safer and Works Better

Although the combustion system in the EWF30 can re- duce creosote formation dramatically, it is not a substi- tute for regular inspection and cleaning of the chimney and chimney connector.

Learn to Recognize — and Avoid — Creosote

The EWF30 has been designed to reduce creosote build-up significantly. However, regular chimney in- spection and maintenance must still be performed. For safety, good fireplace performance, and to protect your chimney and chimney connector, inspect your chimney and chimney connector on a regular schedule. Clean the system if necessary. Failure to keep the chimney and connector system clean can result in a serious chimney fire.

When wood is burned slowly, it produces tar, organic vapors and moisture which combine to form creosote. The creosote vapors condense in the relatively cool chimney flue of a slow-burning fire. As a result, creo- sote residue accumulates on the flue lining. When ignit- ed, this creosote makes an extremely hot fire within the flue system that can damage the chimney and overheat adjacent combustible material. If a significant layer of creosote has accumulated —1/8” (3mm) or more — it should be removed to reduce the risk of a chimney fire.

If you do experience a chimney fire, act promptly to:

•Close the primary air control lever and the damper

•Get everyone out of the house.

•Call the Fire Department.

You should inspect the system every two weeks during the heating season as part of a regular maintenance schedule. To inspect the chimney, let the fireplace cool completely. Remove the termination top. Then, using a strong light, sight down into the chimney flue.

Clean the chimney using a specially designed brush the same size and shape as the flue liner. Flexible fiberglass rods are used to run the brush up and down the liner, causing any deposits to fall to the bottom of the chimney where they can be removed through the damper on top of the fireplace.

If you can not do the chimney inspection yourself, con- tact your local Vermont Castings’ Authorized Dealer, or engage a professional chimney sweep to perform the inspection and cleaning of the chimney.

20008662

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents EWF30 Introduction Table of ContentsDrafts Safety InformationPrecautions DescriptionEWF30 Woodburning Fireplace SpecificationsFireplace and chase parts identification Chase InstallationChimney Requirements Offset Installations Ten Foot Rule Planning InformationMounting the Fireplace Planning the Chimney RunInsulating Fireplace Enclosure for Cold Climates InstallationChase Installation Chimney SupportsEB1 Receptacle Hookup Straight-Up Chimney InstallationOffset Installation FramingFraming the Ceiling Hole Positioning, Safety Strips Securing the FireplaceCeiling Chimney Hole Possible Obstructions Cutting the HoleInstallation Instructions Installing Outside Air KitInstallation Precautions Use outside air cover plate to cover air inlet opening Installing the Chimney SystemCanadian Requirements For Insulation Shield Installing the Firestop Spacer Ceiling HoleProper Firestop Spacer Installation Continue Installing Pipe to Complete RunPenetrating the Roof Install Remainder of Chimney SectionsInstall Top Housing or Termination Installing Chimney in a ChaseSide View MantelsExample of Determining Hearth Extension Equiva- lents Hearth InstallationSide Wall Protection Examples of wall shield insulationMinimum Wall Clearances EWF30 Controls OperationAttach Handles DamperBurn Only High-Quality Wood Use the Air Control Settings That Work Best for YouFan Glass DoorsSpecial Tactics for Cold-Climate Heating Starting and Maintaining a Wood FireReloading and Reviving a Wood Fire Remove and Store Ash Safely How to Replace Gaskets MaintenanceCleaning the Glass Adjust the Door Latch PeriodicallyReplace Damaged Door Glass Immediately Clean Chimney System is Safer and Works BetterChimney System Replacing the Door GasketsFireplace Daily Maintenance ScheduleYearly Spring Cleaning Component Description Model Number Chimney ComponentsDescription EWF30 FireplaceRef. Description EWF30 FireplaceGravity Vent Kit Optional AccessoriesFan Kit Screen KitModel Description Trim KitsVermont Castings EWF30 Limited Lifetime Warranty CFM Corporation
Related manuals
Manual 32 pages 28.92 Kb

EWF30 specifications

The Vermont Casting EWF30 is a testament to innovation and craftsmanship in the world of cast iron wood stoves. This highly efficient wood-burning stove combines traditional aesthetics with modern technology, making it a perfect centerpiece for both rustic and contemporary homes. One of the standout features of the EWF30 is its impressive heating capacity. Designed to heat areas up to 2,000 square feet, it is ideal for large spaces, providing consistent warmth during chilly months.

Constructed from high-quality cast iron, the EWF30 offers a durability that only improves with age. This material is known for its excellent heat retention and distribution, resulting in a steady, comfortable warmth. The stove’s classic design includes large ceramic glass windows, allowing users to enjoy the mesmerizing beauty of the fire while safely keeping the warmth inside.

Incorporating advanced technology, the Vermont Casting EWF30 features a clean burning system that significantly reduces emissions. This is a critical aspect for environmentally conscious consumers, as the stove adheres to strict EPA standards, promoting cleaner air and reduced environmental impact. The efficiency of this wood stove is exceptional, with a thermal efficiency rating that maximizes heat output while minimizing fuel usage.

The EWF30 is equipped with a user-friendly air control system, allowing for easy adjustments to the airflow. This system enhances the combustion process, enabling users to achieve the desired flame and heat levels effortlessly. The top-loading design also simplifies the refueling process, making it easier to add wood without disturbing the existing fire.

Aesthetically, the Vermont Casting EWF30 can be customized with various finishes, including traditional black, enamel, and even bold colors, ensuring it fits seamlessly with any interior decor. Additionally, this model includes a removable ash pan, providing a convenient cleaning option.

In summary, the Vermont Casting EWF30 is more than just a wood stove; it is a fusion of tradition and technology. Its heating efficiency, durability, and aesthetic appeal make it a worthy investment for anyone seeking a reliable and stylish heating solution for their home. Whether for ambiance or functionality, the EWF30 is designed to enhance the living experience while respecting the environment.
Top Page Image Contents